



全文预览已结束
下载本文档
版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
孟加拉PAYRA 2660MW燃煤电厂工程孟加拉PAYRA 2660MW燃煤电厂工程Bangladesh PAYRA 2 x 660 mw coal-fired power plant project搅拌站罐体标识喷漆技术要求Cement tank station logo spraying technical requirements编制: authorized strength: 审核: Reviewers: 批准人员 : authorizing officer:日期date:搅拌站水泥罐标识喷漆技术要求Cement tank station logo spraying technical requirements一、 关于机械化搅拌站水泥罐体公司标识样式选择。About mechanical mixing station cement tank company logo styles to choose from。1 水泥灌体标识样式如下图所示,标识为双面喷涂。The cement tank logo style as shown in the figure below, identified as double-sided spraying。二、 标识尺寸的确定The determination of logo size根据水泥供货厂家提供的水泥罐体直径确定两个标识为上图样式,尺寸皆为弧面长度3.45m*高度1.5m,上部蓝条高度为1.0m,往下区域喷漆高度依次为2.5m、2.5m、2.5m、2.5mm、1.5m。标识采用罐体两面喷涂,并要求居中喷涂。Determined according to cement tank diameter of the cement supplier provides two logo for above style, size of curve length is 3.45 m * 1.5 m, the top blue bar height of 1.0 m, the area under the spray height of 2.5 m, 2.5 m, 2.5 m, 2.5 mm, 1.5 m. Identification by spraying on both sides of tank, Request center spraying三、 罐体喷涂油漆要求tank spray paint requirements1、喷涂前进行表面处理,无凹坑、无夹层,边沿无毛刺,焊接接头、咬边、凸出处要打磨光滑,钢材表面无锈蚀、酸、碱、油脂等污物。For surface treatment before spraying, pits, interlining, edge, no burr, welded joint, bite edge, to smooth out, steel rust, acid, alkali, grease and dirt2、结构件表面喷砂除锈等级应达到Sa2.5级,其它部件表面除锈等级必须达到Sa2级。Structure surface sandblasting derusting grade should reach Sa2.5 level, the other part surface descaling grade must achieve Sa2 level3、油漆干透后漆膜应牢固地粘附在涂面上,不得有发粘、脆裂、脱皮、皱皮、气泡、斑痕及粘附颗粒杂质等缺陷,外观漆膜应均匀、细致、光亮平整、颜色一致,不得有流痕和明显刷痕。After paint dry film adhesion on the coating should be firmly, can not have sticky, embrittlement, peeling, wrinkled skin, bubble, flecked and adhesive particle impurity defects, such as exterior coating should be uniform, delicate, bright, smooth, consistent color can not have flow mark and clear brush marks4、喷涂油漆的标准为底漆两遍、中间漆一遍、面漆两遍,适合防腐要求在20年左右的。Standard for primer spraying paint twice, intermediate paint again, surface paint twice, is suitable for anticorrosion requirements in 20 years or so底漆:环氧富锌底漆,涂布率是2-3平方/公斤,两遍;中涂漆:环氧云铁防锈漆,涂布率是2-3平方/公斤,一遍。 面漆:氯化橡胶面漆,涂布率是4-5平方/公斤,两遍。Primer, epoxy zinc rich primer, coating rate is 2-3 square/kg, twice. epoxy micaceous iron oxide antirust paint, coating rate is 2-3 square/kg, it again. Finish: chlorinated rubber paint, coating rate is 4-5 square/kg, twice配料时应严格按配合比加料或加稀释剂,并使稠度适宜,边配边用。喷涂施工应分遍成活,必须在上一遍基本干燥固化后,再喷涂后一遍。Proportion of ingredients should be in strict accordance with the charging or add diluent, and the consistency is appropriate, preparation and use. Spraying construction should be accomplish step by step, must be in the basic dry again after spraying, after spraying again5、喷涂过程中,操作者应采用测厚针检测涂层厚度,直至达到设计规定的厚度时,方可停止喷涂。油漆干膜厚度保证在180um210um之间。Spraying process, the operator should use coating thickness thickness needle detection, until reach the thickness o
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 2025年矿山安全员考试试题(附答案)
- 2025年焊工取证试题及答案
- 2025年湖北省宜昌市公需课培训(专业技术人员继续教育)试题及答案
- 2025年动物防疫专员考试题库(含答案)
- 2025年爆破工培训试题及答案
- 巴彦淖尔市中医院感染病科研论文写作考核
- 绥化市人民医院微创手术中转开放决策能力考核
- 通辽市人民医院腹膜透析居家护理考核
- 保定市中医院老年肺部感染诊治特点考核
- 2025年医疗技术临床应用论证、管理、评估制度
- 甜水园吉野家餐厅合同7篇
- 2024年蚌埠五河县事业单位选调工作人员考试真题
- 2025年医院领导竞聘面试题与参考答案
- 黑龙江省高等教育教学成果奖申请书
- 2025中矿金石实业有限公司社会招聘备考考试题库附答案解析
- 2025年屠检考务试卷及答案
- 亨利八世课件
- (正式版)DB65∕T 4260-2019 《薰衣草优 质种苗组培快繁生产技术规程》
- 足球绕杆射门课件
- 五金材料知识培训课件
- 新疆兵地联盟2024-2025学年高二上学期期中联考数学试卷(解析版)
评论
0/150
提交评论