多孔介质设置及建模实例.doc

我做的多孔介质的简单例子（均为k-eRNG所做）)模型仿真结果 多孔介质定义的方法(2008-12-14 20:28:12)不知道怎的，这些日子都跟多孔介质干上了1. Define the porous zone.2. Define the porous velocity formulation. (optional)3. Identify the fluid material flowing through the porous medium.4. Enable reactions for the porous zone, if appropriate, and select the reaction mechanism.5. Set the viscous resistance coefficients and the inertial resistance coefficients , and define the direction vectors for which they apply. Alternatively, specify the coefficients for the power-law model.6. Specify the porosity of the porous medium.7. Select the material contained in the porous medium (required only for models that include heat transfer). Note that the specific heat capacity, , for the selected material in the porous zone can only be entered as a constant value.8. Set the volumetric heat generation rate in the solid portion of the porous medium (or any other sources, such as mass or momentum). (optional)9. Set any fixed values for solution variables in the fluid region (optional).10.Suppress the turbulent viscosity in the porous region, if appropriate.11. Specify the rotation axis and/or zone motion, if relevant.fluent中多孔介质porousmedia设置问题(2008-12-13 20:08:07)标签：杂谈 分类：CFD计算流体力学经过痛苦的一段经历，终于将局部问题真相大白，为了使保位同仁不再经过我之痛苦，现在将本人多孔介质经验公布如下，希望各位能加精：1。Gambit中划分网格之后，定义需要做为多孔介质的区域为fluid,与缺省的fluid分别开来，再定义其名称，我习惯将名称定义为porous;2。在fluent中定义边界条件define-boundary condition-porous(刚定义的名称)，将其设置边界条件为fluid,点击set按钮即弹出与fluid边界条件一样的对话框，选中porous zone与laminar复选框,再点击porous zone标签即出现一个带有滚动条的界面；3。porous zone设置方法：1）定义矢量：二维定义一个矢量，第二个矢量方向不用定义，是与第一个矢量方向正交的；三维定义二个矢量，第三个矢量方向不用定义，是与第一、二个矢量方向正交的；（如何知道矢量的方向：打开grid图，看看X,Y,Z的方向，如果是X向，矢量为1,0,0,同理Y向为0,1,0，Z向为0,0,1,如果所需要的方向与坐标轴正向相反，则定义矢量为负）圆锥坐标与球坐标请参考fluent帮助。2）定义粘性阻力1/a与内部阻力C2：请参看本人上一篇博文“终于搞清fluent中多孔粘性阻力与内部阻力的计算方法”，此处不赘述；3）如果了定义粘性阻力1/a与内部阻力C2,就不用定义C1与C0，因为这是两种不同的定义方法，C1与C0只在幂率模型中出现，该处保持默认就行了；4）定义孔隙率porousity，默认值1表示全开放，此值按实验测值填写即可。完了，其他设置与普通k-e或RSM相同。总结一下，与君共享!终于搞清fluent中多孔粘性阻力与内部阻力的计算方法Experimental data that is available in the form of pressure drop against velocity throughthe porous component, can be extrapolated to determine the coecients for the porousmedia. To e ect a pressure drop across a porous medium of thickness, n, the coecientsof the porous media are determined in the manner