NXP SSL21083高压8W LED驱动解决方案.doc

NXP SSL21083高压8W LED驱动解决方案关键词：电源管理,LED驱动器,AC/DC转换器NXP公司的SSL2108x系列是高压LED驱动器,集成了300V(SSL21081和 SSL21082)或多或少(SSL21083和SSL21084),开关接通采用零电流开关(ZCS),开关关断采用零电压或谷底电压开关,输出信号采用PWM调制,主要用在输入电压100V/120VAC和230VAC的紧凑型LED照明.本文介绍了SSL2108X主要特性和优势,框图, 基本应用框图,SSL21083参考板主要指标,电路图和材料清单.The SSL2108X is a range of high-voltage Integrated Circuits (ICs), intended to drive LED lamps in general lighting applications.The main benefits of the product family are:Small Printed-Circuit Board (PCB) footprint, and compact solutionHigh efficiency (up to 95 %)Ease of integrationLow electronic Bill Of Material (BOM)The product family is made of ICs with a range of internal HV switches for easy power scaling.The ICs work as boundary conduction mode converters, typically in buck configuration.The IC range has been designed to start up directly from the HV supply by an internal high-voltage current source. Thereafter, the dV/dt supply is used with capacitive coupling from the drain, or any other auxiliary supply. This functionality provides full flexibility in the application design. The IC consumes 1.3 mA of supply current with an internal clamp limiting the supply voltage.The ICs provide accurate output current control with LED current accuracy within 5%. The ICs can be operated using Pulse-Width Modulation (PWM) dimming and has many protection features including easy LED temperature feedback.SSL2108X主要特性和优势:nLED driver IC family driving strings of LEDs from a rectified mains supplynHigh-efficiency switch mode buck driver product family:uDrivers with integrated 300 V (SSL21081 and SSL21082) or 600 V (SSL21083 and SSL21084) power switchesnController with power-efficient boundary conduction mode of operation with:uNo reverse recovery losses in freewheel diodeuZero Current Switching (ZCS) for turn-on of switchuZero voltage or valley switching for turn-on of switchuMinimal required inductance value and sizenDirect PWM dimming possiblenFast transient response through cycle-by-cycle current control:uNegligible AC mains ripple at LED current and minimal total capacitor valueuNo over or undershoots in the LED currentnNo binning on LED forward voltage requirednInternal Protections:uUnderVoltage LockOut (UVLO)uLeading-Edge Blanking (LEB)uOverCurrent Protection (OCP)uShort-Winding Protection (SWP)uInternal OverTemperature Protection (OTP)uBrownout protectionuOutput Short Protection (OSP)nLow component count (see Figure 4) LED driver solution:uNo Schottky diode required due to ZCSuNo dim switch and high-side driver required for PWM dimminguEasy external temperature protection with a single NTC resistoruOption for soft-start functionuCompatible with wall switches with built-in indication light during standby1nIC lifetime easily matches or surpasses LED lamp lifetimeSSL2108X应用:SSL2108X products are intended for compact LED lighting applications with accurate fixed current output for single mains input voltages. Mains input voltages include 100 V, 120 V and 230 V (AC). The output signal can be modulated using a PWM signal.图1.SSL2108X方框图图3.SSL21081/SSL21083降压应用配置SSL21083参考板The board is optimized for a 230 V (AC, 50 Hz) mains supply. In addition to the mains voltage optimization, the board is designed to work with multiple LEDs or an LED module with a high forward voltage.Mains connection of this reference board is different from other general evaluation/demo boards. Connect the mains to the screw connector J6.Remark: The maximum rated voltage of the board is 280 V (limited by the value of electrolytic capacitor C1) or 400 V (DC).The anode of the LED load is connected to positive positions 1 to 3 of connector J5. The cathode is connected to negative 4 to 6 of connector J5.Use an LED string with a VF greater than 20 volt on this board.