高氯化聚乙烯底漆的用途.doc

Intended Uses用途专用于混凝土或钢结构设施表面涂装底漆，有优良的耐碱性能，对混凝土底材有很强的渗透性和封闭性，漆膜附着力强、干燥快、施工方便。Especially used for protecting surface of concrete or steel installations as primer. It forms a coatingt with excellent resistance to alkali, high penetrability and sealing. High ahdesion, quick dry and easy application. ProductInformation产品简介有铁红，浅灰等色。Iron red, light grey etc.Application details产品数据Volume Solids 固体份35%Dry Flm Thickness干膜厚度35-40 microns equivalent to 100-115 microns of wet film35-40微米相当于100-115微米湿膜厚Theoretical Coverage 理论涂布率8-10m2 /Kg 8-10平方米/公斤Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Storage and Handling施工详述Mix Radio 混合比One pack 单罐装Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Recommended 推荐采用 Conwentional Spray 传统喷涂 Recommended 推荐使用 Thinner 稀释剂 C001Cleaner 油漆设备清洗剂 C001Pot Life 使用期 Not limit 不限制Storage 贮存期 One year 一年Drying time 干燥时间SubstrateTemperature底材温度Touch Dry表干（min）Hard Dry硬干(H）Over coating Interval覆涂间隔Mix最短Max最长52535 12424 hour 小时8 hour 小时6 hour 小时 7day (天) 高氯化聚乙烯底漆的用途StorageandHandling贮存与管理Storage 贮存 Store in cool and dry conditions 贮存于阴凉干燥处 Pack size 包装规格 25Kg in 20 liter container 25公斤装于20公升容器中Flash Point 闪点 38 Specific Gravity 比重 Approx 1.25Kg/L 1.25公斤/公升Specification and Surface preparation技术要求及表面处理Steel surface: clean to Swedish Sa2.5 or rust-removed manually or with power tool to Swedish Standard St3. Concrete surface: Remove oil, grease and dust etc, prior to application钢材表面：喷射除锈至瑞典标准2.5级或手工除锈或动力工具除锈达瑞典St3级混凝土表面：除去表面油脂，灰尘等Limitations限制Subsequent coat: Highly chlorinated polyethyene anti-corrosive finish with all colors后道配套涂料：各色高氯化聚乙烯面漆 Safety Precautions 安全措施This product should be used in painting area by perfessional operators. When painting , please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.This product is a kind of solvent-based paint .Inorder to avoid danger or accident, minimal safety precautions,as follow , should be down .The paint contains volatile solvent and is flammable . So must keep away from sparks and open flames.No smoking at applacation site ,Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid producting sparks .Flash point of paint , mentioned above on product Data sheet, is the lowest temperature at which mixture of the volatile materails of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general, Therefore, 200m3 of ventilation quantuty per 1Kg solvent (according to the solvent ) is necessary.Product skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves,eye protection, face masks barrier cream and so on ). Kif paint gets in touch with skin , wass fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safety precautions(Refer to the specfications), our company will NOTbe responsible for any accident. 本产品由专业人缘在工业场所使用,使用时请参照本说明书及健康安全手册,如客户在使用本产品前,未能仔细了解有关产品的健康安全知识,请与本公司联系.该涂料为溶剂型涂料,为避免事故或危险发生,应采取最低限度的安全措施如下:此涂料为易燃物,并含有挥发性易燃溶剂,故必须远离火星和明火,严禁在作业场所吸烟,并采取有效措施,防止火星产生(如采用防爆电器设备,杜绝静电积累,避免金属撞击等)本产品说明书中所列涂料及溶剂的闪点是引起燃烧的最低温度. 施工场所应尽量进行通风良好,为消除使用过程中的爆炸隐患,应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10%,通常每千克溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10%的工作环境.采取有效措施以防止皮肤和眼睛与