4000 V3.0日常维护(原).doc

1. 进入维护系统ComWin维护终端IP：192.0.2.30，子网掩码：255.255.255.0系统IP：192.0.2.3（通过comwin访问）192.0.2.5（通过IE，assistant访问，ID：engr，PW：Hipath4000）按 Ctrl-T 登陆系统 大石OCC，HiPath4000 v5.0ID:engineer；PW:sbcs-engr 8APMOCC，HiPath4000 v5.0ID:engineer；PW:install或ID:user；PW:hipath（管理员）厦滘车辆段，HiPath4500 v1.0ID:engineer；PW:install按 Ins 插入修改； 按 Ctrl-C 取消指令按 显示上一条指令/查找上翻一行，按 显示下一条指令/查找下翻一行2. AMO 指令语法结构：动词 - 指令：参数,参数,参数;常用动词：ADD 建立新数据 例：ADD-SCSUCHA 修改当前数据 例：CHA-COSSUDIS 查看当前数据 例：DIS-ACSUDEL 删除当前数据 例：DEL-WABEREG 再生当前数据 例：REG-ACSUEXE 执行处理 例：EXE-UPDATSTA 启动处理 例：STA-REGENDEA 关闭 例：DEA-DSSUACT 开启 例：ACT-DSSU常用指令：WABE 设置系统号码使用方案COSSU 定义服务等级SCSU 设置分机SBCSU 设置ISDN 数字话机TAPRO 数字话机功能键标准使用方案ACSU 设置话务台NAVAR 定义话务台夜服转换终端VFGR 定义话务台应答组VFGKZ 定义话务台应答组内线BUEND 定义中继组TACSU设置模拟中继线TDCSU设置数字中继线RICHT 设置出中继路由LODR 设置LCR 发号规则LDAT 设置LCR 路由数据LDPLN 设置LCR 出局号码PERSI 定义私人密码或个人识别号码ZIEL 为分机定义目的地号码SA 设置寻线组AUN 设置代答组HOTLN 定义热线电话应答设备ACTDA 启动用户功能3. 查看系统状况 ORDER：DIS-BCSU：TBL； DIS-BCSU:TBL;DIS-BCSU:TBL;H500: AMO BCSU STARTED ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1 -+-+-+-+-+-+-+-+-+-+ | ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE | PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS | -+-+-+-+-+-+-+-+-+-+ 19 | AVAILABLE | | AVAILABLE | | | | 25 | Q2196-X DIU-N2 1 A | | Q2196-X | 1 | -04 - | READY | 31 | AVAILABLE | | AVAILABLE | | | | 37 | AVAILABLE | | AVAILABLE | | | | 43 | AVAILABLE | | AVAILABLE | | | | 49 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 55 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 61 | Q2468-X RG-USA | | Q2468-X | 1 | - | READY | 67 | AVAILABLE | | AVAILABLE | | | | 73 | Q2166-X LTUCX | | Q2166-X | 1 | -05 - | READY | 79 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 85 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 91 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 97 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 103 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 109 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 115 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY | 121 | Q2246-X SLMA24 A | | Q2246-X | 1 | -07 - | READY |注： 1: DIU-N2表示2M*2中继板卡,即60路外线板卡2: SLMA24:24路普通分机板卡3: SLMO24:24路数字分机板卡4: SIUX2:信令板卡5: LTUCX:主控板卡(副柜和主机柜直接的连接板卡)6: RG-USA :铃流板卡4. 系统状态查看：显示: READY 正常； BUSY/CP 占用； DEF 故障查看1-1-25-15端口的状态DIS-SDSU:ALL,PEN,PER3,1,1,25,15; 8查看1-1-25槽口板块的状态DIS-SDSU:ALL,PEN,PER3,1,1,25; 8查看1-1框的状态DIS-SDSU:ALL,PEN,PER3,1,1; 8查看系统的状态DIS-SDSU:ALL,PEN,PER3; 8查看1000分机的状态DIS-SDSU:ALL,STNO,PER3,1000; 85. 