变压器材料-标签检验标准.doc

Inspection standard for label 标签检验标准1.0 OBJECTIVE 目的To define a procedure that provides for acceptance of parts quality by the end user through inspection for a specification time at a specified distance.建立此程序以确保通过最终客户定时定点的检测后所提供的零部件质量接收要求。2.0 SCOPE 范围3.0 DEFINE 定义 Major defects: Point serious impact to the vision and use; And cant reach to the design requirement. 主要缺点: 指严重的影响使用及严重影响视觉;及无法达到原设计要求的缺点; Min defects: Point impact to vision; And no important dimension according to the assy drawing. 次要缺点: 指轻微影响视觉及非关键尺寸的缺点; 4.0 SAMPLING PLAN AND ACCEPTABLE QUALITY LEVEL 抽样计划和允收水平4.1 Sampling plan: 抽样计划 According to sampling plan of schaffner EMC of shanghai, the sampling grade is divided into: Reduce sampling, normal sampling, increase sampling. 抽样方案按照兆启上海的抽样计划，抽样等级分为：正常抽样，减少抽样，加强抽样。正常选择抽样比例依照一般检验水准II级。 4.2 Acceptable Quality Level 允收水准: Appearance inspection: major defect for AQL0.65, min defect for AQL1.5, the sample plan is class two according to general inspection levels.外观检验: 主要缺陷为AQL0.65; 次要缺陷为AQL1.5;Dimension inspection: zero defect.尺寸检验: 零缺陷; *REFERENCE INFO: MIL-STD-105E *参考资料: MIL-STD-105E5.0 INSPECTION EQUIPMENTS检验设备5.1 Appearance inspection: view 外观检验：目视5.2 Dimension inspection: caliper, micrometer 尺寸检验：卡尺，千分尺5.3 Function inspection: scance, view 性能检验：扫描仪，目视6.0 INSPECTION CONDITION检验条件6.1 Table 1 shows the viewing time and distance for each designated area Or surface. Inspection of parts and products will be under the following Viewing conditions.表1给出了对每个指定区域或表面的目测距离和时间，零件和产品的检验应遵循以下目测条件。6.2 Use uniformity; non-directional illumination to a minimum of 500 Lux. Caution should be shown to avoid over inspection. 应使用均匀、无方向性、至少500勒克司的照明以避免检查不当。6.3 All Inspection areas will be deemed as designation viewing areas .所有检验区域应视为指定目检区域。6.4 Inspection must be made by individual with 1.0 vision or vision corrected to 1.0.检验员裸视力和矫正视力为1.0。Table1 Time and Distance 时间及距离Category类别Viewing Distance目测距离Viewing Time目测时间Surfaces表面条件50cm距离50cm5 seconds max最多5秒Fronts前面7.0 Appearance inspection 外观检验S/N 序号Inspection items检验项目Inspection standard 检验标准Defect grade缺陷等级Remark 备注MAMI1C01-Dirtyor, Bolt, Spot / 脏污,污点,斑点Less than the diameter 5cm, 2 points; 小于直径5cm允许2点.2C02-Color deviation / 色差None, can according to limit sample 不允许色差，可参照限度样品接收3C03-Crack / 破损None 不允许破损.4C04-Printing content, location, font printing. 印刷内容, 位置, 字体印刷Must to conform with drawing or sample and the font must is clear can be identify.须与图纸要求或样品一致以及字体必须清晰可识别.5C05-Material / 材质The material must to conform with drawing.材质须符合图纸要求.6C06-Figure / 外形Must to conform with drawing.外形须符合图纸要求.7C07-Cut side / 切边Must is trim.须整齐.8C08-Level degree / 平整度Must to level off, no deformation.须平整，无变形.9C09-Series number / 序列号The series number shortage of every lot must less than 5pcs序列号码短缺每一批必须小于千分之五.10C10-Park / 包装Must attach series numbers record in every shipment.每一批必须附有序列号码记录.Note: When dont description above table, Please according to the actual limit samples.备注: 当在上表没有描述时, 请参考/依照实际的限度样品. 8.0 Dimension inspection 尺寸检验 S/N序号Inspection items检验项目Inspection standard检验标准Defect grade缺陷等级Remark备注MAMI1Width 宽度According to drawing依照图纸2Length 长度According to drawing依照图纸3Thickness 厚度According to drawing依照图纸4Other dimension其它尺寸According to drawing依照图纸Remark: Measure quantity 测试数量: 5pcs / lot / 每批5张9.0 Function inspection / 性能检验 9.1 Test name: scan the series numbers.测试名称: 条码扫描.Test object: aim at have series numbers label need to do this test. 测试对象: 针对于有序列号的标签须做这项测试. Test tool: scanner. 测试工具: 扫描仪. Inspection standard: series numbers is correct and no repetition. 检验要求: 序列号正确且无重号. Test quantity: 50pcs/lot, if less than 50pcs when incoming, all need to scan. 测试数量: 50张/批, 如果进料小于50pcs，则实际来多少须全检多少.9.2 Test name: adhesive test.测试名称: 粘性测试Test method: for the width 35mm need to affix on the cable,for the width 35mm need to affix on the metals material, all need by 24H.测试方法: 宽度35mm的标签须粘贴在cable线上，宽度35mm的标签须贴在板