eSpace U2980配置.doc

一、LMT初次连接OMU网线图注：左边单独接口为COM口，当不知道IP地址的时候可用此方法调试或查看、右边两口为RJ45普通网口OMU初始IP: 10.71.106.188掩码:255.255.255.128PC电脑IP:10.71.106.189掩码:255.255.255.128omu/mtcaPassroot/mtcaPassadmin/eSpaceU2900二、使用远程工具通过远程工具,SecureCRT或Putty工具使用22端口连接，账号:omu/mtcaPass尽量不使用root账号。(1)、进到如下目录linux-suse11: # cd /opt/HUAWEI/V100R001C10SPC400/SETOMUOMIP/注:V100R001C10SPC400不是一个绝对目录根据现场为组linux-suse11:/opt/HUAWEI/V100R001C10SPC400/SETOMUOMIP # ll/查看total 20-rwxr-xr-x 1 root root 8904 May 15 2013 SETOMUOMIP.shdrwxr-xr-x 5 root root 4096 May 15 2013 env-rwxr-r- 1 root root 3465 May 15 2013 readme.txtlinux-suse11:/opt/HUAWEI/V100R001*/SETOMUOMIP # ./SETOMUOMIP.sh 执行脚本修改IP以下为自动初始化过程，无需操作Get the users passwd is successful . - Tool for setting omu virtual IP in huawei CDE Release 1.0 Copyright 2004-2014 Huawei Technologies Co., Ltd. All rights reserved. NOW START TO MODIFY OMU VIRTUAL IP.-The omu server will be stop in 6 seconds ! Press Ctrl + C to break.Stopping OMU Checker done Stopping OMU Monitor done Stopping Mirror done Stopping OMU Services done Mirror and OMU are stopped successfully.自动初始化过程，成功。= Setting the virtual IP address:以下设置IP地址、网关、掩码.红色标记为准。NOTICE1. The virtual IP address is an external IP address and is used when a client is connected to the CDE.2. The virtual IP address cannot be the same as any existing IP address except the local IP address.3. The virtual IP address must be in the same network segment as the external IP address of the CDE.Please input virtual IP addressQuit: 93.12.83.90= Setting the network mask for virtual IP address:NOTICEYou can press Enter to keep the network mask as 255.255.0.0Please input the network maskQuit:255.255.255.0= Setting the gateway for virtual IP address:NOTICEYou can press Enter to skip this step.Please input the gatewayQuit:93.12.83.254NOTICEThe new omu virtual IP information is as below:- 1.IP address used for client connecting: IP addr:93.12.83.90 Mask:255.255.255.0 Gateway:93.12.83.254 -Are you sure all the above information is correct?1. If you input y, the omu virtual IP will be modified.2. If you input n, you can reconfigure the above infomations.3. If you input q, the current setting will exit.Please input your choiceYes,No,Quit:y/按y后自动重启，需要二十分钟。