GIS-10_Infotainment_Power_moding_Specification.doc

Global Infotainment Standard Revision X.XGIS- Date: XXXX, 2005GIS 10A Global A Infotainment Power Mode InterfaceDocument Owner InfoThis specification is owned by:Steve SnyderGM Global Electrical Center586-575-3108Stephen.SRevision LogRevision #ROINChangeAuthorDate1.0AllInitial Release for Global ICS Rev 2.0 SORS. Rush19NOV20041.1AllRewrote Section to accommodate global AS. Snyder03MARCH20051.2GIS 10-002Deleted use cases from diagramS. Snyder09MARCH20051.2GIS 10-003Elaboration“1.2GIS 10-032New section defining ignition startup cal“1.2GIS 10-024Added what media to test with“1.2GIS 10-026Elaboration“1.2GIS 10-027Made clock recall in off a calibration“1.2AllChange references to EHU to silverbox or SB“1.2GIS 10-023Added incoming call as beginning of timer countdown“1.2ALLRenamed doc. For just global A and also changed gis-10 to gis-10GA“11MARCH20051.3GIS 10A-010Changed powermoding reference document to match that for global A“23MAY20051.3GIS 10A-033New Requirement for Silverbox to implement logistic mode“23MAY20051.4GIS 10A-027Added additional wakeups to power up the radio“10JUNE20051.4GIS 10A-023- Changed requirement #5 to refer to local wakeup which describes all buttons that can power up the radio. - Added mute line as a reason to reset the timer“21June20051.4GIS 10A-034New GIS. Designates the mute line as a wakeup“21June20051.4GIS 10A-027Cleaned up requirement #3. Created a calibration for wakeups.“21June20051.5GIS 10A-023Added to #3 and #4 a first detection rule“09August2005DRAFT 1.6 IN Progress1.6GIS 10A-010Changed LS CAN to GMLANS. Snyder1Dec20051.6GIS 10A-017Changed VIP to SBS. Snyder1Dec20051.6GIS 10A-018Removed Protection fuse note not needed1.6GIS 10A-019Remove reference to IVLANS. Snyder1Dec20051.6GIS 10A-020Removed reference 10 (does not exsist)1.6GIS 10A-32Changed inaccurate statement “to hmi inactive to last known stateS. Snyder1Dec20051.6GIS 10A-27Changed verbage in number 4. to specific wakeups1.6GIS 10A-010Added remote start statusS. Snyder1Dec20051.6GIS 10A-015Changed gps not avail 16 V to 26.5 V. the under voltage range is 0 V to 9 V. FunctionsStatusRadio =Not Available 9 V GPS* =Not Available 9.0 VCAN transceiver =Not Available 6 VNavigation* Not Available 9.0 V-Turn by turn-MAP (video interface available)-Dynamic Navigation -Intersection zoom/stylized iconsAudio (DSP functionality)Not Available 9VInt. drives (CD-MP3)Not Available 9V Int. drives (CD-ROM, DVD)*Not Available 9V Update Possibility via Drive*Not Available 9.0VBack light / illuminationNot Available 9.0VSupport of PersonalizationNot Available 6.0V *items particular to navigation units only.GIS-10A-016 Functionality While in Over Voltage (16 V to 18 V)Under the exposure of supply voltage from 16 V to 18 V the SB shall transit to SB protection mode. From protection mode there shall be a possibility to turn off the unit.When the supply voltage rises above 16 V the audio shall be muted and the illumination shall be switched off. In case the CD is active then the CD shall be stopped. The display shall remain frozen. All CD related user commands are ignored. All other SB functionality remains unaffected.When the exposure is removed then the SB shall transit back to its original state before SB Protection mode. Audio shall be UN-muted and illumination shall be set to its actual state. All functional units shall start at the last state, position and volume.GIS-10A-017 Functionality While in Over Voltage (18 V to 26.5 V)Under the exposure of supply voltage from 18 V to 26.5 V the SB shall be reset and forced into SB protection mode (reference section GIS-10A-021). When the exposure is removed then the SB shall transit back to its original state before SB Protection mode. Audio shall be UN-muted and illumination shall be set to its actual state. All functional units shall start at the last state, position and volume.GIS-10A-018 Functionality While Under Reverse Voltage (0V to 14V)All functions of the SB can deviate as designed during exposure but automatically return to normal operation after exposure is removed. FunctionsStatusRadio =Not Available GPS* =Not Available CAN transceiver =Not Available Navigation* Not Available -Turn by turn-MAP (video interface available)-Dynamic Navigation -Intersection zoom/stylized iconsAudio (DSP functionality)Not AvailableInt. drives (CD-ROM)Not Available Int. drives (CD-ROM, DVD)*Not Available Update Possibility via Drive*Not Available Back light / illuminationNot AvailableSupport of PersonalizationNot Available *items particular to navigation units only.GIS-10A-019 Functionality While Under Low-voltage Range 9 V to 6 VWhen the voltage drops into the range between 9 V and 6 V the SB shall transit to SB protection mode. From protection mode there shall be a possibility to turn off the unit.All audio shall be muted and the functional units such as tuner and CD are shut down. The display content shall remain frozen and the HMI shall ignore all user input except the possibility to turn off the unit. The illumination will switch off at 0HMI InactiveAccTimerActiveRadioPowerButton activated OR(MuteLine activated ANDNOT (Soft-top Open AND key not present)PowerModeActiveAccTimerActivePowerMode = 0AccTimerActivePowerModeActivePowerMode 0AccTimerActiveHMI InactiveInternal Timer expires ORDriver door = Open1 ORKey in ignition2 = FalseAccTimerActiveAccTimerActiveLocal wakeup according to GIS-10A-027 req #3AccTimerActiveAccTimerActiveMuteLine wakeup Only valid if TimerDoorOverride calibration is enabled Only valid if TimerIgnKeyOverride calibration is enabledGIS-10A-023 Accessory Timer Logic1. The AccessoryPowerTimer shall begin countdown due to one of the followinga. At the start of Vehicle Ignition Offb. Vehicle Ignition is off and radio power button is activatedc. Incoming Phone call from external phone connected via Handy Installation Kit.2.Timer shall be expired wh