MCSS安装参数.doc

MCSS PARAMETERSSPEC-90, E311EEPROM SETTING MANUAL VER. 2.5M - 2 - 3 INST = 1 Top floor jobtop floor number ( = 0 )最底层Country AJG10 = NAO, 1 = JAPAN, 2 = ETO控制型号。ENABLE ADO NY(0)0 = DISABLE, 1 = ENABLE是否允许提前开门ENABLE RELEVEL10 = DISABLE, 1 = ENABLE是否允许再平层ADV BRK LIFT00 = DISABLE, 1 = ENABLE ( NOT USED )是否允许提前打开抱闸DBSS PARITY00 = ODD, 1 = EVENCAR NON START20 sMax, permissible time for detecting door zone of next floor when running ( not used )经过两个插板允许的最大运行时间。MAN. DECEL TIME0( not used in Japan )No. of DZ in 1LS1Number of door zone vane in 1LS zone在1ls内，门区插板的数量No. of DZ in 2LS1Number of door zone vane in 2LS zone在2ls内，门区插板的数量Abs. overspd % NOR110%Ultra over-speed detection permissible % at normal running正常运行期间，允许的最大超速。Abs. overspd % INS130 %Ultra over-speed detection permissible % at inspection running检修运行期间，允许的最大超速。Abs. overspd % REC150 %Ultra over-speed detection permissible % at recover running自平层运行期间，允许的最大超速。Abs. overspd % REI150 % Ultra over-speed detection permissible % at reinitialize running复位运行期间，允许的最大超速。Abs. overspd % JPSDO120 %Ultra over-speed detection permissible % at terminal floor running on JPSDOTrack err % NOR25%Actual speed error permissible % at normal and reinitialize running正常运行和复位运行时，允许和实际速度的误差。Track err % INS50%Actual speed error permissible % at inspection and recover running检修运行时，允许和实际速度的误差。Track err % LOW255 %Actual speed error permissible % at relevel and learn running再平层运行和自学习运行时，允许和实际速度的误差。NTSD percent97%Permissible speed at 1LS / 2LS detection ( % of Normal speed )1ls，2ls动作时电梯速度大于该设定值时，执行强迫减速功能（正常速度%）ETSD percent94 %ETSD relay control speed ( % of Nor. speed )ETSD继电器动作速度（正常速度%）Enable ETSD10 = disable, 1 = enable ( relay fault detection )是否有ETSC功能。0=不允许，1=允许PTR drop delay10msTiming for prepare-to-run drop after brake cut-off 0 : spec-90 / E311 60 : sky linearmax. abs. overspd10permissible number of recovery from max. over-speed error超速后，允许启动次数。max. track retry50permissible number of recovery from tracking error速度误差后允许启动次数。max. NTSD faults10permissible number of recovery from NTSD faultNTSD动作后，允许启动次数。max. ETSD faults10permissible number of recovery from ETSD faultETSD动作后，允许启动次数。max. tract loss1permissible number of recovery from traction loss error.允许启动次数。max. UX, DX fault50permissible number of recovery from U / D relay errorU/D继电器故障允许启动次数。max. pos faults50permissible number of recovery from position fault位置丢失允许启动次数。max. PVT faults50permissible number of recovery from PVT faultPVT故障允许启动次数。max. ADO retries 50permissible number of recovery from ADO faultADO故障允许启动次数。max. EES faults0EES fault ( not used in Japan )允许启动次数。max. rdyrun timeout50permissible number of recovery from ready-to-run timeout error允许启动次数。max. brake timeout50permissible number of recovery from brake lift / drop timeout error允许启动次数。max. adv. brk flt0Advanced brake lift fault ( not used )允许启动次数。max. drive fault50 permissible number of recovery from drive faultNote: permissible number of recovery becomes limitless when 0 is set允许启动次数。max. relevel run5permissible number of relevel ( limit of continuous relevel on the same floor )允许启动次数。measure task no.0for technical test ( not used on the spot ) PROFILE = 2 mm/sVelocity normaljobmax. velocity at normal running正常速度Acceleration normaljobmax. acceleration at normal running正常加速度Jerk normaljobmax. jerk at normal running正常圆角velocity inspection400max. velocity at inspection running检修速度Accel. inspection200max. acceleration at inspection running检修加速度velocity learn100max. velocity at learn running井道自学习速度accel. learn500max. acceleration at learn running井道自学习加速度velocity relevel30max. velocity at relevel running自平层速度accel. relevel300max. acceleration at relevel running自平层加速度velocity recover 100max. velocity at recover running再平层速度accel. recover500max. acceleration at recover running再平层加速度velocity slow100medium velocity at deceleration and reaching to floor at reinitialize running复位时爬行速度 数值在复位速度和再平层速度之间velocity reinitjobmax. velocity at reinitialize running复位运行速度accel. reinitjobdeceleration