车载冰箱标准中英版.doc

Q/SQR.04.*2006Q/SQRIssued by Chery Automobile Co., LtdCarried out on 2007-01-01Issued on 2006-12-15Semiconductor cooler & warmer box（trial implementation）Q/SQR.04.*2006Chery Automobile Co., Ltd Enterprise Standardschool), 4 4 house building as well as more than 1000 copies of books, more than 10 kinds of collection of newspapers and magazines, fires burnt down. In 1938, the Japanese learned that the national Government established in XI Tang Tomb rotten clip taxes, tax officers live in 8 of Yan Dong village farmers home, troops at night, Yao was burned several houses. 1938 new morning of September 18, the Japanese team went to the countryside sweep from the kaiyang village line to Tung Yang Jia Qiao yan Temple wall and met Yang Jia溇 Zhou Dana (male) weeks because of long-term illness and cant work in the fields, the Japanese see his face from scratch without calluses, regard him as Shina, thrust a knife at the scene of his death. The body was stabbed 7 times, wound 13. The same day, Trang bang village heard the Japanese come to mop-up are hiding, mother of 9 Zhou Guanbao Zhang Aying to drill a dry mound, was discovered by the Japanese, a shot in the end. The same day, is 7 zhouhaijiangzhi grandfather Zhou Yingbao to escape the Japanese army, was found on the road, a shot in the end. In March 1939, the Japanese army in Yan Tomb raiding, has arrested 16 people, in fengqiao cigarettes this morning bang, killing 11 people on the River, East meeting point in wood qiaotu in the afternoon killing 4 people on the Riverside. Gu Tong is a Japanese go speak the Shanghai dialect, later to be called Gu Tong as kill left. On January 18, 1943, the elves, five thousand or six thousand, water and land go hand in hand mop-up jiaxing area west of the railway, Yan Tomb area fall. March 6, Niu Shan (County Government II section chief) carrying its child Niu Jun (strict Tomb seventh district Chang) and the District Assistant Yu Xuchu, and players Jin Fuqin, and Shen Baosheng, six people received Wujiang underground County Government notificationPrefaceThe establishment of the standard is referring to related National Automotive Standardizations.The standard is established under the premise to satisfy Chery Auto product performance requirement and regarded as companys basis to develop new product, test product quality and test product performance. Meanwhile its format and content shall be subject to GB/T1.1-2000、GB/T1.2-2002.本标准的编制参照国家汽车行业相关标准。本标准是在满足奇瑞汽车产品性能要求前提下制定的，作为公司开发新产品、检验产品质量以及试验产品性能的依据。同时在格式和内容的编排上均符合GB/T1.1-2000、GB/T1.2-2002的规定。Proposed by: 本标准由*提出。本标准由*归口。Prepared by the unit: 本标准起草单位：Main Drafter: 本标准主要起草人： Semiconductor Cooler & Warmer Box（Trial Implementation）1 Scope This standard stipulate the needed performance, technical requirement, test and trial method, mark, label and package for semiconductor cooler & warmer box. 本标准规定了半导体冷暖箱所需满足的性能、技术要求、检验和试验方法、标志、标签和包装。This standard shall be applied to the semiconductor cooler & warmer box produced by Chery company (Hereinafter referred to as the “Cooler & Warmer Box“)本标准适用于奇瑞公司所产汽车的半导体冷暖箱（以下简称冷暖箱）。2 Documents Cited by this Standard规范性引用文件The terms listed in the following documents which cited by this standard shall be the terms of this standard. For the cited documents which marked with the date, all the later amended ones(exclude correct printing errors content) and revised versions shall not be applicable to the this standard. The latest version which unmarked with date shall be applicable to this standard. 