HP CISCO MDS9124配置.doc

HP CISCO MDS9124配置请先用Console线与光纤交换机控制口（console）相连，开启SecurtCRT，配置连接属性并连接：此时启动光纤交换机，会出现如下画面： MDS-Bootloader-01.00.17 (May 28 2009 - 23:13:36), Build: 01.00.17PowerPC CPU: 8541, Version: 1.1, (SVR:0x807a0011) Core: E500, Version: 2.0, (PVR:0x80200020) Clocks: CPU: 999 MHz, CCB: 333 MHz, DDR: 166 MHz, LBC: 41 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabledINFO: Booting off primary flash.I2C: readyDRAM: Total SDRAM memory is 512 MB20000000INFO: SDRAM tests PASSED.DRAM: ECC initialization in progress.Done.done.INFO: Board rev = 6 type = 4 index 9032L2 cache 256KB: enabledIDE: Bus 0: OK Device 0: Model: SILICONSYSTEMS INC 256MB Firm: 841-023 Ser#: B92431DB5JNW0D06WC0 Type: Hard Disk Capacity: 248.5 MB = 0.2 GB (508928 x 512)Booting bootflash:/m9100-s2ek9-kickstart-mz.4.1.3a.bin .Automatic boot of image at addr 0x00000000 .Starting kernel. Entered kgdb_console_init:1960INIT: version 2.85 bootingChecking all filesystems.r.ERROR: bootflash: has unrecoverable error; please do format bootflash: done./etc/rc.d/rcS.d/S30procps: line 34: log_action_begin_msg: command not found/etc/rc.d/rcS.d/S30procps: line 36: log_action_end_msg: command not foundSetting the System Clock using the Hardware Clock as reference.System Clock set. Local time: Thu Nov 26 01:11:15 UTC 2009Loading system softwareUncompressing system image: bootflash:/m9100-s2ek9-mz.4.1.3a.binCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCINIT: Entering runlevel: 3Starting NFS servers: nfsd mountd.2009 Nov 26 01:11:49 %KERN-2-SYSTEM_MSG: Starting kernel. - kernel2009 Nov 26 01:11:49 %KERN-1-SYSTEM_MSG: Entered kgdb_console_init:1960 - kernel - System Admin Account Setup -Do you want to enforce secure password standard (yes/no) y: 2009 Nov 26 01:12:14 switch %PLATFORM-2-PS_OK: Power supply 2 ok (Serial number PAC132430JE)2009 Nov 26 01:12:14 switch %PLATFORM-2-PS_FANOK: Fan in Power supply 2 ok2009 Nov 26 01:12:14 switch %PLATFORM-2-FAN_OK: Fan module ok输入“no”则对密码强度没有要求，建议直接回车或者输入“y”（要求密码要有8位以上、包含大写字母、小写字母、数字特殊符号中的三种），此时会出现如下画面：Enter the password for admin: 输入密码后要求再次确认（如不符合密码规则，则要求重新输入）。Confirm the password for admin:确认密码后出现以下画面： - Basic System Configuration Dialog -This setup utility will guide you through the basic configuration ofthe system. Setup configures only enough connectivity for managementof the system.Please register Cisco MDS 9000 Family devices promptly with yoursupplier. Failure to register may affect response times for initialservice calls. MDS devices must be registered to receive entitled support services.Press Enter at anytime to skip a dialog. Use ctrl-c at anytime to skip the remaining dialogs.Would you like to enter the basic configuration dialog (yes/no):输入“yes”进行基本配置。 Create another login account (yes/no) n: n Configure read-only SNMP community string (yes/no) n: n Configure read-write SNMP community string (yes/no) n: n Enter the switch name : mds9124 Continue with Out-of-band (mgmt0) management configuration? (yes/no) y: y Mgmt0 IPv4 address : 37 Mgmt0 IPv4 netmask : Configure the default gateway? (yes/no) y: y IPv4 address of the default gateway : 54 Configure advanced IP options? (yes/no) n: n Enable the ssh service? (yes/no) y: yes Type of ssh key you would like to generate (dsa/rsa) rsa: rsa Number of rsa key bits 1024:1024 Enable the telnet service? (yes/no) n: n Enable the http-server? (yes/no) y: y Configure clock? (yes/no) n: n Configure timezone? (yes/no) n: n Configure summertime? (yes/no) n: n Configure the ntp server? (yes/no) n: n Configure default switchport interface state (shut/noshut) shut: noshut Configure default switchport trunk mode (on/off/auto) on: on Configure default switchport port mode F (yes/no) n: n Configure default zone policy (permit/deny) deny: deny Enable full zoneset distribution? (yes/no) n: