810S跟踪器说明书_ce.doc

810S小型GPS车辆追踪器使 用 说 明一设备介绍810S车辆追踪器是一种由GPS模组和GSM/GPRS模组组成的车辆远程定位追踪装置，是一种体积小巧、高度隐蔽、高精确度的设备。本追踪器可以提供GPS卫星定位信息，也可以在无GPS卫星信息的情况下提供GSM基站的辅助定位信息，可以发送经纬度坐标信息到系统平台和授权手机。您可以利用这些功能来定位管理自己的车辆。1、 外形按键及外部接线定义继电器（黄色），ACC（绿色）2、安装SIM卡在追踪器上有一个SIM卡插口，按照胶塞上的指示方向将SIM卡插入机器。备注：SIM卡的类型是GSM卡（建议选用中国移动的SIM卡）确保SIM卡上有足够的金额，以便支付通讯费。确保SIM卡已开通来电显示及收发短信息功能，如需要使用服务平台实时跟踪和短信定位，还需要开通GPRS功能3设备接线事项1电源、ACC、继电器（4PIN）1） 本设备标准供电为9V-49V DC，请选用原厂提供的电源线，红色线为电源正极，黑色为电源负极；安装负极请选择单独接地或搭铁，勿与其他地线共接；2）ACC线（绿色）接车辆的ACC开关。请务必接上ACC线，追踪器将依据ACC状态来决定是否进入设防状态；若不接ACC线，会使车辆一直处于设防或者休眠状态。在设防或者休眠状态下如果车辆发生震动，将会触发震动报警。若不需要防盗报警功能可将ACC线直接与电源正极并接，一直维持高电平。4特殊功能说明1）设防功能：如果ACC线接到车的ACC开关，车钥匙关闭后5分钟之后自动开始设防，如一分钟内车辆发生震动，每震动一次则延长一分钟时间进入设防状态，直至一分钟内完全没有发生震动，进入设防状态。2）休眠模式：进入设防状态后，如果20分钟内无振动，本设备就进入休眠模式。在休眠模式下，本设备不定位，不上传数据，但可以收发短信，打接电话，以达到节电目的。3）震动报警：在设防状态下（包括休眠状态），车辆发生震动，本设备立即断开继电器并拨打车主电话报警，同时唤醒GPS 定位，并将报警及位置数据信息上传到平台。5、指示灯定义：红灯（ ）表示GPS状态状态含意间隔1秒闪GPS无信号间隔4秒闪GPS正常定位蓝灯（ ）表示GSM/GPRS信号状态:状态含意10秒闪一次与服务器连接正常上传数据4秒闪一次GSM正常待机状态1秒闪一次没有GSM 信号/ 初始化/通话/来电6使用环境工作温度-20-65湿度5%-95%尺寸（mm）90*53*21输入电压9V49V待机平均电流小于80MA二短信定位用任意手机发送短信9880000到终端，终端立刻返回一条位置信息到查询手机。三全球定位平台查询终端出厂默认平台查询功能为开启状态，默认平台地址是：，上传间隔为60秒一次。备注：如果需要更改平台地址和上传间隔，请参考附录中的803,730指令。平台地址：用户名：机器后边的IMEI号码(或运营商直接提供)默认密码：123456。提示：该功能实现需要网络运营商支持，SIM卡需开通GPRS功能。四配件描述（1）电源线 继电器（黄色）ACC（绿色）电源正极（红色）电源负极（黑色）（2）SOS按键(选配) （3）MIC（选配） （4）继电器（选配）附录一 指令一览表指令(0000代表用户密码，可以修改)说明#710#中心号码#0000#设置中心号码通过手机以短信方式设置中心号码。设置成功后，该手机会收到终端返回的“&710&设置成功&”信息。例如：#710#134xxxxxxxx#0000#说明： SOS报警，低电压报警信息均返回到该号码上。#711#号码1#号码2#号码3#0000设置预存号码通过手机短信发送设置指令到终端。设置成功后，发送短信手机会收到终端返回的“&711&设置成功&”回复信息。例1：#711#134xxxxxxxx#0000#（只设置一个预存号码的格式）例2：#711#134xxxxxxxx#158xxxxxxxx#150xxxxxxxx#0000#（设置3个预存号码的格式） 6660000单次位置查询，返回一条经纬度信息9880000单次位置查询，返回一条具体的位置信息9990000单次位置查询，返回一条Google链接网址信息5550000监听功能监护人发送短信指令“5550000（0000是用户密码）”到卡片机。卡片机收到指令后，回拨发送该条指令的号码。电话接通后，卡片机进入监听模式。注：只要设置了预存号码和中心号码，监听功能才有作用。中心号码设置请参考指令集内710设置格式，预存号码设置请参考指令集内711指令设置格式。#567#年月日#时分秒#0000#时间设置指令例：#567#110513#125820#0000#用户可发送该指令修改按键报时的时间#730#取样间隔（0或15-65535秒）#上传条数（0-10条）#0000#设置正常定时上传数据本产品出厂默认上传间隔为30，定时上传功能开启。用户可以根据自己的需求更改该参数。 例如：#730#20#4#0000#说明：参数20表示20秒取点一次，累计4次取点后上传一次定位信息，上传间隔为20*4=80秒。客户根据自己需求更改该参数即可。注意：用户也可发送#730#0#1#0000#，关闭GPRS，进入省电模式。#770#用户新密码(4位)#用户旧密码(4位)#更改用户密码说明:执行该指令终端将用户密码根据用户需求进行改变。设置成功后终端向设置手机回复“&770&设置成功&”，密码错误时回复“&770&密码错误&”。例如：#770#1111#0000#。执行该指令后，用户密码由0000变为1111。#801#字母或数字(0-20位)#0000#更改用户名功能说明：执行该指令后，终端在GPRS方式下的用户名根据要求被设定。设置成功后，向设置手机发送短信“&801&设置成功&”，密码错误时返回“&801&密码错误&”。 例：#8010000#802#APN(字母或数字0-32位)#登录用户名(字母或数字0-20位)#登录密码(字母或数字0-20位)#0000#设置APN接入点说明：执行该指令后，终端在GPRS方式下的使用的APN根据要求被设定。设置成功后终端向设置手机回复“&802&设置成功&”，密码错误时回复“&802&密码错误&”。例1: #802#CMNET#0000#。执行该指令后，终端APN为CMNET，用户名，密码都为空。例2:#802#CCDLEN#Guest#Guest#0000#。执行该指令后：APN为CCDLEN，登录用户名为：Guest,登录密码为：Guest。注意：本产品默认的APN为CMNET。#803#固定IP地址#端口号#0000#设置服务器地址该指令用于设置GPRS中心服务器地址。服务器地址可以是固定IP值，格式为：xxx.xxx.xxx.xxx；也可以是域名，长度小于64字节。设置成功后，向设置手机发送短信“&803&设置成功&”，密码错误时返回“&803&密码错误&”。例如：#803#48#30000#0000#或通过域名设置, 例如：#803##30000#0000#注：本产品出厂时已有默认的服务器地址，设置服务器地址的指令请慎用。# 751#围栏半径（米）#取样间隔（分钟）#纬度#经度#0000#设置电子围栏例如：#751#500#5#22.5442N#113.91E#0000#或者#751#500#5#22.5442S#113.91W#0000#设置成功后，向设置手机发送短信“&751&设置成功&”。 终端每次离开这个区域都会发送出围栏报警信息到中心号码。说明：N表示北纬，S表示南纬，E表示东经，W表示西经。N/S,E/W是该指令的必需条件。# 752#0000#读取电子围栏向终端发送指令：#752 #用户密码4位#，指令发送成功后终端读取模块围栏工作状态的数据，返回到发送手机。