


全文预览已结束
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1 USB測試標准測試標准 USB Electrical Mechanical and Environmental Compliance Standards Test Descriptio Performance Requirement Visual and Dimensional Inspection Must meet or exceed the requirements specified by the most current version of Chapter 6 of the USB Specification Insulation Resistance 絕緣電阻 大于等于1 000 Dielectric Withstanding Voltage 耐電壓 The dielectric must withstand 500V AC for one minute at sea level 500 V AC 一分鐘 Low Level Contact Resistance 低電平接觸電阻 30 m maximum when measured at 20mV maximum open circuit at 100mA Mated test contacts must be in a connector housing 在開 最大電 為100 mA電壓為20mV情況下最 大為30m Contact Current Rating 溫升 1 5A at 250V AC minimum when measured at an ambient temperature of 25 with power applied to the contacts the T must not exceed 30 at any point in the USB connector under test 相對溫 為25 250VAC 最小為1 5A 接通電 壓 測試中端子任一點的溫 超過 30 Contact Capacitance 接觸電容 2 pF maximum unmated per contact 最大為2pF Insertion Force 插入 35 N maximum at a maximum rate of 12 5 per minute 在插入速 超過每分鐘12 5 時 超過35N Extraction Force 撥出 10 N minimum at a maximum rate of 12 5 per minute 在拔出速 超過每分鐘12 5 時 超過10N Durability 耐用性 1 500 insertion extraction cycles at a maximum rate of 200 cycles per hour 在速 超過每小時200個循環下經受1 500次插 入與撥出 Cable Pull Out 電纜 出 After the application of a steady state axial load of 40 N for one minute 固定后施加40N的軸向 一分鐘 2 Test Descriptio Performance Requirement Physical Shock 物 沖擊 No discontinuities of 1 s or longer duration when mated USB connectors are subjected to 11ms duration 30 Gs half sine shock pulses Three shocks in each direction applied along three mutually perpendicular planes for a total of 18 shocks 匹配USB端子 中斷 得大于或等于1 s 30Gs的 半波脈沖承受11ms 從三個正交的方向施加沖 擊 總沖擊 為18次 Random vibration 任意振動 No discontinuities of 1 s or longer duration when mated USB connectors are subjected to 5 35Gs RMS 15minutes in each of three mutually perpendicular planes 匹配USB端子 中斷 得大于或等于1 s 承受 5 35Gs RMS 朝各個正交的方向各振動15分鐘 Thermal Shock 熱沖擊 10 cycles 55 and 85 The USB connectors under test must be mated 在 55 至 85 中循環10次 端子必須緊密配合 Cable impedance 阻抗 Impedance must be in the range specifiedin Z0 90 15 ZCM 30 30 Signal Pair Attenuation 衰減 Refer to Section 7 1 17 Frequency att max 0 064 0 08 0 256 0 11 0 512 0 13 0 772 0 15 1 0 2 4 0 39 8 0 54 12 0 67 24 0 95 48 1 35 96 1 9 200 3 2 400 5 8 3 Test Descriptio Performance Requirement Propagation Delay 傳輸延遲 See Section 7 1 1 1 Section 7 1 4 Section 7 1 16 and Table 7 9 5 2ns m MAX Propagation Delay Skew 延遲偏移 Propagation skew must met the requirements as listed in Section 7 1 3 最大 超過100ps cable Solderability 可焊性 USB contact solder tails must pass 95 coverage after one hour steam aging as specified in Category 2 在經過一個小時的蒸氣 化后焊接端的覆蓋 大 于95 Humidity 抗潮性 168 hours minimum The USB connectors under test must be tested in accordance with EIA 364 31 大于168個小時 如EIA 364 31測試 Flammability The manufacturer will require its thermoplastic resi
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 【正版授权】 IEC TR 63309:2025 EN Active fibres – Characteristics and measurement methods – Guidance
- 2025至2030中国电镀表配件行业深度研究及发展前景投资评估分析
- 2025至2030中国电子商务食品行业深度研究及发展前景投资评估分析
- 2025至2030中国电动尾门行业产业运行态势及投资规划深度研究报告
- 2025至2030中国玛瑙饰品行业市场占有率及投资前景评估规划报告
- 技术培训推动教师职业发展的重要动力
- 幼儿园营养性疾病知识培训
- 智慧教育大数据驱动的教学效率变革
- 探索不同国家在线教育平台的创新实践
- 教育中的心理学技巧激发学生潜能的实践
- 【MOOC】教育研究方法-浙江大学 中国大学慕课MOOC答案
- 《回归分析》课件
- 心脏手术围手术期
- 餐车经营食品安全应急预案
- DB43T 876.11-2017 高标准农田建设 第11部分:耕地地力评定技术规范
- 2024新版(外研版三起孙有中)三年级英语上册单词带音标
- 2024至2030年中国汉白玉石雕数据监测研究报告
- 三年级下册混合计算题100道及答案
- DB12T 998-2020 殡葬服务机构消毒卫生规范
- 广东省广州市五校2023-2024学年高一下学期期末联考化学试卷
- 2024年天津高考数学真题试题(原卷版+含解析)
评论
0/150
提交评论