IP通信实验报告——RIP.doc

IP通信基础实验报告 RIP实验一、 实验目的1.掌握在GAR路由器上配置RIP所需的基本命令；2.掌握RIP的基本原理二、 实验内容（仿真程序路由器RIP.pkt） GAR路由器的RIP协议配置三、 实验设备路由器 3台PC机 2台交叉网线 4条四、 实验拓扑图五、 配置步骤RT1=配置底层- System Configuration Dialog -Continue with configuration dialog? yes/no: noPress RETURN to get started!RouterenableRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ho RT1RT1(config)#interface fRT1(config)#interface fastEthernet 0/0RT1(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to upRT1(config-if)#ip address 192.168.10.254 255.255.255.0RT1(config-if)#exitRT1(config)#interface fastEthernet 1/0RT1(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to upRT1(config-if)#ip adRT1(config-if)#ip address 12.12.12.1 255.255.255.0RT1(config-if)#exitRT1(config)#RT2=配置底层=Continue with configuration dialog? yes/no: noPress RETURN to get started!RouterenableRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ho RT2RT2(config)#interface fastEthernet 1/0RT2(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to upRT2(config-if)#ip address 12.12.12.2 255.255.255.0RT2(config-if)#exitRT2(config)#interface fastEthernet 1/1RT2(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to upRT2(config-if)#ip RT2(config-if)#ip aRT2(config-if)#ip addRT2(config-if)#ip address 23.23.23.2 255.255.255.0RT2(config-if)#exitRT2(config)#RT3=配置底层=Continue with configuration dialog? yes/no: noPress RETURN to get started!RouterenableRouter#configure terminal Enter configuration commands, one per line. End with CNTL/Z.Router(config)#ho RT3RT3(config)#interface fastEthernet 1/1RT3(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet1/1, changed state to upRT3(config-if)#ip address 23.23.23.1 255.255.255.0RT3(config-if)#exitRT3(config)#interface fastEthernet 0/0RT3(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to upRT3(config-if)#ip address 192.168.20.254 255.255.255.0RT3(config-if)#endRT1=配置RIP=RT1(config)#router ripRT1(config-router)#version 2RT1(config-router)#no auto-summary RT1(config-router)#network 192.168.10.0 此处是与中兴RT命令不同之处RT1(config-router)#network 12.12.12.0RT1(config-router)#end%SYS-5-CONFIG_I: Configured from console by consoleRT1#RT2=配置RIP=RT2(config)#route ripRT2(config-router)#versRT2(config-router)#version 2RT2(config-router)#no auto-summary RT2(config-router)#network 12.12.12.0RT2(config-router)#network 23.23.23.0RT2(config-router)#end%SYS-5-CONFIG_I: Configured from console by consoleRT1#RT3=配置RIP=RT3(config)#route ripRT3(config-router)#version 2 /版本2RT3(config-router)#no autRT3(config-router)#no auto-summary 关闭自动汇聚RT3(config-router)#network 23.23.23.0RT3(config-router)#network 192.168.20.1RT3(config-router)#end%SYS-5-CONFIG_I: Configured from console by console=RT3#show ip routeRT2#debug ip rip