密码错误时回复“&752&密码错误&”。例如：#752#0000#返回：#open:1#lat:22.543685N#lng:113.910633E#distance:500#time:5#status:2或者#open:1#lat:22.543685S#lng:113.910633W#distance:500#time:5#status:2其中：open:1为围栏开启，open:0为围栏关闭。 lat: 22.543685N，北纬； 22.543685S，南纬。 Lng: 113.910633E，东经； 113.910633W，西经。 distance:500，围栏半径。 time:5，采样间隔时间。 status:2终端获取了有效卫星数据，围栏工作正常。 status:1围栏开启但终端没有得到有效地卫星数据。 status:0没有设置电子围栏。# 760#0000#取消电子围栏2230000启动断油电指令2330000关闭断油电指令#901# 读取用户参数发送该指令后，终端返回信息：#中心号码#密码#用户名称#用户密码#预设号码1#预设号码2#预设号码3#号码4#IMEI号#例如：#134xxxxxxxx#00000000#134xxxxxxxx #356823032080264#902# 读取GPRS参数#模式#取样时间#取样条数APN#APN用户名#APN密码#IP#端口#版本号例如：e.g.:#5#0#0CMNET#48#30000#2014/09/25 10:36 810_60D_SW_11#920#0000#语音切换指令 发送该指令后，终端可在中、英文进行切换。#110#0000#打开/关闭报警信息（停车报警，超速报警，震动报警，拐弯报警等），不包含剪线报警，出围栏报警，低电压报警。默认是关闭,发送成功后启动报警功能；再次发送成功后关闭报警功能。#320#0000#里程清零指令#330#0#0000#关闭里程统计指令#330#1#0000#打开里程统计指令附录二 短信信息短信格式说明IMEI号：SOS紧急求救（经纬度信息或基站信息）SOS紧急求救信息IMEI号：终端电池电量低，请及时充电低电压报警信息IMEI号：已出围栏（经纬度信息）出围栏信息震动报警机器进入休眠模式后，ACC未接电，但车被移动，机器便会给SOS号码手机发出震动报警信息。剪线报警当机器主电源线被断开，机器便会像SOS号码发出剪线报警信息。注意事项：本设备为非防水设计，请务必配备防水包；本设备须与GSM网络配套工作；请确保SIM卡上有足够的余额以免引起使用上的不便；本设备在断电状态和服务区外无法工作，即使是注册用户；本设备支持GPS和GSM/GPRS双重定位方式，视同GPS定位结果；请在合法领域使用本设备。任何违反法律的后果将有使用者自行承担。810S Mini GPS Vehicle TrackerUser Manual Equipment IntroductionThis 810S vehicle tracker is a remote vehicle positioning device consisting of a GPS module and a GSM/GPRS module, which is featured by compact size, good concealment and high precision. It can provide the GPS satellite positioning information, and can also provide the positioning information supported by the GSM base station if the GPS satellite information is unavailable, and the information about the latitude and longitude coordinates can be sent to the system platform and the preset mobile phone number. You can make use of these features to locate and manage your vehicle.1. Definition of buttons and external wiring2. Installation of SIM cardThere is a SIM card slot on the vehicle tracker. Insert the SIM card into the slot。Note: The SIM card shall be GSM card. Make sure to keep enough money in the SIM card account. Make sure the Caller ID Display function and SMS service of the SIM card have been subscribed for. To use the real-time tracking by service platform and positioning by SMS, the user has to subscribe for the GPRS service.3. Wiring precautions1. Power supply, ACC, relay (4-PIN)1) The standard power supply of the equipment is 9V-49V DC. Please use the factory supplied power cord, the red wire is the positive wire, and the black wire is the negative wire. When connecting the negative wire, please ground it separately, and do not connect it to other ground wires;2) ACC wire (green) is used to connect to the vehicle ACC switch. Be sure to connect the ACC wire, because the vehicle tracker will decide whether to enter the security status depending on the ACC switch status; if the ACC wire is not connected, the vehicle will be kept in the security or sleep status. Under the status of security or sleep, if vehicle vibration occurs, the vibration alarm will be triggered. If anti-theft alarm function is not required, you can connect the ACC wire with the positive wire in parallel to maintain high electrical level.4. Description of