from 1LS / 2LS at reinitialize running复位运行加速度accel. NTSDjobdeceleration for velocity limit at NTSD for calculating the set distance of 1LS / 2LSNTSD加速度Jerk timedjobmax. jerk for forced deceleration and stoppingVELOC profile 2jobmax. velocity for secondary fire fighting operation of emergency elevatorACCEL profile 2jobmax. acceleration for secondary fire fighting operation of emergency elevator.JERK profile 2jobmax. jerk for secondary fire fighting operation of emergency elevator.Note : VELOC 2, ACCEL 2, JERK 2 are set in the same way as the set value at normal running. Provided that only VELOC 2 is set to 1500 mm / s for models having a normal velocity of 1750 mm / s.VELOC profile 3jobmax. velocity of earthquake control operation for nonstop floors.ACCEL profile 3jobmax. acceleration at earthquake control operation for nonstop floors.JERK profile 3jobMax. jerk at earthquake control operation for nonstop floors.Note : Job which has nonstop floors that elevator cannot decelerate or stop within 10 seconds is used at earthquake control operation. ACCEL3 and JERK3 are set in the same way as the set value at normal running and VELOC to 750 mm / s. For models having 500mm/s, VELOC is set to 500 mm/s .velocity zero5velocity to be judged as stopping( site final adjustment value 3 mm/s )零速（建议2m/s）JPSDO type20 : T = JPSDO for only top terminal1 : T = JPSDO for only bottom terminal2 : T = JPSDO for all terminalvelocity JPSDOjobterminal floor velocity of JPSDONote: set terminal floor velocity for w / JPSDO job only. JPSDO not functioned when set to 0.gain fixed posct20gain value of fixed gain position control at deceleration and stopping 10 / s 位置增益,如果设置得太大，停车时会有振动感delta TC ms 30Control delay time due to delayed discrete input ( DZ sensor, etc )该参数用于限制减速度调节过头。该参数一般设置为30ms。decel / accel %100 %percentage of deceleration to accelerationdestination lead0 mmvalue to adjust target stopping position to this side of the leveldestination lag5 mmvalue to adjust target stopping position to beyond the levelSite final adjustment value ( 3 mm )level tolerance5 mmdistance to be judged as the levelSite final adjustment value ( 3 mm )zero speed time 0 mstime from zero velocity detection to brake cut-off command零速保持时间。BKL to MOV timeout0 mstime from brake release completion to start of velocity command output ( x10 ms )position misplmt0 mmpositional error correction value due to delayed input response of DZ1 / DZ2该参数用于调整门区开关的滞后。1LS/2LS tolerance200 mm tolerance of fitting position detection distance of 1LS / 2LS1LS/2LS允许误差slippage tolerance 200 mmtolerance of detection distance due to rope slippage and vane position钢丝绳允许滑移量counts per revolutionpprrated pulse number of PVT1024 spec-902500 sky linear编码器额定脉冲数motor speedjobmotor speed ( rpm ) at rated velocity马达额定转速 LANDINGS = 3 Front and back door control and setting of floors to which elevator is arrivable.Set to 1 for floor which has a opening on that floor.Set to 0 will disable door opening on that floor. LOAD = 4 Load device type 0 : Spec - 900 : corresponding to switch input of DISS,- sends LOAD VALUE % to DBSS- sends LOAD STATUS to OCSS1 : E311 VF1 : corresponding to LOAD amount of LWT sent from ADISS,- sends LOAD % to DBSS- sends LOAD STATUS to OCSS2 : Sky Linear2 : adding imbalance amount to LOAD amount of LWT sent from ADISS,- sends LOAD % to DBSS- sends LOAD STATUS to OCSS3 : corresponding to LOAD amount of LWT sent from ADISS,- sends bias torque amount to DBSS, ( 127 % )- sends LOAD STATUS to OCSS.NOTES :OCSS load info0 : sends value from device type to OCSS.1 : sends always LOAD DEFAULT to OCSSDBSS load info0 : sends value from device type to DBSS1 : sends always balance load value to DBSS- ANS load % 0 %not input to DISS- Default value %25 %load percent sent to DBSS when LWX input by DISS- Peak load value 0 %not input to DISS- Full load value %50 %Load percent sent to DBSS when LNS inputby DISS- overload value80 %Load percent sent to DBSS when LWO input by DISSNote : These values are set to use DISS switch input for bias torque to DBSS.