下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。QBT2452-99 Cold and hot water fountain machine light industry standard冷热饮水机轻工行业标准GB4798.1-4798.2 Environmental conditions, storage, transportation existing in the application of electric and electronic products 电工电子产品应用环境条件、贮存、运输Q/SQR.04.057 CAC-Brand Mark CAC-商标标记Q/SQR.04.058 Automobile parts mark requirement 汽车零部件标记要求Q/SQR.04.112 Product outer pack mark requirement 产品外包装标志要求3 Term3.1 Semiconductor Cooler & Warmer BoxThe box with cool and warm change switch use semiconductor to refrigerate and warm and is powered by electricity. 一个利用半导体作为制冷、制热器件，用消耗电能的手段来制冷或制热。并具有冷热转变的开关的箱体。3.2 Top Open Model顶开式：The box body that can be use to put and get the food(stored food) by the top box door or cover.通过顶部的箱门或盖取放食物(贮藏食物)的箱体。3.3 Vertical Model 直立式：The box body that can put and get food (stored food) by front box door.通过前面的箱门取放食物(贮藏食物)的箱体。4 Content内容The semiconductor cooler & warmer box shall be subject to the requirement of this standard and it shall be produced according to product drawing and design that approved by the established procedure. 半导体冷暖箱应符合本标准的要求，并按照规定程序批准的产品图样及设计文件制造。The working temperature ranges from 4090 冷暖箱工作范围温度在4090。4.1 Test Condition (Except different regulation) 试验环境（除非有不同的规定）Temperature： （253）；Atmospheric Pressure大气压力： 860 mbar1060 mbar；Relative Humidity相对湿度： 45%70% ；4.2 General Requirement一般要求4.2.1 MarkThe mark shall be subject to Q/SQR.04.057、Q/SQR.04.058. The mark must be clear and can not be erased; the location of the mark shall be stipulate in the drawing. 标记必须清晰且不可消除，标记所处的位置应在图纸上规定。4.2.2 Dimension and tolerance. 尺寸与公差According to related drawing and/or refer to the basic sample. 根据相关图纸规定和/或参照基本样品。4.2.3 Material材料According to related drawing and/or refer to the basic sample.4.2.4 Surface Painting表面涂装4.3 According to related drawing and/or refer to the basic sample.4.4 Design Speciality设计特性4.4.1 Technical Requirement技术要求 Appearance Requirement外观要求The surface of box body shall be flat, clean, same color, and shall not have scratch, crack, crinkle, deflated, distortion, etc defects. The liner shall not have draw trace, crack and same color without oil dirt. 箱体表面应平整、光洁、色泽一致，不应有划痕、裂纹、起皱、缩瘪、变形等缺陷；内胆应无拉痕、裂痕、色泽一致和无油污等。 Structure Design Requirement结构设计要求The design of cooler & warmer box shall prevent the refrigeration and warm assembly parts from being damaged under normal use. The parts which maybe replaced shall be mounted at the part that easy for operation, replacement and safe. 冷热箱设计时，制冷、制热组件应防止在正常使用时受到损坏。对有可能要更换的元件，如开关、温控器等设计时应考虑安装在便于操作、更换和安全的地方。4.4.2 Performance Requirement 性能要求 Refrigeration Performance制冷性能After working 30 minutes, the temperature inside of box centre lows more than 18. And in two hours the temperature lows more than 23. 工作30分钟后，箱内中心点温降18以上，两小时内温降23以上。 Warming Performance 制热性能After working 15 minutes, the temperature inside of box centre reaches to 655. 工作15分钟内箱内中心点温度到达655。 