special functions1) Security functionIf the ACC wire is connected to the ACC switch, this equipment will start the security function automatically in five minutes after the vehicle engine is turned off. If vehicle vibration occurs within one minute, the equipment will enter the security status with 1 minute delay, and will enter the security status unless no vehicle vibration occurs.2) Sleep modeAfter entering the security status, if no vehicle vibration occurs within 20 minutes, this equipment enters the sleep mode. In the sleep mode, this equipment neither locates nor uploads data, but can send/receive messages and make/answer calls, so as to achieve maximum energy saving.3) Vibration alarmUnder the security status (including the sleep status), if vehicle vibration occurs, this equipment immediately disconnects the relay and dials the mobile phone number of the vehicle owner to give an alarm; meanwhile, it wakes up the GPS positioning, and uploads the alarm and location data to the service platform.5. Definition of indicatorsRed indicator () refers to the GPS statusStatusMeaningFlash at intervals of 1 secondNo GPS signalFlash at intervals of 4 secondsGPS normal positioningBlue indicator () refers to the GSM/GPRS signal statusStatusMeaningFlash evey 10 secondsNormal connection to the server for data uploadingFlash evey 4 secondsGSM normal standby statusFlash evey 1 secondNo GSM signal/initialization/call in progress/incoming call6. Operating environmentFrequencyGSM/GPRS 850/900/1800/1900MHz; GPS1575MHzOperating temperature-20-65Humidity5%-95%Dimensions (mm)90*53*21Input voltage9V 49VAverage current in standby modeLess than 80MAII. Query by SMSSend the message 9880000 to the terminal using a mobile phone, and then the terminal will return a message about the locationIII. Query by Global Positioning Service PlatformThe factory-set platform query function of the terminal is on, and the default platform address is , and the uploading interval is 60 seconds.Note: If you need to change the platform address and the uploading interval, please refer to the 830 and 730 instructions described in the annex respectively.Platform address: User name: IMEI number at the back of the equipment (or directly provided by the operator)Default password: 123456Note: This function requires the support from the network operator, and the GPRS function of your SIM card has to be subscribed for.VI. Description of Accessories(1) Power cord(2) SOS button (optional) (3) MIC (optional) (4) Relay (optional)Annex I Instruction SetInstruction（0000 is user password, it can be modified）Description#710#center number#0000 #Set the center number.Set the center number through the message sent by a mobile phone. After successful setting, the terminal returns “&710&Config OK&”.e.g.: #710#134xxxxxxxx#0000#Description: The SOS alarm and low battery alarm messages will be returned to the number.