QC 次品总结.doc

ELECTRONIC TOY (电子玩具) ABNORMAL SOUND 反常的声音即杂音 SHORT CIRCUIT 短路BATTERY/CONTACT SPRING EXPOSED 电池弹簧凸出 ELECTRIC LEAKAGE 漏电BATTERY/CONTACT SPRING COME OFF 电池弹簧脱落 BATTERY COIL OVER HEAT 电池线圈过热CONTACT PLATE RUST 电池片生锈 SWITCH POOR FUNCTION 开关功能不良CONTACT PLATE EXPOSED 电池片外露 SWITCH NON-FUNCTION 开关无功能CONTACT PLATE COME OFF 电池片脱落 CIRCUIT BOARD DAMAGED 电路板损坏CONTACT PLATE LOOSEN 池片松 CIRCUIT BOARD NON-FUNCTION 电路板无功能POOR CONTACT 接触不良 CIRCUIT BOARD LOOSEN电路板松POOR FUNCTION功能不良 POOR SOLDERING焊接不良INT NON-FUNCTION 间歇无功能COLD SOLDER假焊MAL-FUNCTION其中某一功能不良 NO SOUND WHEN SWITCH ON 按动后无声音NON-FUNCTION无功能 LIGHT ON CONSTANTLY灯长明SOUND TOO LOUD声音太大 MOTOR ON CONSTANTLY马达长期转动SOUND TOO LOW声音太小 DIFFICULT TO PRESS ON OR OFF按动困难NO SOUND无声音 BASE底座WEAK/NO LIGHT灯弱或不能发光 POOR不良WIRE EXPOSED电线外露 CONTACT 接触WIRE DETACHED电线甩脱 CIRCUIT 电路WIRE POOR WELDING电线焊接不良 SHAPE 形状REQUIREMENT要求SPRAYING/ TEMPO/PRINTING(喷油/移印)OVER SPRAY 飞油 MISSING PAINT/TEMPO 漏喷油/移印UNDER SPRAY 喷油不够 POOR PAINTING 喷油不良FOREIGN PAINT 外来油污 POOR TOUCH UP 补油不良SCRATCH PAINTING 刮花油 PAINT ABRASION 喷油擦花DUST PAINTING 油层沾尘BUBBLE PAINT 喷油起泡PAINT INSUFFICIENT COVERAGE 喷油薄,反底PAINT ACCUMULATED 聚油TEMPO PRINTING OFF SET 移印套色偏移 COLOR MIGRATION 摩擦脱色(转移)TEMPO PRINTING MISMATCH 移印不能互相吻合COLOR MISMATCH 颜色不配对PAINT SMEAR 油漆拖花(因拖模时过多的油由模边漏出) INCOMPLETE TEMPO PRINTING 移印部分缺油 DULL COLOR 哑色PAINT TEMPO DISCO CATE 喷油/移印移位PAINTING PEEL OFF 甩油ELECTRO - PLATING (电渡) POOR ELECTRO-PLATING电渡不良DULL ELECTRO-PLATING电渡哑色ELECTRO-PLATING PEEL OFF电渡脱落POOR HOT STAMP 热烫不良ELECTRO-PLATING YELLOWISH电渡变黄 OVER STAMP 热烫过多ELECTRO-PLATING ABRASION/SCRATCH 电渡擦花/刮花UNDER STAMP 热烫不足ELECTRO-PLATING SHADOW 电渡阴阳色 POOR SILK SCREEN PRINTING 丝印不良ELECTRO-PLATING BLACK MARK 电渡发黑OXIDATION氧化ELECTRO-PLATING RAINBOW 电渡成彩虹印 WRONG/MISSING PARTS错或漏配件GATE REMNANT 水口未清WRONG/MISSING LABEL 错或漏贴纸 FLASH 披条,披锋WRONG COLOR 颜色配错 GEAR SMOOTH 滑牙WRONG MATERIAL 配错原料 HALVES MISALIGNMENT 配件装配不对称WRONG ASSEMBle 装配错误SCREW RUST 螺丝生锈ABRASION MARK 擦花PLASTIC REMNANT 胶丝未消BURN MARK 烧焦 AIR BUBBLE 气泡CONTAMINATION MARK 杂色.混点 CRACKED 开裂MOTTLE MARK 斑点BROKEN 断裂CUT MARK 刀痕 DAMAGED 损坏SCRATCH MARK 刮痕 DEFORMED 变形DENT MARK 凹痕 DETACHED 脱落OIL MARK 油渍 EXPOSED 暴露FLOW MARK 夹水痕 POOR HOT MELTING 融合不良FOLD MARK 折痕 POOR HEAT STICKING 热贴不良GREASE MARK 机油印 POOR FLOCKING 搪胶植毛不良EJECTOR MARK 顶针痕 POOR FUNCTION 功能不良DIRT MARK 污渍 POOR ROTOCASTING 搪胶不良GLUE MARK 胶水渍 POOR DIE-CAST 合金压炼不良NEST MAEK 超声压花 POOR TRANSPARENCY 透明度不良SOLVENT MARK 熔剂印 GAP ON X X XXXX (位置)离罅STRESS MARK 顶白 POOR SONIC WELD 超声不良WATER MARK 水印 POOR ASSEMBLY 装配不良WHITE MARK 发白 NON-FUNCTION 无功能GASSING 胶水毒气味 CANNOT HOLD POSITION不能定位SHORT SHOT走料不到 CLAMP MARK 钳印SHRINKAGE 缩水 GOLD MARK 合金有冷纹WARPAGE 变形SINK WARK 凹印CANNOT MOVE 不能移动/活动MOISTURE MARK 水气STRING CANT RETRACE 绳子不能回复ELASTIC 橡筋SHAFT 铁轴 ,杆状物RIVET 铆钉, (v:固定)AXLE 车轴 MISALIGNMENT 不一至MISSILE CANT HOLD POSITION 飞弹不能扣住WHEEL CANNOT ROLL FREELY 轮不能顺转INT-FUNCTION = INTERMITTENT NON-FUNCTION间歇性无功能 LAUNCHER CANT FIRE MISSILE 发射器不能发射飞弹 MISSILE CANT INSERT IN TO LAUNCHER 飞弹不能插入发射器中 MISSING PARTS漏装配件 J-HOOK DAMAGED挂钩烂MISSING INSTRUCTION SHEET/BOOK漏装说明书/书仔J-HOOK WRINKLE 挂钩破MISSING DATE CODE 漏印日期 J-HOOK POOR DIE-CUT挂钩剪裁不良MISSING WHOLE PACK OF ACCESSORY漏装整包配件J-HOOK STICKER DISLOCATED 挂钩胶贴移位WRONG PACKAGING 错包装 J HOOK STICKER EXPOSED 挂钩胶贴凸起PACKAGING DAMAGED 包装损坏 WINDOW BOX FILM DAMAGED 彩盒胶窗烂PACKING WRINKLED 包装皱 WINDOW SHEET STRESS 彩盒胶窗顶白CARTON MARK ILLEGIBLE 箱印模糊 WINDOW SHEET DETACHED 彩盒胶窗甩脱GIFT BOX ILLEGIBLE 彩盒印刷模糊WINDOW SHEET POOR SEALING 彩盒胶窗黏合不良 STORY BOOK ILLEGIBLE 故事书印刷模糊WINDOW SHEET NOT TRANSPARENT ENOUGH 彩盒胶窗透明度不良 INSTRUCTION SHEET ILLEGIBLE 说明书印刷模糊 BLISTER CARD ILLEGIBLE 吸塑卡印刷模糊WHITE MARK ON WINDOW SHEET 彩盒胶窗发白DATE CODE ILLEGIBLE日期印刷模糊 DENT MARK ON WINDOW SHEET彩盒胶窗有凹印BLISTER POORHEATSEALING 吸塑热封不良 GIFT