电梯翻译参数 修改版

美福电梯的图纸要求1，代码：Code说明：Description轿厢净宽：Car width轿厢净深：Car depth轿厢高度：Car height开门净宽：Door open width开门净高：Door open height门洞净宽：Door hole width门洞净高：Door hole height井道净宽：Shaft width井道净高：Shaft depth顶层净高：Top floor height底坑净深：Pit depth提升高度：Rising height机房净宽：Machine room width机房净深：Machine room depth机房净高：Machine room height轿厢轨距：Car gauge对重轨距：CW gauge主副轨距：Rail gauge主轨前距：Main rail distance额定载荷：Rated capacity 额定速度：Rated speed最大停站数：Max stops最大提升高度：Max rising height最小底坑深度：Min pit depth最小顶层高度：Main top floor height电机功率:Motor capacity电源容量：Power capacity动力电源：Power supply照明电源：Light power supply支撑点受力：Supporting stress 非标说明：Note轿厢尺寸：Car size开门形式尺寸：Door Size2， 井道立面图：Shaft Vertical View底坑受力分布图：Pit stress distribution顶层吊钩位置图：the top hook locations门洞留孔图：Door Hole提升高度：travelling height （TH） 牛腿 ：haunched beam 吊钩：hook；在吊钩处标明：marked on the hook导轨支架每档间隔：ring beam each distance层高：floor height 砼过梁：concrete beam 客户自理：by customer 门高：door height 弹性圆柱销：elastic cylindrical pin 顶层高：overhead height （OH） 控制柜安装孔（仅在顶层处预留，安装后填补）：controller hole reservation(only top floor reserved fill after installation) 机房地面：machine floor 召唤箱孔：calling box 井道壁：shaft wall 缓冲器墩：buffer basement 爬梯：stairs3.门洞净尺寸：net door hole height4.井道右侧立视图： solid view of right side shaft5.导轨支架连接点(圈梁等)间距每档：the spacing of rail bracket connection point (ring beam,etc）/each file6.井道照明间距每盏：shaft lighting spacing / each lamp7.机房平面布置图:machine room plan8.排风扇：exhaust fan 9.通风、采光窗：ventilation、lighting window10.吊钩投影：hook projection11.井道平面布置图：shaft plan12.A/C向留孔：A direction hole reserved drawing13.D视图：D view14.装修后楼面：decorated floor15.安装完成后二次填充：after installing the second fill 16.E向门洞留孔图：E direction/door hole reserved drawing17.底坑平面布置图：pit view请按实际数据填写pls fill in actual dataTRTH5层 5F4层 4F3层 3F2层 2F1层 1F -1层 -1F-2层 -2FPD层站 高度（mm）floor height(mm)_层_站_门 _F_S_D 用户签字盖章处： customer signature日期： date供方签字盖章处： supply signature日期：date合同号：contract No.设备号：Equip No.注：本图需双方签章盖章后生效，本图非按比例绘制，请以标注尺寸为准，全部尺寸单位为mm。Note: this drawing should be signed before using, the drawing is not by scaling, this unit of dimension is mm.变更记录modify notes版本 V.标记mark签名name 日期date变更内容details of change项目名称 project name*工程 Project设计 design 电梯土建总体布置图 elevator construction drawing校对 check图号 draw No.审核 approve共1页 pages 1第1页 page 1比例 scale版本 V.18.注：缓冲器墩由用户配合制作，但在制作前需预置4根12钢筋，伸出坑底300以上，均布在200的圆上。当提升高度大于30m时，缓冲器墩P2按虚线处布置，承载力按单个P2/2计算。Note: Client supply the buffer base, but 412 reinforced bar which distribute on 200 circle,should be prepared, and leave 300mm beyond the pit.when travel height more than30m，buffer base P2 installed according to dotted line,and capacity calculated according to single P2/2.19.用户单位在收到本公司的电梯土建图后，请及时确认，本图需经双方盖章确认后方可生效，如需对确认并双方盖章的土建图更改，则由更改方承担相关责任after the user recieved the construction drawing, please confirm in time, this is effective by signed, if need to correct the drawing, the corrector is in charge20.Technical Requirement(修改版)1、电源要求：需方应将电源送到机房门旁或控制屏预留孔旁墙上，高度约1.5m。 