#711#phone number 1#phone number 2 #phone number 3#0000#Set a preset numberUse a mobile phone to send the setting instruction to the terminal. After successful setting, the mobile phone will receive the message “&711&CONFIG OK&” returned by the terminal.e.g. 1: #711#134xxxxxxxx#0000# (The format of setting one preset number)e.g. 2: #711#134xxxxxxxx#158xxxxxxxx#150xxxxxxxx#0000# (The format of setting three preset numbers)6660000Single location query; a message about the latitude and longitude will be returned9880000Single location query; a message about the specific location will be returned.9990000Single location query; a message about the Google website will be returned.5550000Monitoring functionThe guardian uses a mobile phone to send the message instruction “5550000 (0000 is the user password)” to the vehicle tracker. Upon receipt of the instruction, the vehicle tracker dials the number of the mobile phone which has sent the message instruction. After the call is connected, the vehicle tracker enters the monitoring mode.Note: The monitoring function can be used only when a preset number and the center number are set. For the center number setting and the preset number setting, please refer to the 710 and 711 instruction setting formats described in the Instruction Set respectively.#567#year, month, day#hour, minute, second #0000#Time setting instructione.g.: #567#110513#125820#0000#Through sending this instruction, the user can change the one-key time announcement.#730#sampling interval (0 or 15-65535 seconds)#number of pieces of data uploaded (0 -10)#0000#Set the timed data uploading functionThe factory-set uploading interval of the product is 30, and under this circumstance, the timed uploading function is turned on. The user can change the parameter according to his needs.e.g.: #730#20#4#0000#Description: “20” refers to point sampling every 20 seconds, and the positioning information will be uploaded after point sampling 4 times, that is, the uploading interval is 20*4=80 seconds. The user can change the parameter according to his needs.Note: The user can send the instruction #730#0#1#0000# to turn off the GPRS, so as to enter the power saving mode.#770#new password (4 digits) #old password (4 digits)#Change the user passwordDescription: After the instruction is executed, the terminal will change the user password according to the users requirements. After successful setting, “&770&CONFIG OK&” will be returned to the phone; if the password is wrong, “&770&PASSWORD ER&” will be returned.e.g.: #770#1111#0000#. After the instruction is executed, the user password changes from 0000 to 1111.#801#letters or numbers (0-20 digits)#0000#Change the user nameDescription: After the instruction is executed, the user name of the terminal under the GPRS mode will be set according to the requirements. After successful setting, “&801&CONFIG OK&” will be returned to the phone; if the password is wrong, “&801&PASSWORD ER&” will be returned.e.g.: #8010000#802#APN (letters or numbers, 0-32 digits)#login user name (letters or numbers, 0-20 digits)#login password (letters or numbers, 0-20 digits)#0000#Set the APNDescription: After the instruction is executed, the terminal APN under the GPRS mode will be set according to the requirements. After successful setting, “&802&CONFIG OK&” will be returned to the phone; if the password is wrong, “&802&PASSWORD ER&” will be returned.e.g. 1: #802#CMNET#0000#. After the instruction is executed, the terminal APN is CMNET, the login user name and password are blank.e.g. 2: #802#CCDLEN#Guest#Guest#0000#. After the instruction is executed, the APN is CCDLEN, the login user name is Guest and the login password is Guest.Note: The default APN of this product is CMNET.