各国插脚尺寸.doc

2PIN欧洲插脚Two-pin plugs for class II appliances (Up to 2.5 A rating) According to EN50075 - Standard Sheet and IEC60083 - Standard C5SymbolRequirement (mm)Measured (mm)SymbolRequirement (mm)Measured (mm)A 16.5IB25.6 - 26.6J 3.94 4.06C45 K 10.0 11.0DR 5.0 6.0L18.5 19.5E34.6 36.0M 90 F13.0 14.4N0.7 1.7GEngagement18.0 19.2O 2.0GEnd 17.0 18.0P 4.0HWithin 4 mm from engagement face 4.0mmQ 18.0Above 4 mm from engagement face 3.8mmA & P only for plug with supply cord. Direct plug-in product not consider the dimensions.英国插脚UK Plug Checking Form according to Figure 4 of BS1363-3Grounding pinSymbolRequirement (mm)Measured (mm)SymbolRequirement (mm)Measured (mm)A25.37 max.Q17.2-18.2B25.37 max.R6.22-6.48/C34.6 max.S3.90-4.05D11.05-11.18T6.22-6.48/E11.05-11.18U6.35 min. FR 15 min.-V60-80-GR 9.5 min.W1.35-1.85HR 9.5 min.X3.90-4.05I22.10-22.36Y1.2-2.0J22.23-23.23ZR 0.1-1.0-K1.35-1.85a58-62-L7.80-8.05b1.35-1.85M58-62-c58-62-N3.90-4.05/d1.35-1.85O9.2 max.e0.2 max.P9.5 max.f1.35-1.85澳规插脚Standard sheet Figure 2.1 (a1) or 2.1(c)Standard sheet Figure 2.1 (e) and fig 2.4PositionRequired (mm)By Measurement (mm)By the gauges in Figure A1A6.350.15-B6.350.15C-D7.92-PE10.31-PF17.060.4-G19.940.8121.9 max. or 27.0 min.-221.9 max. or 27.0 min.-321.9 max. or 27.0 min.-421.9 max. or 27.0 min.-560-P660-P78.6 min.-821.0 max.-920.01.0-101.0 max-118.70.5-Dimensions checked by gauge and measurementStandard sheet Figure 2.1 PositionRequired (mm)By Measurement (mm)By the gauges in Figure A1Plug type (h)R0.350.05-S0.90.1-T0.60-V6-P美国插脚Dimension Checking for Two-pin plugs of NA (15 A, 125 V) According to (NEMA WD 6-2002 Figure 1-15)SymbolRequirement (inch)Measured (inch)SymbolRequirement (inch)Measured (inch)A0.120 - 0.130E0.240 - 0.260B0.151- 0.161F0.307 - 0.322C0.449 - 0.479G0.055 - 0.065D0.625 - 0.718H0.495 - 0.505Perimeter faces to the plug blades shall not be less than 7.9 mm (intended for use with childrens toys) or 5.1 mm from any point of either blade中国插脚Dimension Checking for Tow-pin plugs (6 A, 10 A rating)According to Fig 1 of GB 1002-2008d SymbolRequirement (mm)Measured (mm)t1.40 1.50b6.18 6.40F12.565 12.835E15.65 16.35R5.00 7.00dThis distance of live plug to engage edge 6.5台湾插脚韩国插脚Dimension Checking for Korea plugs (Two-pole plug for 3A 250V)According to KSC 8305SymbolRequirement (mm)Measured (mm)SymbolRequirement (mm)Measured (mm)AMax. 90Q3.3 4.3BMax. 3RMin. 6CMax. f 2.5S25.6 26.6Df 36.0 f 37.0T13.0 14.4E18.8 19.2U18.8 19.2FR3.0 R3.3V34.6 36.0G3.5 4.5WR5 R6HMin. 5X45I31.5 32.5YMin. 4J9.9 10.1Z4K9.9 10.1A110.0 11.0LMin. 16.5B118.5 19.5MMin. 17.5C1f 4.74 f 4.86N18.5 19.5D1Max. 4.3OMin. 15.5E14.4 4.8Pf 4.74 f 4.86日本插脚Dimensions checked by gauge and measurementPositionRequired (mm)By Measurement (mm)A10.8C1.35 1.65D1.35 1.65E-F-G6.0 6.6H6.0 6.6I-J-K15.7 18.3L15.7 18.3M-N-O-P11.3 12.1Q11.3 12.1R2.8 3.3S3.5T 3 mm 14 mmSee aboveSee aboveSee aboveSee aboveSee aboveNote:1 The sketches are not intended to govern design, except as regards the dimensions shown2 Plugs can be rewirable or non-rewirableRequirements: The distance between the engagement face and the cord or cord guard, if any, shall be at least 14 mm Within this distance, the outline shall be not smaller than the engagement face. Within this distance, the outline shall be not larger than the engagement face. Insulating sleeves on the current-carrying pins are optional If the insulating sleeves are separate parts, they shall enter the plug by at least 3mm measured from the engagement face. The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins. To avoid damage to shutters, the ends of the pins shall show neither sharp edges nor burrs. They shall be of rounded shape as shown. The angle of 90 represents the maximum permissible area for the orientation of the entry of the flexible cable or cord.印度插脚：Indian Plug Checking WorksheetDimension: mmSymbolRated CurrentMeasured( ) 6A( ) 16AA22.220.1528.60.15B19.10.1525.40.15C7.010-7.0858.660-8.735D5.030-5.1057.010-7.085E15.77-16.9420.47-21.64F20.47-21.6428.47-29.64G1)7.949.52Note:1. “G” is the minimum distance between the pins and the periphery of the plug.阿根廷插脚：IRAM 2063 Plug (Class II, two-pole) Checking Worksheet（IRAM 2063：1982 + Amd 1999）SymbolRequirement (mm)Measured (mm)SymbolRequirement (mm)Measured (mm)A8.0 min.H1205B7.920.1I13.720.1C7.920.1J6.250.1D6.860.1K6.250.1E6.860.1L1.550.07F60M18.20.2G60NMarked “N”Yes / No沙特插脚：SASO Plug Checking Form according to Figure 1 of SASO 2203