华为MA5680T开局指导.doc

MA5680T的版本：VERSION : MA5600V800R008C01 PATCH : SPC200 SPH307 HP2107开局前的准备工作：board add 0/1 H802EPBD EPBD pon业务板注册到1号槽位，业务板型号H802EPBD可以通过命令display board 0查看，注册后再通过命令display board 0查看，此时业务板的状态由auto_find转变为Normal（业务板需要手工注册，主控板不需要手工注册）interface epon 0/1 打开Pon板的QinQ功能 vlan-range enablelink-aggregation 0/7 0-1 egress-ingress 将7号槽位的0和1口进行端口绑捆（镇海用的是业务主控板实现端口绑捆并上行至S9303交换机）,配置成功后，在设备的配置表现形势为：link-aggregation 0/7 0 egress-ingress link-aggregation add-member 0/7/0 0/7 1 与配置时不一样。1. 创建DBA模板（用于onu上行带宽控制，无论OAM或SNMP注册ONU都需要创建DBA和线路模板）DBA只是限制ONU上行的带宽，默认情况下没有对ONU下行进行带宽限制。CG_MA5680T (config)#dba-profile add profile-id 10 profile-name 10M type2 assure 10240 创建保证带宽为10M的DBA模版2. 创建线路模板CG_MA5680T(config)#ont-lineprofile epon profile-id 1 profile-name “test1” CG_MA5680T(config-epon-lineprofile-1)#llid dba-profile-id 10 引用dba模版CG_MA5680T(config-epon-lineprofile-20)#commit 提交生效如果没有在线路模板下配置DBA模版，那么默认调用DBA模板1，DBA1模板限制上传带宽5Mbps。3. 创建业务模板CG_MA5680T(config)#ont-srvprofile epon profile-id 1 profile-name test1 CG_MA5680T(config-epon-srvprofile-1)#ont-port eth 4 定义ONU端口数，也可以认为是定义ONU的类型，格林耐特定义ONU一般是4口类型。CG_MA5680T(config-epon-srvprofile-1)#commit 提交生效4. 创建vlan并在上行口做透传CG_MA5680T (config)#vlan 21 standard 创建网管vlan 21CG_MA5680T (config)#vlan 3999 smart 创建电信上网vlanCG_MA5680T (config)#vlan 3610 smart 创建移动上网外层vlanCG_MA5680T (config)#vlan 300 smart 创建点播vlanCG_MA5680T (config)#vlan attrib 3610 q-in-q 设置移动上网外层VLAN QinQ属性CG_MA5680T (config)#port vlan 21 0/7 0 将7号业务板的0号GE口透传VLAN，因业务板的0和1口成功建立端口绑捆，所以只配置0号口，1号口会自动加入。CG_MA5680T (config)#port vlan 3999 0/7 0CG_MA5680T (config)#port vlan 3610 0/7 0 CG_MA5680T (config)#port vlan 300 0/7 0 上行口透传olt上所有vlan5. 通过OAM方式注册onuCG_MA5680T (config)# interface epon 0/1CG_MA5680T(config-if-epon-0/1)# port 0 ont-auto-find enable 开启0/1/0端口的ONU自动发现功能，可以查看自动发现ONU的MAC地址，同时也可以查看Pon板下自动发的但没有注册的ONUCG_MA5680T(config-if-epon-0/1)# ont add 0 mac-auth 0018-0001-0001 oam ont-lineprofile-id 1 ont-srvprofile-id 1 desc CeShi_ONU在0号PON口增加MAC为0018-0001-0001的ONU，注册方式为:OAM，线路模板为1，业务模板为1，描述为“CeShi_ONU”；建议ONU的描述能够加入管理IP地址。添加描述信息可选，增加第二台时注意更改ontid号，从0开始依次增加就行，如果不写会自动排序，如果要指定onuid号需要直接输入onuid号，如：ont add 0 1 mac-auth 0018-0001-0001 oam ont-lineprofile-id 1 ont-srvprofile-id 1 desc CeShi_ONUCG_MA5680T(config-if-epon-0/1)# ont port native-vlan 0 0 eth 1 vlan 240把0号PON口下的0号ONU的1口设为access vlan 2406. 通过SNMP方式注册ONUCG_MA5680T (config)# interface epon 0/1CG_MA5680T(config-if-epon-0/1)#ont add 0 0 mac-auth 000A-5A14-A907 snmp ont-lineprofile-id 1 desc JiFangCeshi_ONU1 在0号PON口增加MAC为000A-5A14-A907的ONU，注册方式为:snmp，线路模板为1，描述为“CeShi_ONU”CG_MA5680T(config-if-epon-0/1)#ont ipconfig 0 0 ip-address 10.31.0.1 mask 255.255.255.0 gateway 10.31.0.254 manage-vlan 41下发ONU的管理IP和管理VLAN7. 