#803#fixed IP address#port number#0000#Set the service addressThis instruction is used to set the GPRS center server address. The server address can either be a fixed IP, whose format is xxx.xxx.xxx.xxx; or a domain name, whose length is less than 64 bytes. After successful setting, “&803&Config OK&” will be returned to the phone; if the password is wrong, “&803&Password Error&” will be returned.e.g.: #803#48#30000#0000#or it can also be set through the domain name:e.g.: #803#jzdw.GPS99.net#30000#0000#Note: This product has a factory-set server address, and the server address setting instruction shall be used with caution.#751#fence radius (meter)#sampling interval (minute)#latitude#longitude#0000#Set the electronic fencee.g.: #751#500#5#22.5442N#113.91E#0000# or#751#500#5#22.5442S#113.91W#0000#After successful setting, “&751&CONFIG OK&” will be returned to the phone. When the terminal leaves the area, the fence alarm message will be sent to the center number.Description: N refers to north latitude, S refers to south latitude, E refers to east longitude, and W refers west longitude. N/S, E/W is the necessary condition of the instruction.#752#0000#Read the electronic fenceSend the instruction “#752#4-digit user password#” to the terminal. After the instruction is successfully sent, the terminal reads the work status data of the fence and returns it to the phone. If the password is wrong, “&752& PASSWORD ER &” will be returned.e.g.: #752#0000#The following will be returned:#open:1#lat:22.543685N#lng:113.910633E#distance:500#time:5#status:2Or#open:1#lat:22.543685S#lng:113.910633W#distance:500#time:5#status:2Wherein, open:1 refers to the activation of the fence, open:0 refers to the deactivation of the fence.lat: 22.543685N refers to north latitude, 22.543685S refers to south latitude.lng: 113.910633E refers to east longitude, 113.910633W refers to west longitudedistance: 500 refers to the radius of the fence.time:5 refers to the sampling interval.status:2 refers to that the terminal gets valid satellite data, and the fence works normally.status:1 refers to that the fence is activated, but the terminal fails to get valid satellite data.status:0 refers to that the electronic fence is not set.#760#0000#Cancel the electronic fence2230000Turn on the fuel/power cut-off function2330000Turn off the fuel/power cut-off function#901# Read the user parametersAfter the instruction is sent, the terminal returns the following message:#center number#password#user name#user password#preset number 1# preset number 2#preset number 3# preset number 4#IMEI number#e.g.:#134xxxxxxxx#00000000#134xxxxxxxx #356823032080264#902#Read the GPRS parameters#mode#sampling time#number of samplesAPN#APN user name#APN password#IP#port#version numbere.g.:#5#0#0CMNET#48#30000#2014/09/25 10:36 810_60D_SW_11#904#GPRS connection #905#GPRS disconnection#920#0000#Voice switching instructionAfter the instruction is sent, the terminal can switch between English and Chinese#110#0000#Turn on/off alarm function include Stop alar