查看分机属性：DIS-SDAT： STNO=输入分机号码； DIS-SDAT:8100TYPE = ;DIS-SDAT:8100,;H500: AMO SDAT STARTED - SUBSCRIBERDATA - STNO = 8100 COS1 = 10 DPLN = 0 SSTNO = NO PEN : 1- 1- 31- 16 COS2 = 10 ITR = 0 TRACE = NO DVCFIG : ANATE LCOSV1 = 1 COSX = 0 ALARMNO = 0 AMO : SCSU LCOSV2 = 1 SPDI = 0 RCBKB = NO LCOSD1 = 1 SPDC1 = RCBKNA = NO KEYSYS : LCOSD2 = 1 SPDC2 = - CDRACC = SRCGRP = ( 1) TCLASS = CLASSMRK = EC G711 G729OPT PUBNUM = 25328888 TON = SUBSCR NPI = ISDN NNO = 100 HOTIDX = STNOOOS = MVHFAIP = NO STNOAPE = AMOALTRT = NO GWIPADR : CLUSTID = SVCDOM = PRECLEV = BWLIDX = - ATTRIBUTES - AMO-SDAT -111 ADMINISTRATION OF SUBSCRIBER ATTRIBUTES AND DATA DISPLAY COMPLETED;注： 1: 位置Pen:1(第一个栈)-1(第一个机柜)-49(槽位为49)-7(端口从0-23)2: 等级LCOSV:1:内线,2:市话,3:国内长途,4:国际长途6. 加分机加上梅林的分机8100上梅林要做的数据ADD-WABE:8100,STN,N,; ( DEL-WABE:CD,8001,STN; )ADD-SCSU:8100,1-2-55-7,ANATE,0,0,10,10,1,1,1,1,0,0,0,VAR,YES,NO,0,DIR,YES,NO,0; ( DEL-SCSU:8001,ALL; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFB,INT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFB,EXT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFNR,EXT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ACTDA:STN,8100,FWD,SYSTEM,VCE,; ( DEL-ACTDA:STN,8100; )CHANGE-SDAT:8100,DATA1,100,25328888,SUBSCR,ISDN;下梅林要做的数据ADD-WABE:8100,TIE,N,; ( DEL-WABE:CD,8100,TIE; )ADD-LDPLN:LCRPATT,0,8100,550,1,N; ( DEL-LDPLN:LCRPATT,0,8100; )加下梅林的分机8100下梅林要做的数据ADD-WABE:8100,STN,N,; ( DEL-WABE:CD,8001,STN; )ADD-SCSU:8100,1-2-55-7,ANATE,0,0,10,10,1,1,1,1,0,0,0,VAR,YES,NO,0,DIR,YES,NO,0; ( DEL-SCSU:8001,ALL; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFB,INT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFB,EXT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ZIEL:FWD,8100,VCE,8888,VOICE MAIL ,CFNR,EXT,SYSTEM; ( DEL- ZIEL:FWD,8100; )ADD-ACTDA:STN,8100,FWD,SYSTEM,VCE,; ( DEL-ACTDA:STN,8100; )CHANGE-SDAT:8100,DATA1,100,25328888,SUBSCR,ISDN;上梅林要做的数据ADD-WABE:8100,TIE,N,; ( DEL-WABE:CD,8100,TIE; )ADD-LDPLN:LCRPATT,0,8100,550,1,N; ( DEL-LDPLN:LCRPATT,0,8100; )7. DID分机设置做DID号码25328001对应上梅林分机8306;上梅林要做的数据 ADD-WABE:28001,STN,N,; ( DEL-WABE:CD,28001,STN; )ADD-RUFUM:DID,28001,8306; ( DEL-RUFUM:28001; )CHANGE-SDAT:8306,DATA1,100,25328001,SUBSCR,ISDN;下梅林要做的数据 ADD-WABE:28001,TIE,N,; ( DEL-WABE:CD,28001,TIE; )ADD-LDPLN:LCRPATT,0,28001,550,1,N; ( DEL-LDPLN:LCRPATT,0,28001; )做DID号码25328001对应下梅林分机8306;下梅林要做的数据 ADD-WABE:28001,STN,N,; ( DEL-WABE:CD,28001,STN; )ADD-RUFUM:DID,28001,8306; ( DEL-RUFUM:28001; )CHANGE-SDAT:8306,DATA1,100,25328001,SUBSCR,ISDN;上梅林要做的数据 ADD-WABE:28001,TIE,N,; ( DEL-WABE:CD,28001,TIE; )ADD-LDPLN:LCRPATT,0,28001,550,1,N; ( DEL-LDPLN:LCRPATT,0,28001; )8. 做寻线组增加寻线组0ADD-WABE:0,HUNT,N,;ADD-SA:VCE,0,0,8711&8712&8713,LIN,0,OPERATOR ,Y,DESTEXT,8000;增加寻线组0里分机8714&8715ADD-SA:STN,0,VCE,8714&8715;删除寻线组0DEL-SA:CD,0;删除寻线组0的走向的分机8712DEL-SA:STN,0,VCE,8712;9. 做分机走向做分机8711走向8711到8712到8713ADD-SA:VCE,8711,0,8711&8712&8713,LIN,0,OPERATOR ,Y,DESTEXT,8000;增加分机8711走向里分机8714&8715ADD-SA:STN,8711,VCE,8714&8715;删除分机8711的走向DEL-SA:CD,8711;删除分机8711的走向的分机8712DEL-SA:STN,8711,VCE,8712;10. 做代接组查看代接组REG-AUN; REG-AUN;REG-AUN;H500: AMO AUN STARTEDADD-AUN:1,8327,YES,ON3,NO,ALL,;ADD-AUN:5,8150&8151&8177&8199&8778,YES,ON3,NO,ALL,;ADD-AUN:11,8272&8274,YES,ON3,NO,ALL,;ADD-AUN:12,8216&8398,YES,ON3,NO,ALL,;ADD-AUN:13,8219&8394,YES,ON3,NO,ALL,; AMO-AUN -111 CALL PICKUP GROUPS REGENERATE COMPLETED;增加代接组在上梅林2.0版本上ADD-AUN:,8321&8326&8327&8365,YES,ON3,NO,ALL,;在下梅林3.0版本上ADD-AUN:,GR,8321&8326&8327&8365,YES,ON3,NO,ALL,;删除代接组DEL-AUN:GR,4;删除组成员：DEL-AUN:TYPE=STN,GRNO= （组号）,STNO=3198（分机号）;11. 删除分机号码(必须分机先退出代接组，寻线组和DID设置RUFUM)DEL-SCSU:8100,ALL; 删除普通分机DEL-SBCSU:8100,ALL; 删除数字分机12. 修改分机密码修改帐号分机58000密码为1234ADD-PERSI:STN,58000,1234,YES,;13. 修改普通分机号码分机1000修改为2000查看号码分配情况REG-WABE; 增加分机号码2000ADD -WABE:2000,STN,N; 8 （其中STN代表号码分配为分机号）显示普通分机REG-SCSU; 8分机1000修改为2000 CHA-SCSU 8 STNO = 1000 8 8 NEWNO = 2000; 8或 CHA-SCSU:STNO=1000,NEWNO=2000; 814. 修改数字分机号码分机1000修改为2000查看号码分配情况 REG-WABE; 8增加分机号码2000 ADD-WABE:2000,STN,N; 8 （其中STN代表号码分配为分机号）显示数字分机 REG-SBCSU; 8分机1000修改为2000 CHA-SBCSU 8 STNO = 1000 8 8 NEWNO = 2000; 8或 CHA-SBCSU:STNO=1000,NEWNO=2000; 815. 修改分机号码CHA-SDAT: STNO=输入分机号码 TYPE=DATA NEWNO=新的分机号码；Ex:分机8008修改为8608 CHA-SDAT:STNO = 8008TYPE = DATANEWNO = 8608COS1 = ;CHA-SDAT:8008,DATA,8608,;H500: AMO SDAT STARTEDH08: THE STNO 8008 HAS THE NEW NUMBER 8608.H02: 8608 SCSU-STATION DATA CHANGED.AMO-SDAT -111 ADMINISTRATION OF SUBSCRIBER ATTRIBUTES AND DATA CHANGE COMPLETED;16. 修改服务等级LCOSV查看服务等级LCOSV REG-COSSU:LCOSV; 8显示: CHA-COSSU:LCOSV,1,2&32,; (内线等级) CHA-COSSU:LCOSV,2,1&2,; (只允许拨打 拨号方案等级1、2) CHA-COSSU:LCOSV,3,1&3,; (只允许拨打 拨号方案等级1、2、3) CHA-COSSU:LCOSV,4,1&4,; (只允许拨打 拨号方案等级1、2、3、4) CHA-COSSU:LCOSV,32,1&32,; (全开放等级)查看拨号方案,框内赋值为拨号方案等级 REG-LDPLN; 8显示:ADD-LDPLN:LCRPATT,0,9-00X,100,4,N; ADD-LDPLN:LCRPATT,0,9-0X,100,3,N; ADD-LDPLN:LCRPATT,0,9-X,100,2,N; 删除9-0X拨号方案 DEL-LDPLN:LCRPATT,0,9-00X; 8增加拨号方案限制拨打0市话168，拨号方案等级为5 ADD-LDPLN:LCRPATT,0,9-168X,100,5,N; 8新建一个服务等级5 CHA-COSSU:LCOSV,5,1&5; 817. 修改普通分机服务等级LCOSV查看分机服务等级LCOSV DIS-SCSU:1000; 8修改分机1000的服务等级LCOSV为2等级 CHA-SCSU:1000,2,2; 8或 CHA-SCSU 8 STNO = 1000 8 8 LCOSV1 = 2 8 LCOSV2 = 2; 8（密码锁后的等级）18. 修改数字分机服务等级LCOSV查看分机服务等级LCOSV DIS-SBCSU:3000; 8修改分机3000的服务等级LCOSV为2等级 CHA-SBCSU 8 STNO = 3000 8 8 LCOSV1 = 2 8 LCOSV2 = 2; 8（密码锁后的等级）或 CHA-SBCSU:3000,2,2; 819. 修改分机服务等级LCOSV先查看分机等级DIS-SDAT:分机号；号码（见上面）修改分机等级 CHA-SDAT: 8STNO = 1000TYPE=DATA 8 8LCOSV1 = 2 8(1:内线,2:市话,3:国内长途,4:国际长途)LCOSV2 = 2; 8（COS等级转换后的等级,与LCOSV1类似）：将分机动等级开放为市话 CHA-SDAT:STNO = 6678TYPE = dataNEWNO = COS1 = COS2 = LCOSV1 = 2(等级)LCOSV2 = 2 (等级)LCOSD1 = ;CHA-SDAT:6678,DATA,2,2,;H500: AMO SDAT STARTEDH02: 6678 SBCSU-STATION DATA CHANGED.AMO-SDAT -111 ADMINISTRATION OF SUBSCRIBER ATTRIBUTES AND DATA CHANGE COMPLETED;20. 分机添加、修改姓名给分机1000 添加姓名