电源为三相五线制、380V、50Hz交流电，允许电压波动为7%，输入总功率需大于主电机总功率50%以上。并配置与电源容量相应的的空气开关。允许附带漏电保护器/功能，但变频调速时需用专用漏电保护开关。接地线的电阻值4， 零线和接地线应始终分开；Power requirement: the buyer should send power to the wall beside machine room door or beside the reserved hole of control screen, the height is about 1.5m. The power is 3 phase 5 line、380V、50Hz DC, and equipped with air switch which can protect from leakage. The allowed voltage fluctuation is 7%, total input power should be more than 50% of main motor power. Grounding wire resistance 4, the neutral wire and grounding wire should always be separated. 2、井道要求：井道应为电梯专用，不得装设与电梯无关的设备(如管道、电缆等)。电梯井道应有效阻止人体进入。井道的平面尺寸是指用铅垂线测得的最小尺寸，允许偏差0+50mm。原则上井道内不得有突出的梁、柱等。井道壁的耐压24MPa。推荐采用全混凝土结构形式制作，并可不设预埋铁。如为实心砖墙结构，应按图设置预埋铁或在预埋铁的水平面上浇制圈梁，高度300mm。如为空心砖墙结构，可选择用C25混凝土灌实墙体，并在预埋铁的水平面上浇制圈梁，高度300mm。当井道前壁为砖墙结构时，应在门洞上方设置混凝土过梁，用于固定厅门支架，高度300mm。如图中有要求，则厅门口应按图浇制能承受额定载重以上承载力的混凝土牛腿。井道内应设永久照明灯，照度50LX， 底坑中缓冲器墩应由需方在电梯安装人员的指导下配合制作，但在制作前应预埋4根插筋，材料12mm，伸出底坑地面300mm，该墩位置下的地面应能承受图中给出的冲击力。底坑应防水。底坑里应有人能到达的空间。底坑爬梯由用户自理， 底坑下面如果有人能到达的空间(如地下室)，应将对重缓冲器墩一直延伸到下面的坚固地面。相邻两个层站的间距11m时，应在中间设置宽350mm，高1800mm安全门。Shaft requirement: the allowed deviation of shaft plan size is 050mm. , there should be no prominent column in shaft, and equipments related to elevator should not exist also. Pressure of shaft wall should be no less than 24MPa. Concrete structure is recommended. If it is solid brick, cast coil beam on the embedded iron or the plane of embedded iron according the drawing, the height should be no less than 300mm. If it is hollow brick, using C25 concrete to make the wall solid, and cast coil beam on the plane of embedded iron, the height should be no less than 300mm. When the front wall of shaft is made of brick, mould a concrete beam above the door hole to fix the landing door bracket, the height is no less than 300mm. Lighting in shaft should be permanent, lighting degree is no less than 50LX. Buyer should mould buffer frusta at the direction of installation member, Ground under this frusta should can support wallop given in the drawing. The pit should be waterproof and have enough room for people to reach. Buyers should prepare ladder by themselves, If the space under the pit can hold people (basement e.g.), the counterweight buffer frusta should be extended to the firm ground. Distance between two floors should be no less than 11m, and a 1800-height and 350mm-width safety door should be set.3、机房要求(无机房电梯不适用)：应考虑适于主机运输的通道。机房内的通风窗、排风扇等需安装完毕，保持机房内相对湿度85%，温度+540。楼板预留孔四周需浇制50mm高翻口。地面应平整，并能承受700kg/m的安装载荷(集中载荷另加)。 Machine room requirement( not applied to machine room less elevator): considering channels which can transport main motor well, After the installation of ventilator and blower, chine room humidity no more than 86%, and machine room temperature is at +540. Cast a 50mm prominent hole around reserved hole of floor. The ground should be flat and can support loading of 70