gs_ctl: server is running (PID: 5742)/opt/gaussdb/program/bin/gaussdbgs_ctl: server is running (PID: 5742)/opt/gaussdb/program/bin/gaussdbthe Num of Record is 1.the server is running. Updating mirror configuration .DONEUpdating configuration .DONE安装CDE工具，参考文档全部下一步完成。三、配置系统数据1、点击对像导航树。 /2、右击选中UAP网元，启动MML。3、修改网元信息MOD ME: SNID=0, MEID=5, MELN=随意编写;四、配置硬件数据1、硬件机架网元数据ADD RACK: RN=1, RNM=gs12328, POSNUM=1, ROWNUM=1, COLNUM=1;2、硬件机框网元数据ADD SUBRACK: SRN=1, RN=1, PN=1, SRNNM=gs12366jk;3、增加第1框配置1、添加OMU板ADD BRD: SRN=1, SN=1, METYPE=COMMON, FBRDHTYP=OMU, APPTYPE=OMUDLAR;2、添加MSU板ADD BRD: SRN=1, SN=2, METYPE=UAP, FBRDHTYP=AMSU0, APPTYPE=AUAPP;ADD BRD: SRN=1, SN=5, METYPE=UAP, FBRDHTYP=AMSU0, APPTYPE=AUAPP;3、添加GPU板ADD BRD: SRN=1, SN=3, METYPE=UAP, FBRDHTYP=AGPU, APPTYPE=AUAPP;ADD BRD: SRN=1, SN=4, METYPE=UAP, FBRDHTYP=AGPU, APPTYPE=AUAPP;4、添加CIU板ADD BRD: SRN=1, SN=9, METYPE=UAP, FBRDHTYP=ACIU, APPTYPE=AUAPP;5、添加SMU板注意默认不需要添加此项，出厂的时候预配的，最后配置完成重启单板。6、关闭没有用到的网口MOD PORT: SRN=1, SN=2, PORTID=1, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=2, PORTID=2, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=3, PORTID=1, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=3, PORTID=2, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=4, PORTID=1, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=4, PORTID=2, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=5, PORTID=1, PORTMOD=OFF,OAMST=IGN;MOD PORT: SRN=1, SN=5, PORTID=2, PORTMOD=OFF,OAMST=IGN;7、设置E1端口SET E1PORT: MN=600, WM=E1_UNBALANCE, FF=DOUBLE_FRAME, TC=HDB3, RC=HDB3, EN=CONFIG;五、配置时钟源1、配置时钟数据ADD CLKSRC: CLKSRCTYPE=BITS1, PRIORITY=FIRST, SIGNALTYPE=HZ2M, CLKINSBRN=1, CLKINBRDTYPE=SMU;六、配置本局基础数据1、增加GPU进程组ADD PG: SRN1=1, SN1=3, PGT=PG6, ASSFLAG1=YES, SRN2=1, SN2=4, CCU1MN=56, CDB1MN=184, CDB1FT=CDB+RDB, CDBVMRPID1=0, BSG1MN=216, ASBSGMN=217, IFM1MN=8, CMU1MN=344, CMUVMRPID1=0;2、增加MSU进程组ADD PG: SRN1=1, SN1=2, PGT=PG8, MSU1MN=472;ADD PG: SRN1=1, SN1=5, PGT=PG8, MSU1MN=473;3、增加CIU进程组ADD PG: SRN1=1, SN1=9, PGT=PG9, CIUMN=600;4、IFM IP、网关规划/IFM进程IP用于座席注册ADD FECFG: MN=8, LOC=USP, IP=10.47.33.8, MSK=255.255.255.240, PEERCHK=FALSE;ADD GWIP: SRN=1, SN=3, LOC=USP, IFMMN=8, IP=10.47.33.30;5、设置一线接入SET SMUFECFG: NPT=TRK;6、CTI LNK IP规划ADD MEMLNK: MN=8, SDN=0, LNKNO=0, LNKNAME=TO_CTI, PT=FEP, LIP=93.12.83.95, RIP1=93.12.64.80, RIP2=93.12.64.87, RP=5600;7、添加CDB功能ADD CDBFUNC: CDPM=184, FCF=LOC-1&TK-1&MGWR-1&DISP-1&SPDNC-1>TSLICM-1&LINCENCON-1;七、配置本局和计费数据1、配置OFISET OFI: APPTYPE=GENERAL, COMTYPE=MGC, ST=CC, OFN=gs12328, LOT=CMPX, IN=NO, IRN=NO, NN=YES, NRN=NO, SN1=NAT, SN2=NAT, SN3=NAT, SN4=NAT, NNC1=D22222, NNS=SP24, SPF=YES, STP=NO;2、增加本地号首集ADD LDNSET: LP=0, NC=K86, AC=K0931, LDN=gs12328;3、增加呼叫源码ADD CALLSRC: CSC=0;4、增加计费情况索引ADD CHGIDX:;八、配置MGC对接MRP数据1、设置虚拟媒体资源节点SET VMRP: VMRPID=0;2、添加媒体网关控制器ADD MGC: VMRPID=0, MIDTYPE=IP, MGCIDX=0, MID=192.168.0.1:9090, PRONEGO=NO;3、添加媒体网关ADD MRP: MRPNAME=MRP, MRPTYPE=MRP, TRNST=Q922, MMN=184, VMRPID=0;4、添加TDM端点/ADD TDMIU: CIUMN=600, CMUMN=344, BRDTYPE=CIU, VMRPID=0, STID=0, ETID=383, TTYPE=NOR2;5、激活虚拟媒体资源节点ACT VMRP:VMRPID=0;/等单板状态正常，才能激活6、激活媒体资源节点ACT MRP: MRPNAME=MRP;/等单板状态正常，才能激活九、配置PRA中继1、配置PRA信令数据(1)SIP全局配置SET SIPCFG: UST=NO;(2)设置协议分发能力SET DPA: MN=216, DA=SIP-1;SET DPA: MN=217, DA=SIP-1;(3)添加PRA链路ADD PRALNK: PLN=0, MN=56, BEARTYPE=Q921, SC=16, CIUMN=600, E1T1N=0, SIGT=USER;2、配置路由数据(1)增加局向ADD OFC: O=0, ON=GSGX, DOT=CMPX, DOL=SAME, OFCTYPE=COM, SIG=NONBICC/NONSIP, IFCFLAG=NO;(2)增加子路由ADD SRT: SRC=0, O=0;(3)增加路由ADD RT: R=0, SRST=SEQ, UCART=NO, SR1=0;ADD RT: R=1, SRST=SEQ, UCART=NO, SR1=1;(4)增加路由分析ADD RTANA: RSC=0, RSSC=0, TM=TMX, TMX=0, R=0;3、配置PRA中继数据(1)增加PRA中继群ADD PRATG: TG=0, MRPNAME=MRP, SRC=0, PLN=0;(2)增加PRA中继电路ADD PRATKC: MN=56, TG=0, SC=0, EC=31, TID=0;十、配置资源数据1、增加站点配置ADD RCWSCFG: WSNO=0, MMN=184, WSTYPE2=MSUA, MODULENO=472, RESCAP=IVR-1&CONF-1&FAX-1&TTS-1;ADD RCWSCFG: WSNO=1, MMN=184, WSTYPE2=MSUA, MODULENO=473, RESCAP=IVR-1&CONF-1&FAX-1&TTS-1;2、外置文件服务器ADD FSCFG: FSI=0, FSDESC=fileserver, FSTYPE=OUTSIDE, IP1=93.12.64.81; /增加文件服务器3、增加文件盘符ADD VOLCFG: VOL=y:, VOLIND=0, FSDIR=/fileserver, FSIND1=0;4、配置MSU本地IP/MSU本地IP用于fileserver服务器通信使用。SET MSULOCALIP: MN=472, IP=93.12.83.91, MASK=255.255.255.0, GW=93.12.83.254;SET MSULOCALIP: MN=473, IP=93.12.83.93, MASK=255.255.255.0, GW=93.12.83.254;4、TTS配置信息设置TTS管理参数SET TTSMANAGER: MRPID=0, TTSLICM=LARGEMODE;参数调整MOD SFP: ID=P904, MODTYPE=P0, VALUE=46ff;TTS服务器连接模式SET TTSCON: MNSRMIP=10.47.33.23;修改模块参数MOD MPRM: ID=P80, VAL=0;MOD SFP ID:P91,MODTYPE=P1,BIT=2,BITVAL=0;增加TTS盘符5、ASR配置/ADD MRCPSRV实际应用中没用配置，待了解。SET ASRLICSET ASRLIC6、MSU承载数据IP规划/MSU承载IP用于处理SIP/RTP协议是关信息SET MSUBEARIP: MN=472, IP=93.12.83.92, MASK=255.255.255.0, GW=93.12.83.254, DEVID=USP;SET MSUBEARIP: MN=473, IP=93.12.83.94, MASK=