Ultimate-乒乓球发射器搭建说明.docx

Makeblock Ultimate Robot Kits - Ball LauncherIntroductionThe Ball launcher is one of the Ultimate robot. You can control your robot with your smart device through a Bluetooth connection. And by adjusting the rotation of the motor launch a ball.For the installation steps, please do as follows. If you have any question about it, please post your trouble on the forum, I would give a replay.Now, lets startStep 1Materials list4*Threaded Shaft 4*393*D Shaft 4*502* Shaft Collar 4mm4*Shaft clamping hub 4mm2*Beam 0808-882*Beam 0824-1282*Timing pulley Slice 90T-New1*Motor Bracket 25V21*Motor Bracket 37V22*Plate D1*Bracket P31*Timing pulley 18T1*Gear m1*1630*Screw M4*827*Screw M4*142*Screw M4*164*Screw M4*221*Screw M4*353*Beam 0808-1842*Beam 0824-1442*Beam 0824-961*Beam 0824-802*Beam 0824-642*Base board plate V1.119*Hex nuts M4-N6*Screw M3*812*Hex Socket screw4*Plastic ring 4*7*25*Nylon M41*Gear m1*801*Timing pulley 90T1*Timing belt 123T 98mxl1*DC Motor 25mm V2.01*DC Motor 37mm V2.03*Bracket 3*311*Bracket 3*61*Rubber band1*Plate 7*9Electronic materials1*Makeblock Orion1*6P6C RJ11 cable 20cm1*Me Bluetooth Module V2.01*Battery Bracket6*AA Battery 1.5VStep 2Tools1.5mm Hexagonal Screwdriver3mm ScrewdriverSpannerStep 3Building the base:Materials:2*Beam 0824-1442*Beam 0824-1282*Beam 0824-961*Beam 0808-8810*Screw M4*144*Screw M4*224*Hex nuts M4-NProcedure：1. Install the Beam 0808-88 on Beam 0824-128.2. Assemble a rectangle by 2*Beam 0824-128, 2*Beam 0824-144 and 8*Screw M4*143. The Beam 0824-96 vertically mounted on the Beam 0824-144 with 4*Screw M4*22 and 4*Hex nuts M4-NStep 4Assembling transmission of DC motor 37mmMaterials:6*Screw M4*144*Screw M3*85*Hex Socket screw4*Hex nuts1*Beam 0808-881*Beam 0824-801*D Shaft 4*502*Shaft clamping hub 4mm2*Threaded Shaft 4*391*Timing pulley 90T2*Timing pulley Slice 90T-New1*DC Motor 37mm V2.01*Motor Bracket 37V21*Timing belt 123T 98mxl1*Timing pulley 18T1*Plastic ring 4*7*2Procedure：1. Install the two Timing pulley Slice 90T-New and a Shaft clamping hub 4mm on the Timing pulley 90T by using two Hex Socket screws, four Screws M4*14 and two Hex nuts.2. 2*Threaded Shaft 4*39 are installed on both ends of Beam 0808-88 and a Shaft clamping hub 4mm is installed in the middle of Beam 0808-88.3. Install 1 and 2 on the top of the hole by using a D shaft.4. Install Motor Bracket 37V2 and Timing pulley 18T on DC Motor 37mm V2.0 with 2*Threaded Shaft 4*39 and a Hex Socket screwStep 5Assembling transmission of DC motor 25mmMaterials:1*DC motor 25mmV21*Motor bracket 25V21*Shaft clamping hub 4mm1*D Shaft 4*504*Hex Socket screw2*Screw M3*81*Bracket 3*31* