锂离子电池专业英语

锂离子电池常用专业英语锂离子电池常用专业英语 一 序号 首字母 英文 中文 1 A aging 老化 2 B battery charger 充电器 3 black fleck 黑斑 4 C cap 盖板 5 capacity density 能量密度 6 capacity grading 分容 7 cathode tab welding 极耳超焊 8 cell 电芯 9 charge capacity retention 荷电 容量 保持 10 checking code 检码 11 concave spot 凹点 12 constant current charge 恒流充电 13 constant current discharge 恒流放电 14 constant voltage charge 恒压充电 15 corrective measures 纠正措施 16 crack 裂纹 17 cut off voltage 终止电压 18 cycle life 循环寿命 19 D dark trace 暗痕 20 degrade 降级 21 dent 凹痕 22 discharge depth 放电深度 23 distortion 变形 24 drape 打折 25 E Electrical and MechanicalServices Department 机电部 26 electrolyte 电解 电解液 27 empaistic 压纹 28 end off voltage 放电截止电压 29 environmentally friendly 对环境友好 30 equipment first inspection 设备首检 31 erode 腐蚀 32 explosion proof line 防爆线 33 F first inspection 首检 34 formation 化成 35 fracture 断裂 36 I inspection 检验 37 insulate 绝缘 38 internal resistance 内阻 39 J jellyroll 卷芯 40 joint 接缝 结合点 41 L laser deflecting 偏光 42 laser reticle 激光刻线 43 laser welding flatwise weld 激光焊接 平焊 laser welding standing weld 激光焊接 立焊 44 leakage 漏液 45 leak checking 测漏 46 leaving out of welding 漏焊 47 limited charge voltage 充电限制电压 48 local action 自放电 49 M margin turnly 翘边 50 measuring the dimension of cells 电芯卡尺寸 51 meet requirement 达到要求 52 memory effects 记忆效应 53 N nick 划痕 54 nominal voltage 标称电压 55 notice board confirmation 看板确认 56 nugget 硬块 57 O obverse 正面 58 open circuit voltage 开路电压 59 over charge 过充 60 over discharge 过放 61 over the thickness 超厚 62 P particle 颗粒 63 PE membrane PE 膜 64 pit 坑点 65 placing cells into the box 电芯装盒 66 point inspection 点检 67 preventive measures 预防措施 68 pricking the tapes 扎孔 69 process inspection 制程检验 70 put the battery piled up 将电芯叠放在一起 71 Q qualified products 合格品 72 quality assurance 质量保证 73 quality control 质量控制 74 quality improvement 质量改进 75 quality match 品质配对 76 quality planning 质量策划 77 R rated capacity 额定容量 78 recharge 再充电 79 refitting the can of cell 电芯壳口整形 80 requirment 要求 81 reverse 背面 反面 82 rework 返工 83 ringing cells into pyrocondensation films 套热缩膜 84 S safety vent 安全阀 85 sand aperture 砂眼 86 scar 疤痕 87 secondary battery 二次电池 88 select appearance 选外观 sharp set 批锋 89 short circuit checking 测短路 90 smudginess 污物 91 spot welding by laser 激光点焊 92 spot welding place 点焊位置 93 spraying the code 喷码 94 spur 毛刺 95 sticking the PVC cover boards 贴面垫 96 storing 陈化 97 storing with high voltage 高压储存 98 T tabs deflection 极耳歪斜 99 tabs excursion 极耳错位 100 technics requiment 工艺要求 101 U ultrasonic welding 超声波焊接 102 ultrasonic welding strength 超焊强度 103 unqualified products 不合格品 104 W wave 波浪 105 working procedure 工序 二 盖板 cover board 底板 solepiece 钢珠 steel ball 压钢珠 press steel ball 防爆阀 valve preventing explosion 大电流 倍率 放电 discharge in high rate current 标称电压 Normal voltage 标称容量 normal capacity 放电容量 discharge capacity 充电上限电压 limited voltage in charge 放电下限电压 