yesConfigure default zone mode (basic/enhanced) basic: basicThe following configuration will be applied: password strength-check interface mgmt0 ip address 37 no shutdown ip default-gateway 54 no feature ssh feature telnet feature http-server no system default switchport shutdown system default switchport trunk mode on no system default zone default-zone permit system default zone distribute fullno system default zone mode enhancedWould you like to edit the configuration? (yes/no) n: nUse this configuration and save it? (yes/no) y: y # 100%User Access Verification37 login: adminPassword: XXXXXXXX请参考红色标记的输入选择，如与内相同，可直接回车。在命令行下使用ping测试网络是否通畅：mds9124# ping 54PING 54 (54) 56(84) bytes of data.64 bytes from 54: icmp_seq=1 ttl=64 time=36.7 ms64 bytes from 54: icmp_seq=2 ttl=64 time=1.84 ms64 bytes from 54: icmp_seq=3 ttl=64 time=35.9 ms64 bytes from 54: icmp_seq=4 ttl=64 time=1.60 ms64 bytes from 54: icmp_seq=5 ttl=64 time=11.2 ms- 54 ping statistics -5 packets transmitted, 5 received, 0% packet loss, time 4042msrtt min/avg/max/mdev = 1.608/17.473/36.738/15.790 ms光纤交换机初始配置完毕，请在管理服务器上安装管理软件，插入光盘“Cisco MDS 9000 Fabric Manager 4.X.X”，运行install_windows.htm。点击“Install Management Software”点击“Cisco Fabric Manager”：点击“Installing Fabric Manager”：如未安装JAVA，则先点击Jave Runtime Environment：点击“JRE 1.5 for Windows”安装JAVA。然后点击“FM Installer”（如果方框内为空，则需要允许ActiveX）：如出现如下提示：请点击信息栏，选择“允许阻止的内容”。重新点击“FM Installer”选择“是”选择“Custom”，点击“Next”：同意授权文件，点击“Next”：选择“Fabric Manager Server（licensed）”，点击“Next”：输入数据库密码，点击“Next”：输入FM密码，点击“Next”：选择“Local”，点击“Next”：点击“Install”：点击“Finish”，管理程序安装完毕。安装Cisco Device Manager，先输入http:/IP（光纤交换机IP地址）：点击“Cisco Device Manager”：点击“Next”：同意授权证书，点击“Next”：点击“Install”：点击“Finish”，结束安装。输入http:/IP（光纤交换机管理服务器IP）：输入用户名：admin，密码为安装Cisco Fabric Manager配置时设置的密码。点击右上角“Download”：点击“Fabric Manager”:输入用户名admin，及预先设置的密码，点击“Login”：输入光纤交换机IP及用户名密码，点击“Discover”：选择“No”:发现光纤交换机：点击“Open”，打开：Create Vsan：Adding Interfaces to VSANs：保存配置：点击“是”，确定修改：Click the Edit Local Full Zone Database icon选择相应的VSAN：添加Zoneset，右键点击“Zonesets”，选择“Insert”：配置Zoneset Name：添加Zone，右键点击“Zones”，选择“Insert”：配置Zone Name：右键点击Zone1，添加Zone成员：将光纤交换机端口分配给Zone：将Zone添加到Zoneset激活ZoneSet，右键点击“Zoneset-test”，选择“Activate”保存配置：附：光纤交换机参考配置如下：mds9124# sh runversion 4.1(3a)role name default-role description This is a system defined role and applies to all users. rule 5 permit show feature environment rule 4 permit show feature hardware rule 3 permit show feature module rule 2 permit show feature snmp rule 1 permit show feature systemusername admin password 5 $1$M/gW86t1$mkI60Q4cmKKU6kL02sSLQ. role network-adminip domain-lookupip host mds9124 37aaa group server radius radius snmp-server user admin network-admin auth md5 0xa88edff4448ccb003d7a108a4d5fab32 priv 0xa88edff4448ccb003d7a108a4d5fab32 localizedkeysnmp-server host 35 traps version 2c public udp-port 2162vsan database vsan 5 vsan database vsan 5 interface fc1/1 vsan 5 interface fc1/2 vsan 5 interface fc1/3 vsan 5 interface fc1/4ip default-gateway 54switchname mds9124line consoleboot kickstart bootflash:/m9100-s2ek9-kickstart-mz.4.1.3a.binboot system bootflash:/m9100-s2ek9-mz.4.1.3a.bin interface fc1/1interface fc1/2interface fc1/3interface fc1/4interface fc1/5interface fc1/6interface fc1/7interface fc1/8interface fc1/9interface fc1/10interface fc1/11interface fc1/12interface fc1/13interface fc1/14interface fc1/15interface fc1/16interface fc1/17interface fc1/18interface fc1/19interface fc1/20interface fc1/21interface fc1/22interface fc1/23interface fc1/24system default zone distribute fullzoneset distribute full vsan 5!Full Zone Database Section for vsan 5zone name Zone1 vsan 5 member interface fc1/1 swwn 20:00:00:0d:ec:ab:cf:80 member interface fc1/2 swwn 20:00:00:0d:ec:ab:cf:80 member interface fc1/3 swwn 20:00:00:0d:ec:ab:cf:80zone name Zone2 vsan 5 mem