创建业务虚端口CG_MA5680T(config)# service-port vlan 41 epon 0/1/0 ont 0 multi-service user-vlan 41配置ONU管理vlan 41业务虚通道，1号Pon板的0号PON口（0/1代表的1号Pon板），ontid为0CG_MA5680T(config)# service-port vlan 300 epon 0/1/0 ont 0 multi-service user-vlan 300 配置点播vlan 300业务虚通道，1号板的0号PON口，ontid为0CG_MA5680T(config)#service-port vlan 3999 epon 0/1/0 ont 0 multi-service user-vlan 3999 配置电信上网vlan的业务虚通道， 1号板的0号PON口，ontid为0CG_MA5680T(config)# service-port vlan 3610 epon 0/1/0 ont all multi-service user-vlan 1001 to 3499 为1号板的0号PON口下所有onu移动上网vlan创建业务虚通道，打外层标签3610，内层vlan为1001-3499。8保存配置CG_MA5680T(config)#save9.常用命令查看mac地址CG_MA5680T#display mac-address board 0/1- TYPE MAC MAC TYPE F/S VLAN ID - epon 0040-4863-703e dynamic 0/1 240 epon 0040-4863-703f dynamic 0/1 240 epon 0040-4863-703d dynamic 0/1 240 epon 0040-4863-703c dynamic 0/1 240 epon 0040-4863-7038 dynamic 0/1 240清除mac地址CG_MA5680T(config)#undo mac-address mac 000a-5a14-ad17 vlan 61查看自动发现的ONUCG_MA5680T(config)#display ont autofind all查看ONU注册状态CG_MA5680T(config)#display ont info 0 1 1 all - F/S/P: 0/1/1 - ONT-ID MAC Control Run Config Match Protect flag state state state side - 0 000A-5A14-AC8A active online normal match no - Description : ZhenHaiZhongXue - 2 000A-5A14-AA65 active online normal match no - Description : GuangDaYinHang查看0/1下1号PON下所有ONU注册状态查看全局配置CG_MA5680T(config)#display current-configurationCG_MA5680T#display board 0 查看机框所有业务板类型 - SlotID BoardName Status SubType0 SubType1 Online/Offline - 0 1 H802EPBD Normal 2 H802EPBD Normal 3 4 5 6 7 H801SCUN Active_normal 8 H801SCUN Standby_normal 9 -display alarm history all detail 查看所有历史详细告警display alarm history all list 查看历史告警CG_MA5680T#display cpu 0/7 查看主用主控板的CPU利用率 CPU occupancy: 13%CG_MA5680T(config)#display mem 0/7 查看主用主控板的内存利用率 Memory occupancy: 48%CG_MA5680T#display dba-profile ?- Command of privilege Mode:-all All DBA profileprofile-id DBA profile IDprofile-name DBA profile nameCG_MA5680T#display dba-profile all 查看所有DBA模版 - Profile-ID type Bandwidth Fix Assure Max Bind compensation (kbps) (kbps) (kbps) times - 1 1 No 5120 0 0 0 2 1 No 1024 0 0 0 3 4 No 0 0 32768 0 4 1 No 1024000 0 0 0 5 1 No 32768 0 0 0 6 1 No 102400 0 0 0 7 2 No 0 32768 0 0 8 2 No 0 102400 0 0 9 3 No 0 32768 65536 0 10 2 No 0 10240 0 2 -CG_MA5680T#display ont-srvprofile epon all 查看业务模版 - Profile-ID Profile-name Binding times - 1 ChengGuan_VIDEO 20 2 Vlan-Trunk 4 - Total: 2CG_MA5680T#display ont-srvprofile epon ? - Command of privilege Mode:-all Display all ONT service profilesprofile-id By profile IDprofile-name By profile nameCG_MA5680T#display ont-srvprofile epon profile-?- Command of privilege Mode:-profile-id By profile IDprofile-name By profile nameCG_MA5680T#display ont-srvprofile epon profile-id ?