模具术语中英文.doc

模具术语中英文模芯 Parting Core 局部视图 Partial View 冷料井 Cold Slag 线切割 Wire E.D.M 轮廊 Contour 螺纹孔 Tapping Hole连接件 Fittings 斜针 Angle Pin 替换镶件Interchangeable Mold Inserts 水嘴接头Water Fittings 螺纹 Eyebolt Thread回针Stop Pin 二级顶出针 Sub-Leaderd Pin镶件Mold Insert唧嘴 Sprue 材料清单 Stock List手动滑块 Hand Slide流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action 装卸孔 Handling Hole 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位 Leader Pin Location水塞 Water Line Plug 撬模脚 Ppy Slot 配件 Components模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline压机 Press 晒纹 Texturing方铁Spacer Block 顶针板Ejector Plate顶针底板 Ejector Retainer Plate 垫板Retainer Plate 后模镶针 Core Pin拉圾钉Stop Pin 有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴 Extension Nozzle Bushing水口板导套 Runner Stripper Plate Bushing定位圈（法兰） Locating Ring 管钉（定位销） Dowel Pin管状管钉Tubular Dowel 吊环Safety Hoist Ring气顶 Air Poppet Valve 截水口镶件 Runner Shut-Off Insert缩水 Shrinkage 模胚 Mold Base下模镶件Core Block 上模镶件Cavity Block小镶件 Sub-Insert 下模小镶件 Core Sub-Insert上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert 压条Gib压紧块（铲机） Jaw 硬片（摩擦片） Wear Plate水口铁 Runner Bar 上模水口铁 Upper Runner Bar下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头 Support Pillar 直身锁 Side Lock斜度锁Interlock 锁模板 Safety Bar密封圈 ORing 喉塞Plug隔水片 Baffle 波子螺丝Ball-Catch斜顶Lifter 回针Return Pin 斜导柱Angle Pin推板Stripper Plate A板 APlateB板 BPlate 方铁 Spacer Block顶针板Ejector Plate 顶针底板 Ejector Retainer Plate合模 Shutoff导柱及导套Leader Pin Bushing 水口拉钩 Spuer Puller模框镶件Pocket Insert三板模 3-Plat Mold 分型面 Parting Line司筒 Ejector Sleeve 垫圈Washer熔接线（夹水纹） Weldline 吸针Sucker Pin回针板 Retainer Plate 顶出板 Knock -Out Plate公差Tolerance销针Dowel 钩槽Gib 精磨Finished 通框Through Window粘后模 Sticking Core 粘水口 Sticking Sprue夹水纹Weld Line 变形 Warpage漏水Water Leakage 刮花（擦伤） Galling漏电Ele Leakage 困气Air Trapping温度Temperature 注塑模Injection Mold入水 Gate 试板 Sampling压力Pressure 倒圆Fillet顶棍 Ejector 顶白Stress Mark粘前模Sticking Cav版本标识 Revision Level 材料清单Stock List斜导柱（斜边） Angle Pin 倒扣Under-Cut披峰Flash 缩水 Shrinkage氮化Nitride连续的Consecutive 分模面Parting Surface 擦位Shut-Off(S/0)加硬Harden 丝印Silkprint设计简图 Design Preliminary不干胶Adhesive Sticker 导向针 Guide Din公差Tolerance 线切割 Wire-Cut电火花Edm 抛光 Polishing蚀纹Texture 探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt油唧Hydraulic Cylinder 司筒Ejector Sleeve轮廓Contour 螺纹孔Tapping Hole连接件 Fittings 斜针Angle Pin接合Engage 替换镶件Interchangeable Mold Inserts水嘴接头 Water Fittings 螺纹Eyebolt Thread二级顶出针 Sub-Leader Pin 镶件 Mold Insert锁定位Lock 楔子(铲