钠离子交换器.doc

三、钠离子交换器Sodium ion exchanger1说明无顶压逆流再生钠离子交换器具有逆流再生的一切优点，并省去了顶压系统，简化了操作，节省了投资及运行费用。因此是目前软化水中最先进的设备。1 and instructionsNo pressure sodium ion exchange counter-flow has all the advantages of counter-flow omitted, and high pressure system and simplify the operation, save investment and running costs. So is the most advanced equipment, water softening.2、 技术标准 无顶压逆流再生钠离子交换器为焊接碳钢结构的园柱形容器，顶部和底部为椭圆型封头，设备按标准进行设计、制造和试验，所涉及的标准详见执行标准表。 阳床本体内部衬胶厚度为4.5mm，接管衬胶到各法兰的密封面。设备内部的其它需防腐的非衬胶件材质为316L不锈钢材质。 钠离子交换器内装设上部配水装置、底部集水装置、底部出水装置、中间排再生液装置和其附件。上部配水装置为头式结构,采用316L不锈钢丝绕管大喷头布水方式、底部出水装置均采用孔板及排水帽的配水方式,水帽为塔式结构,材质为ABS,水帽缝隙为0.25mm,底部出水装置为挡水板结构。底多孔板与下封头间采用无缝管加强,加强管共设3套。 钠离子交换器内的配水和集水装置，保证整个树脂层水流均匀，防止偏流。底部排水帽的布置呈菱形排列,排水由的设置按最大运行流速进行设计,并留有一定的余量。中间排水装置采用支母管型式，支管为梯形不锈钢绕丝管内镶不锈钢钻孔管,材质为316L，支管绕丝缝隙宽度为0.25mm。 钠离子交换器的外部本体管路(一次阀门前)为衬胶管,衬胶厚度为3mm,底部出水管配有法兰仪表接口。每台钠离子交换器配有2个标准的F500mm旋吊式侧人孔及一个底部人孔。人孔盖内表面和器壁内表面持平。人孔配有人孔盖、垫圈、螺栓、螺母和起吊杆等全套部件。每台钠离子交换器配有两对窥视孔，分别用于观察正常运行时的树脂层和反洗时的树脂层高度。窥视镜12cm宽、37cm高，视镜材质是透明、耐腐蚀并有足够的强度以承受来自交换器内部的压力的有机玻璃。窥视孔法兰内表面和器壁内表面持平。 每台阳床侧壁留有两个输送树脂的法兰接口。 每台钠离子交换器配有进水阀、出水阀、反洗进水阀、反洗排水阀、小反洗进水阀、正洗排水阀、再生液进口阀、再生液出口阀和排空气阀等。其它附件及材质:进水取样管: 材质:1Cr18Ni9Ti进水取样阀: 材质:1Cr18Ni9Ti出水取样管: 材质:1Cr18Ni9Ti出水取样阀: 材质:1Cr18Ni9Ti压力表: 耐腐蚀钠离子交换器的内部件在工厂安装定位，并提供正确的安全支撑，以防止运输时的偏位、松动及损坏。2, the technical standard1 no pressure counter-flow natrium ion exchanger for welding of steel structure column container garden, top and bottom for elliptic sealing head, according to standard equipment design, manufacturing and testing, involved in implementation of standard meter standard.2.Yang (internal lining rubber thickness bed ontology to 4.5 mm, rubber lining to each flange friction. The other anticorrosive equipment within the lining rubber parts for 316L stainless steel material qualitative.3.Sodium ion exchanger (upper installed within a water device, bottom bottom water catchment device, liquid regeneration device, the middle line and its attachments. The water head type structure for using 316L stainless steel wire, big round pipe nozzle cloth of water, water device adopts hole bottom plate and the water drainage cap, water tower structure, material for cap for ABS, water cap for 0.25 mm, bottom aperture for water retaining water board structure.4 and the porous plate between head adopts the seamless tube, strengthen tube of strengthening 3 sets.5 within the natrium ion exchanger with water and water device, guarantee the resin layer, prevent water drift. At the bottom of a diamond drainage cap, drainage arrangement by setting design according to the maximum operating velocity, and certain allowance. By middle drainage tube type, a mother to trapezoidal stainless steel pipe with stainless steel round wire inside drill pipe, the material of 316L, pipe around for 0.25 mm crack width of silk.6 sodium ion exchanger external ontology pipe (a) for lining hose before valve, lining rubber thickness of bottom, with a conduit 3mm flange instrument interface. Each sodium ion exchanger with 2 standard ? 500mm spin hanging side manhole and a bottom manholes. Within the manhole covers the wall surface and inner surface. Manholes are equipped with manhole covers, gasket, bolts, nuts and suspenders and complete parts.7 each sodium ion exchanger with two of the peephole, during normal operation, to observe the resin layer and the height of the resin layer when washing. 37cm 12cm wide, high sighting glass is transparent qualitative, depending on the mirror, corrosion and of sufficient strength to withstand the pressure switch from inside the organic glass. The peephole flange surface and the wall inside surface.8. Yang bed wall) each flange resin with two transport interface.9 each natrium ion exchanger with water inlet valve, valve, backwashing inlet valve, the drain valve, small reverse wash washing water drain valve disc, was washed, import valve, liquid and emptying valve outlet valve liquid etc. other attachments and material: Water sampling tubes: material: 1Cr18Ni9TiSample inlet valve: material: 1Cr18Ni9TiWater sampling tubes: material: 1Cr18Ni9TiWater sampling valve: material: 1Cr18Ni9TiPressure gauge, corrosion resistanceSodium ion exchanger internal parts in the factory, and provide the correct installation of safety, in order to prevent the transportation of partial, loosening and damage.3、技术参数表:序号名 称主 要 技 术 参 数1设备型号LNN-1402型式立式圆形容器3数量2台4正常流速15m/h5正常流量20m3/h6设备直径/封头直径1420/1416 mm7直段高度/总高度3400/4960mm8配套树脂9-层高1800mm+200mm10-树脂牌号732#11-产地杭州(漂莱特)争光树脂厂12衬胶13-衬胶牌号/层数1751#/2层14-衬胶厚度/胶层硫化方式4.5mm/蒸汽硫化15-胶层电火花试验1.5万伏16设计压力/试验压力0.6/0.75MPa17设计温度4-50C18筒体/封头制作材料Q235-A/Q235-A19筒体厚度/封头厚度8mm/10mm20多孔板直径/厚度/材质1400/18mm/Q235-A21排水帽规格/数量/单个产水量90/70个/(1t/h)22排水帽材质/缝隙间距ABS/0.25mm23多孔板支撑管数量/规格/材质6套/894/Q235-A24顶部进水装置型式/材料梯形丝绕管大喷头式/316L不锈钢25中间排水型式/材料梯形丝绕子母管式/316L不锈钢26中排丝绕管缝隙0.25mm27人孔型式/数量旋吊人孔/2个28人孔数量/尺寸2个/DN500,PN0.629本体管道尺寸/连接方式1084/法兰30窥视孔数量/尺寸2 个/ 350120 mm31窥视孔视镜材料/厚度有机玻璃/20mm32进水阀型号/规格G41J-10/DN100,PN1.033出水阀型号/规格G41J-10/DN100,PN1.034反洗进水阀型号/规格G41J-10/DN100,PN1.035反洗排水阀型号/规格G41J-10/DN