terminating voltage in discharge 恒流充电 constant current charge 恒压充电 constant voltage charge 恒流放电 constant current discharge 放电曲线 discharge curve 充电曲线 charge curve 放电平台 discharge voltage plateau 容量衰减 capacity attenuation 起始容量 initial discharge capacity 流水线 pipelining 传送带 carrying tape 焊极耳 welding the current collector 卷绕 wind 叠片 layer 贴胶带 stick tape 点焊 spot welding 超声焊 ultrasonic welding 三元素 Nickle Cobalt Manganese Lithium Oxide three elements materials 钴酸锂 Cobalt Lithium Oxide 锰酸锂 Manganese Lithium Oxide 石墨 graphite 烘箱 oven 真空烘箱 vacuum oven 搅拌机 mixing device vacuum mixing device 涂布机 coating equipment 裁纸刀 paper knife cutting knife 分条机 equipment for cutting big piece to much pieces 辊压机 roll press equipment 电阻点焊机 spot welding machine 超声点焊机 ultrasonic spot welding machine 卷绕机 winder 自动叠片机 auto laminating machine 激光焊机 laser welding machine 注液机 infusing machine 真空注液机 vacuum infusion machine 预充柜 pre charge equipment 化成柜 formation systems 分容柜 grading systems 测试柜 testing systems 内阻仪 battery inner resistance tester 万用表 multimeter 转盘式真空封口机 turntable type vacuum sealing machine 自动冲膜机 automatic aluminum membrane shaper 锂离子电池设计专业英语锂离子电池设计专业英语 Capacity 容量 Battery Thickness 电池厚度 Battery width 电池宽度 Battery length 电池高度 Impedance 内阻 Can thickness 壳体厚度 Can wall thickness 壳体壁厚 Can bottom thikness 壳体底部厚度 Can lid thickness 壳体盖板厚度 PP film thickness PP 胶厚度 Ni AL tab thickness Ni Al 极耳厚度 Battery width 电池宽度 Can width margin 电池宽度留边 Can length 壳体长度 Can cross area 壳体体积 Winding pin width 卷针宽度 Can Side residue 壳边残余 Naked battery thickness 裸漏电池厚度 Naked battery width 裸漏电池宽度 Naked battery length 裸漏电池高度 Cathode formulation 阴极含量 Cathode material specific capacity 阴极克比容量 Cathode 阴极装填 Cathode area density 阴极面密度 Cathode bulk density 阴极体积密度 Cathode weight 阴极重量 Cathode thickness 阴极厚度 Cathode elongation rate 延伸率 Cathode actual length 阴极实际长度 Cathode design length 阴极设计长度 Cathode width 阴极宽度 Cathode Scratched area width 阴极涂片宽度 Al foil density 铝箔密度 Al foil thickness 铝箔厚度 Cathode weight 阴极重量 Separator thickness 隔离膜厚度 Separator length 隔离膜长度 Separator width 隔离膜宽度 Separator density 隔离膜密度 Separator weight 隔离膜重量 Anode formulation 阳极含量 Anode material specific capacity 阳极克容量 Anode loading 阳极装填量 Anode area density 阳极面密度 Anode bulk density 阳极体积密度 Anode thickness 阳极厚度 Anode length 阳极长度 Anode width 阳极宽度 Anode scratched area width 阳极刮粉区宽度 Cu foil density 铜箔密度 Cu foil thickness 铜箔厚度 Anode weight 阳极重量 Cathode Tab length 阴极极耳长 Cathode Tab width 阴极极耳宽 Cathode Tab thickness 阴极极耳厚度 Anode Tab length 阳极极耳长度 Anode Tab width 阳极极耳宽度 Anode Tab thickness 阳极极耳厚度 Adhesive tape Length 胶带长度 Adhesive tape Width 胶带宽度 Adhesive tape thickness 胶带厚度 Assembly adhesive tape 装配胶带 Bottom length 底部长度 Bottom Width 底部宽度 Bottom Thickness 底部厚度 Top length 顶部长度 Top Width 顶部宽度 Top Thickness 顶部厚度 Welding length 焊接长度 Welding Width 焊接宽度 Welding Thickness 焊接厚度 Electrol