巴西插头尺寸标准.pdf_第1页
巴西插头尺寸标准.pdf_第2页
巴西插头尺寸标准.pdf_第3页
巴西插头尺寸标准.pdf_第4页
全文预览已结束

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

Earthing pin and optional construction for the contact pins Engagement face No sharp edge Note 1 See key page 12 2 The sketches are not intended to govern design except as regards the dimensions shown 3 Plugs can be rewirable or non rewirable Figure 7 2 poles with earthing contact for class I equipment 10A 250V Key of page 12 1 The earthing terminal shall be indicated by the symbol Indication of the other terminals is optional The indications shall be placed inside the body near the terminals There is no need to mark the terminals of non rewirable types 2 The distance between the engagement face and the cord or cord guard if any shall be at least 14 mm Compliance is checked by means of the acceptance gauge under consideration 3 Within this distance the outline shall be not smaller than the engagement face 4 Within this distance the outline shall be not larger than the engagement face 5 Insulating sleeves on the current carrying pins are optional If the insulating sleeves are separate parts they shall enter the plug by at least 3mm measured from the engagement face 6 The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins 7 To avoid damage to shutters the ends of the pins shall show neither sharp edges nor burrs They shall be of rounded shape as shown 8 The angle of 90 represents the maximum permissible area for the orientation of the entry of the flexible cable or cord Optional construction without the insulating sleeves Engagement face Note 1 See key page 20 2 The sketches are not intended to govern design except as regards the dimensions shown 3 Plugs can be rewirable or non rewirable Figure 13 2 poles without earthing contact for class II equipment 10A 250V No sharp edge Key of page 20 1 The distance between the engagement face and the cord or cord guard if any shall be at least 14 mm 2 Within this distance the outline shall be not smaller than the engagement face 3 Within this distance the outline shall be not larger than the engagement face 4 Insulating sleeves on the current carrying pins are optional If the insulating sleeves are separate parts they shall enter the plug by at least 3mm measured from the engagement face 5 The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins 6 To avoid damage to shutters the ends of the pins shall show neither sharp edges nor burrs They shall be of rounded shape

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论