Over-temperature Protective 过温保护Over-temperature Protective and self-recovery 过温保护与自动恢复：When warming, the over-temperature protective occurs when the temperature of the middle point of front refrigeration piece reaches over 655 and the power cut off automatically. The power will resume when the temperature lows to less than 555. (The maximum of digital display is 60 when warming) 制热时箱内前端制冷片中间点超过655时，过温保护，此时电源自动关断；当温度降至555时，电源自动恢复。（制热时，数码显示最大为60） Display Model显示方式 The冰箱 working condition is displayed by green and red LED lights.的工作状态有绿色及红色两个LED显示。 The green LED shows the refrigeration condition and red LED shows the warming condition. The temperature inside of box is showed by digital display.( Temperature error 3, minimum temperature display is -9 when cooling) 绿色LED为制冷状态指示，红色LED为制热状态指示。箱内温度有数显指示（温度误差3度，制冷时最低显示温度-9）。4.5 Test Method试验方法4.4.1 Measuring Instrument测量仪器 Temperature Measuring Instrument 温度测量仪器 The accuracy degree of the temperature measuring instrument equipment and thermocouple shall be the same. 温度测量仪器应采用精度等级与热电偶同等精度的测量装置。 Humidity Measuring Instrument湿度测量仪器 Relative humidity measureing adopts catathermometer. 相对湿度采用干湿球温度计。 Electric Appliance Measuring Instrument电器测量仪器 The accuracy is not less than 0.5 degree by DC voltmeter 直流电压表型式试验时准确度不低于0.5级4.4.2 Life Test寿命测试 Life of 冰箱 冰箱的寿命The life of cooler & warmer box can be calculated by the formula: Every day working 4 hours Every week 7 days50 weeks 2 years=2800 hours。The life test is made for working continuous 5000 hours.冷暖箱的使用寿命用以下公式计算：每天工作4小时每周7天50周2年=2800小时。实际按连续工作5000小时做寿命测试。实际按连续工作5000小时做寿命测试。 Life of Switch开关的寿命The life of power switch can be calculated by the formula: Everyday turns on and off for 4 times Every week 7 days50 weeks2years=2800 number of times。The switch is required can be used for 3500 times 电源开关寿命用以下公式计算：每天开关4次每周7天50周2年=2800次。要求开关能达到3500次的开关寿命。4.4.3 Temperature Test 温度测试 Test order is test refrigeration first then test warming. 测温顺序为先测制冷后测制热。 Refrigeration Test 制冷试验Under the condition of circumstance temperature (253) , temperature probe is put into the centre of cooler & warmer box and box door open for more than 2 hours, then close the door ,turn on the power and check the box inside temperature shall be subject to the term 在环境温度(253) 条件下，将测温计的感温头放在冷暖箱的中心处，将冷暖箱门打开放置2小时以上，关闭冷暖箱门，接通电源，检查箱内温度应符合条规定。 Warming Test 制热试验Under the condition of circumstance temperature (253) , temperature probe is put into the centre of cooler & warmer box and box door open for more than 2 hours, then close the door ,turn on the power and check the box inside temperature shall be subject to the term 在环境温度(253) 条件下，将测温计的感温头放在冷暖箱的中心处，将冷暖箱门打开放置2小时以上，关闭冷暖箱门，接通电源，检查箱内温度应符合条规定。4.4.4 Vibration Test振动试验 The cooler & warmer box can meet the performance requirement after being installed and tested according to the condition listed in the form as below. The cooler & warmer box is empty and under off working state. 冷暖箱按实际使用状态安装、按下表中给出的条件进行试验后，仍能满足功能要求。进行振动试验时，冷暖箱应处于不工作状态，冷暖箱内是空的。ItemTest ConditionVibration Frequency Hz33Vibration Acceleration m/ s229.4Vibration Direction Up and DownLeft and RightFront and BackVibration Time h422Remark: 1) Vibration amplitude is 0.5mm，when resonance under 33Hz the vibration acceleration shall select 29.4m/s2 and avoid to make the same test on the resonance point. 下出现共振时，振动加速度应选为29.4m/s2，且要避开共振点进行同样试验。2) The test point of vibration acceleration shall be the part where the washer mounted on the bracket. 振动加速度的测定点应取清洗器在支架上的安装部分。 4.4.5 Temperature Cycle Test温度循环试验First, make the test for 3 hours und