BOX SEAL OPEN 彩盒缝口爆开BLISTER UNSEAL/DETACH 吸塑未封口/甩掉 GIFT BOX CRUSHED 彩盒压烂或压破INCORRECT BLISTER 吸塑不正确 GIFT BOX DEFORMED 彩盒变形BLISTER DAMAGED 吸塑烂GIFT BOX WET 彩盒湿BURNT MARK ON BLISTER 吸塑烧焦 GIFT BOX UNSEAL 彩盒未封口BLISTER CRACK 吸塑裂 GIFT BOX CRUMPLE 彩盒弄破BLISTER CRUSHED 吸塑压破 FOLD MARK ON GIFT BOX 彩盒有折痕BLISTER DEFORMED 吸塑变形 TAPE POOR STICKING 胶纸黏合不良BLISTER DETACHED 吸塑甩脱 INSECT INSIDE PACKAGE 包装内有昆虫BLISTER SHRINKAGE 吸塑缩水 FOREIGN MATERIAL INSIDE包装内有杂物BLISTER UNDERSHOT 吸塑走料不足 HUMAN HAIR INSIDE PACKAGE 包装内有头发INCORRECT BLISTER CARD吸塑卡用错 SOLID PACK独立装FOLD MARK ON BLISTER CARD 有折痕 BULK PACK散装(胶袋装)OUTFIT SEALED ON BLISTER公仔衫夹于吸塑中ASSORTMENT PACK 混装BLISTER CARD WET 吸塑卡湿 INSERT内托BURNTMARK ON BLISTER CARD吸塑卡有烧焦痕EURO HOLE欧洲(飞机)孔BLISTER CARD DELIMITATION吸塑卡纸内层分离J HOOK 丁字型挂钩BLISTER POOR DIE-CUT吸塑剪裁不良BUTTER-FLY HOLE 蝴蝶孔BLISTER CARD WRONG DIE-CUT 吸塑剪裁错误CABEL TIE (内有小铁线的)扎带 BLISTER CARD WRINKLE吸塑卡破PLASTIE胶扎带BLISTER CARD DAMAGED吸塑卡烂BILINGUAL PACKAGE 两种语言包装LABEL PEEL OFF贴纸翘起 TRILINGUAL PACKAGE 三种语言包装BLISTER CANNOT STAND PROPERLY 吸塑不能完全站立 MASTER CARTON 外纸箱POLYBAG DAMAGED 胶袋烂或穿孔INNER CARTON 外纸箱POLYBAG POOR DIE-CUT 胶袋剪裁不良BLISTER 吸塑MISSING VENT HOLES ON POLYBAG胶袋漏打出气孔 CARD 咭纸POLYBAG NOT SEALED/TAPED 胶袋未封口 GIFT BOX 彩盒POLYBAG TOO THIN 胶袋太薄NET WEIGTH 凈重INCORRECT POLYBAG 胶袋不对 GROSS WEIGHT 毛重DATE CODE 日期印 FRONT / REAR 前 / 后SHIPMENT IN STD GTI PACKAGE 货物为标准LEFT . RIGHT左 . 右TOP . BOTTOM顶 . 底WITH OUT 没有 SOFT TOY (车缝及充棉玩具) YARN RUN 走纱 STUFFING EXPOSE 棉外露 EYE TUTED 眼倾斜 POOR FACE SHAPE 脸部不对称UNEVEN ON EYE 眼睛不对称 COLOR DEVIATION 颜色有差别POOR SEWING 车缝不良 STITCHING HOLE 针孔FARYED EDGED 散口 OVER/UNDER STUFFING 入棉过多/少NO BACK TACK 无回针UNEVEN STUFFING 入棉不均匀POOR HAND STITCHING 手缝不良 SEWING MACHINERY MARK 衣车靴痕SEAM OPEN 爆线口 FABRIC TESTIER MISMATCH 布纹不对齐JUMPING STITCHES 跳针MATERIAL TORN (物料)烂LOW/HIGH DENSE STITCH 车缝太疏密MISSING/POOR MIRRORING 漏集骨/集骨不良SEAM-ALLOWANCE EXPOSE 子口外露UNT