电子有限公司产品样品规格书.doc

此文档收集于网络，如有侵权，请联系网站删除SPECIFICATION(产品规格书)CUSTOMER : PART NO : ZH03PW-A4-1W Project Number : ZHY110221002 DESCRIPTION: 1W WHITE HIGH POWER LED DATE : 2011-07-5 CUSTOMER APPROED(客户确认)R&D DEPARTMENT(开发部)APPROVED(核准)CHECKED(审核)PREPARED(制定) DATA SHEET ZH03系列 Features產品特點: Applications產品應用:Silica package矽膠灌封 Street lamp路燈Fast Start快速啟動 Reading lamp臺燈High-Intensity高亮度 The view illuminate景觀照明Low Attenuation低衰減 Decorative Lighting裝飾照明Long Life span壽命長 Indoor and Outdoor Lighting室內外照明No Radiation、Safety環保、安全 The signal show信號顯示Energy-Saving節能 Flashlight手電筒照明 Other uses其它用途 （一）OPTO-ELECTRONICS(產品光-電參數):(1)Absolute Maximum Rating (Ta=25)ItemSymbolAbsolute Maximum Rating (Ta=25)UnitBlue/Green/WhiteRed/YellowForward CurrentIF350350mAPeak Forward CurrentIFP500500mAPower Dissipation 350mAPD1100800mWReverse VoltageVR5VElectrostatic Discharge(HBM)ESD2000VLED Junction Temperat ureTj125Operating TemperatureTOP-40 - 80Storage TemperatureTSTG -40 - 150Thermal Resistance TypicalRjS12/WManual Soldering TimeT5 Sec. at 260(Max.)S* Absolute maximum ratings Ta=25.* IFP Conditions: Pulse Width10msec.and duty1/10(2)Initial Electrical/Optical Characteristics (Ta=25)Part No.VF(Lm)CCT/D(21/2)Min.Typ.Max.ZH03PW-A4-1W3.2-3.4V80902800-3000K140 Notes:1.Tolerance of measurement of forward voltage0.1V(電壓誤差0.1V).2.Tolerance of measurement of peakWavelength1.0nm(波長誤差為1.0nm).3.Tolerance of measurement of Luminous Flux 10%(光通量誤差為10%).4.please use together with the radiator while using LED! 務請帶上散熱板使用LED.5.In the ambient temperature of 60 degrees to use, or attenuation increase! 請儘量在60之環境溫度下使用LED，否則衰減加劇！6. Please do not squeeze hard, collision LED surface! 不要擠壓、碰撞LED表面。(二)Shape Dimensions(產品外形尺寸): Unit：mmProduct Description產品描述：Item項目Describe描述Item項目Describe描述Chip Material晶片質材ALGaInP/InGaN磷化鋁鎵銦/氮化銦鎵Colloid Color膠體顏色Transparent無色透明Emitter Color發光顏色W/R/G/B/Ypotting material灌封材料Silica矽膠Stent color支架顏色White/Black白色/黑色Lens透鏡材料Silica矽膠Bonding粘接方式Silver epoxy glue銀膠Electrode電極材質Au-plating/ Ag-plating鍍金銅材/鍍銀銅材(三)Electrical & Optical Curves-Spectrum（光&電參數曲線）： Spectral Energy Distribution（R、G、B、Y、W） IFIV Curve（R、G、B、Y、W） IFlm/w Curve（R、G、B、Y、W）Forward VoltageForward Current Curve（R、G、B、Y、W） Light intensity distributionLight Output Characteristics of Tj Room Temperature Operating Life Reliability Test Result常温点亮信赖性结果(Ta=25oC,If=700mA）Use SSC circuit board&heat sink(Tj=50oC) 使用SSC带热沉电路板(Tj=50oC)TimeHrRelative Luminous Output%使用结温在60度的使用以下，1000HR 2 degradation(1000小时衰减2%)Life Time graph (使用寿命)使用结温在60度的使用以下，50000HR 50 degradation (50000小时衰减50%) 使 用 说 明一、为避免吸潮建议将产品贮存在放有干燥剂的干燥柜中，贮存温度为：530，湿度：60%HR。二、贮存在温度较高环境的产品使用前，建议干燥，干燥条件为：1005/12个小时。三、产品在焊锡后冷却过程中避免机械压力和过大震动。四、回焊后不允许快速冷却。五、禁止焊接在变形PCB板上。六、产品不得接触水、油、有机溶液。七、产品使用最大温度值应考虑工作电流大小。八、打开防潮包装后7天内产品使用完毕。九、重新包装未使用的产品置防潮袋密封好之后贮存在干燥的地方。十、产品外观尺寸可更改而不另行通知。十一、防静电要求：使用产品时，必须戴防静电环或防静电手套，所有设备、装置、机台必须有效接地。十二、该产品必须配置恒流源驱动。(1) In order to aviod absorption of moisture it is recommended that the products are stored inthe dry box (or dessicator ) with a dessicant.Alternatively the following environment is recommended: Storage temperature :5C30C Humidity:60% HR max.(2) Storage in high humidity If the storage conditions are of high humidity the product should be dried befor use. Recommended drying conditions: 12 hours at 100C5C(3) Any mechanical force or any excess vibration should be avoied during the cooling process after soldering.(4) Reflow Rapid cooling should be avoided.(5) Components should not be mounted on distorted Printed Circuit Boards.(6) Devices should not be used in any type of fluid such as water,oil,organic solvents etc. When cleaning is required,IPA should be used.(7) The maximum ambient temperature should be taken into consideration when determining the operating current.(8) Devices should be soldered within 7 days after opening the moisture-proof packing.(9) Repack unused product in anti-moisture packing,fold to close any opening and store in a dry place.(10) The appearance and specifications of devices may be modified for improvement without notice.(11) ESD Precautions.Static Electricity and surge damages LEDs.It is recomm