- offset adjustNo load correction of LWT ( sends to DISS )- Gain adjustMax. load correction of LWT ( sends to DISS )- Imb. comp. factordifference of measurements of bottom and top floorat full load.- % overbalanceOver balance value of car and counterweight45 % : Spec - 90 / E 311 VF47 % : Spec 90 a w /o Mexico50 % : Sky LinearNotes LWT : Load weighing TransducerWhen load device type is 2, offset adjust and, gain adjust imb, comp. factor are automatically adjusted by learning function but can also be set, changed or finely adjusted manually. ( see service tool manual LMCSS_SVT_V25 )Notes on job settingFactory set distance from terminal floor level of 1LS / 2LS and SS1 / SS2 switch is calculated from the following equation :NTSD ( 1LS / 2LS ) set distance = ( velocity normal mm /s ) 2 - 2 x ( accel NTSD mm /s2 )ACCEL NTSD generally has the same value as ACCEL NORMAL set, and a 10-mm order figure of the obtained value is raised for setting.ETSD ( SS1 / SS2 ) set distance = ( velocity normal mm/s x ETSD % ) 2 - 2 x ( accel reinit mm/s2 )For models generally has the same value as ACCEL NORMAL + 200 mm/s2 set, and 10mm or smaller of the value is discarded for setting. For slow velocity models ( 500 mm/s ) and E311 VF, the value is set to be smaller so as not to interfere with NTSD ( 1LS / 2 LS ) switch.ENABLE ADO ( advance door open ) is added only when required by abstract sales order,SKY LINEAR / E311VF needs adjustment on the spot as it uses load weighing transducer ( LWT ).Motor speed of SKY LINEAR is a number of revolution of PVT at a constant velocity and was calculated from the following equation :motor speed ( TLIM ) = velocity normal (mm/s) x 60 - ( rpm ) PVT roller dia. (mm) x pPVT roller dia. = 116 mmFor service job with JPSDO ( terminal floor forced deceleration function ), JPSDO SPEED is set with a velocity slower by one level from each VELOC. NORMAL ( 1750 1500, 1500 1000, 1000 750, 750 500 mm/s ). In this case, for ACCEL and JERK, NORMAL value is applied.And the set distance of 1LS/2LS and SS1/SS2 is a distance determined at normal velocity.For emergency elevator, a velocity at secondary fire fighting operation is specified by VELOC, ACCEL and JERK of profile 2.Velocity normal ( mm/s )VELOC profile 2 (mm/s )ACCEL profile 2 ( mm/s )JERK profile 2 ( mm/s3)5005004004007507505005001000100060060015001500700700175015007007002000150080080025001500800800Velocity which is used at earthquake control operation by job which has such many nonstop floors that elevator cannot decelerate or stop within 10 seconds is specified by VELOC, ACCEL of JERK of profile 3.Velocity normalVeloc profile 3accel profile 3jerk profile 350050040040075075050050010007506006001500750700700175075070070020007508008002500750800800For profile 2 and profile 3, all models have a set value corresponding to a rated velocity set at factory.As E311 VF is a geared elevator and compensation chain ( 6 x 2 - WF20 2.98 Kg/m ) is used, so that imbalance for each floor is not taken into account for bias torque to DBSS.Set value for each duty1. Set value for Spec-90 ( 13 VTR )Duty No.VelocNormalmm/sAccel.Normalmm/s2JerkNormalmm/s3Motorspeed(rpm)AccelNTSDmm/s2 VelocReinitmm/sAccelReinitmm/s2JerkTimedmm/s31LS /2LS setpos. mmSS1 /SS2pos.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et value for Spec-90 ( 13 VTR / 17 CT )Duty No,Veloc.normalmm/sAccelnormalmm/sJerk normalmm/sMotorspeed( rpm )AccelNTSDmm/s2Veloc.Reinitmm/sAccelReinitmm/s2Jerktimedmm/s31LS /2LSset pos.mmSS1/SS2set pos.mmJ13VTA0007A7505005001110500500700700570370J13VTA0008A10006006001171600600800700840600J13VTA0009A1500700700901700100090070016101200J13VTA0010A17507007001051700130090070021901690J13VTA0018A10006006001171600600800700840600J13VTA0019A1500700700901700100090070016101200J13VTA0022A7505005001110500500700700570370J13VTA0023A10006006001171600600800700840600J13VTA0024A1500700700901700100090070016101200J13VTA