




全文预览已结束
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
Honeywell Sensor传感器技术资料en1b0221ge51r0902 E7003A II EE7003A10083-PHASE POWERAND ENERGYMETER INSTALLATIONINSTRUCTIONS GENERALINFORMATION Readthese pagescarefully beforeinstalling andoperating the unit.The unitdescribed hereis intendedfor useby properlytrained personnel,only.Maintenance and/or repairsmust becarried outby authorized personnel,only.For proper,safe useof the unit andfor maintenanceand/or repair,it isessential that the personsinstructed tocarry outthese proceduresfollow normalsafety precautions.BEFORE INSTALLATIONThis unitwas manufacturedand testedin pliancewith class2IEC1010and VDE411standards,in aordancewith groupB VDE0110standards foroperating voltagesup to250VACrms phaseto neutral.To maintainthis conditionand toensure safeoperation,the usermust plywith theindications andmarkings containedin thefollowing instructions:Before beginninginstallation,check toensure thatthe unit is intactand thatno damagewas incurredduring shipping.Ensure thatthe mainsvoltage correspondsto the units operatingvoltage and then proceedwith theinstallation.The power supply does not requirean earth connection.A30mA slowfuse shouldbe installedin the power supply circuit to the unit.Maintenance and/or repairsmust becarried outby qualified,authorizedpersonnel,only.If thereis everthe suspicionthat safeuse isno longerpossible,the unit must bedisconnected andprecautions mustbe takenagainst aidentaluse.Operation isno longersafe when:?there areclearly visibledamages;?theunitno longerfunctions;?after aprolonged storagein unfavorableconditions;?after seriousdamages incurredduring transport.INSTALLATION PowerSupply The unitmusthave apower supplywith voltageranging from200.240VAC50/60Hz usingmax.cable gauge2.5mm2and attachedto the power supplyterminals(see Fig.1).The unitpower supplydoesnotneed anearthconnection.Theunitrequires theinstallation ofan external30mA slowfuse in thepowersupplycircuit.Honeywell EE7003A10083-Phase Powerand EnergyMetereurope.hbc.honewell.D-71101Sch鰊aichMade inItalyW kWhHoneywell EE7003A10083-Phase Powerand EnergyMetereurope.hbc.honewell.D-71101Sch鰊aichMade inItalyW kWhsingle-phasecurrentthree-phasecurrentN NL1L1L2L3Fig.1.Connecting thepowersupplyNOTE:Use only200.240VAC powersupply.Connecting theVoltage InputsUse cableswith max.gauge2.5mm2and connectthe voltage inputs tothe screwterminals asdepicted inFig.2.Honeywell EE7003A10083-Phase Powerand EnergyMetereurope.hbc.honewell.D-71101Sch鰊aichMade inItalyW kWhL1NHoneywell EE7003A10083-Phase Powerand EnergyMetereurope.hbc.honewell.D-71101Sch鰊aichMade inItalyW kWhNL1L2L3single-phasecurrentthree-phasecurrent Fig.2.Connecting the voltageinputsNOTE:Use onlymax.250Vac phaseneutral voltageinput.EE7003A10083-PHASE POWERAND ENERGYMETER EN1B-0221GE51R09022Connecting theCurrent InputsUse cableswith max.gauge2.5mm2and connectthe current inputs tothe screwterminals asdepicted inFig.3(whereP1andP2indicate theproper orientationof terminalsprimary1andprimary2of the current transformer).HoneywellEE7003A1008L1L2L3P1S1S2P2NpulseoutputHoneywell EE7003A1008L1P1S1S2P2NpulseoutputHoneywell EE7003A1008L1Npulseoutputsingle-phase current,5A three-phase current,5A Fig.3.Connecting thecurrentinputsNOTE:If thecurrent transformerconnection ismistakenly reversed,theunitwill pensateautomatically.Thus,thecurrentinputs willalways becorrect.This featureapplies toreversed voltageconnection,too.However,it isabsolutely essentialthat youfollow thesequence ofphases betweenthevoltageand thecurrent.NOTE:In orderto avoiddamaging theunit and/or endangeringthe operator,the secondarycurrent transformermust alwaysshort circuitwhen it is notconnected.Programming theUnit OperatorControls andDisplay Theprogramming keyis locatedatthebottom left-hand cornerof thefront panel,below the LCD display(see Fig.5).The power key(W)with itsbuilt-in LEDand the energy key(kWh)with itsbuilt-in LEDare locatedtotheright ofit.Powering UpWhen theunit ispowered up,the wordWAITwill firstappear intheLCD display.After afew seconds,thepowerconsumption willbe displayedandtheLED inthe upperright-hand cornerof thepower key(W)will simultaneouslylight up.Programming ModeTo enterthe programmingmode,simultaneously press the programming key andthe energy(kWh)key.The currentlyvalid CT(current transformer)ratio willthen appearintheLCDdisplay.The CT ratio promptedby defaultis5/5.Setting theCT RatioThe CTratio isset bypressing thepowerkey(W)as oftenas necessaryuntil thedesired valueis displayed.Table1presents all29possible CTratios.Table1.Possible CTratios5/580/5300/5800/51800/525/5100/5320/51000/52000/540/5120/5400/51200/52500/550/5150/5500/51250/53200/560/5200/5600/51500/54000/575/5250/5750/51600/5Once theselection hasbeen made,pressthe programming keyto confirmthis valueand toexit theset-up.Zeroing thePower ReadingSimultaneously pressingtheprogrammingkey andtheenergykey(kWh)causes thevalues forboth currentscales tobe zeroed.Disabling theProgramming KeyAfter youhave programmedtheunit,you maywish todisable theprogrammingkey.This canbe doneby cuttingthe jumperlocated underthe upperterminal covernext tothe pulseoutputs(see Fig.4).Honeywelljumperpulseoutputscurrentinputs Fig.4.Jumper(with upperterminal coverremoved)The terminalcovers canbe removedby insertinga screwdriverinto theirleverage slotsand levering/pulling themout.Once thejumper iscut,itisno longerpossible toreset thekWh counteror to change theCTratio.To re-enable programmingfunctions,itisnecessary tore-establish th
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 赤峰市中医院硬脑膜动静脉瘘手术考核
- 2025第三人民医院药品标识管理考核
- 长治市人民医院急性期血压管理考核
- 大同市中医院输尿管狭窄合并结石处理考核
- 清华大学出版社招聘考试真题2024
- 三年级数学下册教学总结及改进方案
- 大同市中医院甲状腺疾病患者教育能力考核
- 阳泉市人民医院经皮椎弓根螺钉置入技术考核
- 运城市中医院骨科伤口护理技能考核
- 上海市人民医院医疗废物分类与处置规范考核
- GB/T 24218.1-2009纺织品非织造布试验方法第1部分:单位面积质量的测定
- GB/T 10357.1-2013家具力学性能试验第1部分:桌类强度和耐久性
- GB 16541-1996竖井罐笼提升信号系统安全技术要求
- GB 10068-2000轴中心高为56mm及以上电机的机械振动振动的测量、评定及限值
- 车辆模型课件
- 游泳训练理论与方法技术要点课件
- 促进深度学习的课堂教学策略专题研究
- 医疗护理品管圈QCC成果汇报之提高住院病人健康宣教的知晓率(问题解决型)
- 水泥厂化验室质量管理手册
- 2021年5月CCAA审核员考试《认证通用基础》真题及答案
- 2022诗词大会经典诗词文化知识竞赛题库150题(含答案)
评论
0/150
提交评论