富强鑫-FT60-3000.doc

项目 单位 FT-60 FT-90 FT-110 FT-140 射出单元 螺杆直径 mm 28 30 34 32 36 40 36 40 45 40 45 48 射胶压力 kg/cm 1857 1618 1260 2297 1815 1470 2204 1785 1410 2297 1815 1595 理论射出容量 cm 89 102 132 121 153 188 173 214 270 251 318 362 射出量 gram 82 93 119 109 138 171 157 193 245 227 288 327 ozs 2.9 3.3 4.2 3.8 4.8 6.0 5.5 6.8 8.6 8.0 10.1 11.5 射出率 cm/sec 60 70 89 64 81 100 83 102 129 97 122 139 熔胶量 kg/hr 37 42 54 43 55 68 46 57 72 46 58 66 螺杆转速 rpm 210 210 195 158 夹模单元 闭模力 metric tons 60 90 110 140 夹模行程 mm 270 300 350 380 循环时间 sec 1.8 1.8 1.8 1.8 模厚 mm 75-340 100-390 110-440 110-500 建议最小模具尺寸(HxV) mm 210x170 230x195 255x220 275x240 大柱内距(HxV) mm 320x260 350x300 390x340 420x370 模盘尺寸(HxV) mm 475x415 520x470 590x540 650x600 托模行程 mm 70 80 90 100 电气单元 电机马达 HP (kw) 10 (7.46) 15 (11.19) 15 (11.19) 20 (14.92) 温度控制器 (range) set (0-400C)x3 (0-400C)x3 (0-400C)x4 (0-400C)x4 电热容量 kw 3.9 5.1 6 8.4 其他 机械尺寸(LxWxH) mm 3900x1000x1700 4350x1050x1760 4800x1100x1800 5300x1250x1924 油箱容量 liter 135 190 230 260 机械重量 metric tons 2.8 3.5 4.2 5.0 最高系统压力 kg/cm 105 140 140 140 *射出量按聚苯乙烯比重1.05计算。*因产品不断研究改良，设计变更时，恕不另作通知。项目单位FT-180FT-220FT-260 射出单元螺杆直径mm48505557626862 6872射胶压力kg/cm2051189015621842155712941821 15141350理论射出容量cm3804124995366347637559081018射出量gram344373451485574690683821921ozs12.113.115.817.020.124.224.028.832.3射出率cm/sec130141170180213256240288323熔胶量kg/hr737995130154185185223250螺杆转速rpm143142144夹模单元闭模力metric tons180220260夹模行程mm420450520循环时间sec1.82.02.5模厚mm120-560200-650200-750建议最小模具尺寸(HxV)mm300x275340x300370x310 大柱内距(HxV)mm460x420520x460570x480模盘尺寸(HxV)mm725x685800x740870x780托模行程mm125145160电气单元电机马达HP (kw)25 (18.65)30 (22.38)40 (29.84)温度控制器(range) set(0-400C)x5(0-400C)x5(0-400C)x5电热容量kw10.314.217.4其他机械尺寸(LxWxH)mm5950x1300x22256200x1400x23006500x1500x2100油箱容量liter300420510机械重量metric tons6.48.810.6最高系统压力kg/cm140140140项目单位FT-320FT-420FT-520FT-600射出单元螺杆直径mm70758070758080858590射胶压力kg/cm1783155313651851165014501706151116801500理论射出容量cm1078123714071116128114571759198620102226射出量gram975111912731016116613381592179718202045ozs34.239.344.736414755606372射出率cm/sec297341388300345390389440446493熔胶量kg/hr266306348270310350242272275298螺杆转速rpm126138114130夹模单元闭模力metric tons320420520600夹模行程mm600670800900循环时间sec3.03.544.5模厚mm300-780250-800300-1000300-1100建议最小模具尺寸(HxV)mm420x360460x400525x525560x560大柱内距(HxV)mm650x550715x615810x810860x860模盘尺寸(HxV)mm980x8901075x9751200x12001250x1250托模行程mm190200220220电气单元电机马达HP (kw)50 (37.30)50 (37.30)60(44.8)75(56)温度控制器(range) set(0-400C)x5(0-400C)x5(0-400C)x6(0-400C)x6电热容量kw22.122.128.228.2其他机械尺寸(LxWxH)mm7200x1600x22007800x2000x22008500x2200x268010000x2200x2800油箱容量liter780100011001100机械重量metric tons13.117.52329.4最高系统压力kg/cm140140140140项目单位FT-1680FT-2000FT-2500FT-3000射出单元螺杆直径mm120130140150140150160170射胶压力kg/cm19151632170814881708148816711480理论射出容量cm85169995115851329911585132991868821097射出量(PS)gram78249043106441221810644122181659118731oz275320375430375430584659射出率cm/sec8621013117413481174134814211605熔胶量kg/hr6998399731117973111719282178螺杆转速rpm120110110100夹模单元闭模力metric tons1680200025003000夹模行程mm1600190019002200模厚mm500-1600600-1700600-1700600-1830建议最小模具尺寸(HxV)mm975x8451170x10401170-10401300-1170大柱内距(HxV)mm1600x13001800x16001800-16002000-1800模盘尺寸(HxV)mm2205x20052520x23202520-23202750-2550托模行程mm270300300330电气单元电机马达HP200225232.5 (173.4)257.5 (192)温度控制器(range) set(0-400C)x8(0-400C)x