- Command of privilege Mode:-profile-id ONT service profile IDCG_MA5680T#display ont-srvprofile epon profile-id 1 ?- Command of privilege Mode:- Please press ENTER to execute command CG_MA5680T#display ont-srvprofile epon profile-id 1 查看业务模版 - Profile-ID : 1 Profile-name: ChengGuan_VIDEO Access-type : EPON - Port-type Port-number - POTS 0 ETH 4 TDM 0 - TDM port type : E1 Multicast fast leave switch : Unconcern Ring check switch : Unconcern - Port Port Up-traffic Down-traffic MAC-learn Class Type ID CAR-ID CAR-ID count profile-ID - ETH 1 Unconcern Unconcern Unlimited - ETH 2 Unconcern Unconcern Unlimited - ETH 3 Unconcern Unconcern Unlimited - ETH 4 Unconcern Unconcern Unlimited - - Port Port-ID Multicast-S-VLAN Multicast-C-VLAN Multicast Multicast Type tag-strip group-num - ETH 1 - - Tag Unlimited ETH 2 - - Tag Unlimited ETH 3 - - Tag Unlimited ETH 4 - - Tag Unlimited - Port-Type Port-ID Service-type Index S-VLAN C-VLAN - ETH 1 - - - - ETH 2 - - - - ETH 3 - - - - ETH 4 - - - - - Binding times : 20 -查看三层VLAN端口CG_MA5680T(config)#display interface |adsl|meth|null|shdsl|vdsl|vlanif :vlanif | :21 Command: display interface vlanif 21vlanif21 current state : UPLine protocol current state : UPDescription : HUAWEI, SmartAX Series, vlanif21 InterfaceThe Maximum Transmit Unit is 1500 bytesInternet Address is 10.3.1.2/30IP Sending Frames Format is PKTFMT_ETHNT_2, Hardware address is 5489-98c1-c9deVLAN Encap-mode : single-tagCG_MA5680T(config)#interface scu 0/7 进入主控板端口CG_MA5680T(config-if-scu-0/7)#display port state all 查看主控板所有端口状态 - Port Port Optic Native MDI Speed Duplex Flow- Active Link Type Status VLAN (Mbps) Ctrl State - 0 GE normal 1 - auto_1000 auto_full off active online 1 GE normal 1 - auto_1000 auto_full off active online 2 GE absence 1 - auto auto off active offline 3 GE absence 1 - auto auto off active offline - Note: For any port, setting MDI to auto-negotiation is invalid, For a 1000 M Electrical port in the full-duplex mode, setting MDI to any value is InvalidCG_MA5680T(config-if-scu-0/7)#display port statistics 0 ? 查看主控板端口流量- Command of scu Mode:- Please press ENTER to execute command CG_MA5680T(config-if-scu-0/7)#display port statistics 0 Number of transmitted frames =3879293281 Number of received frames =1011898734 Total number of frames =4891192015 Number of transmitted multicast frames =2743 Number of received multicast frames =558650 Total number of multicast frames =561393 Number of transmitted broadcast frames =867446 Number of received broadcast frames =3351974 Total number of broadcast frames =4219420 Number of transmitted pause frames =0 Number of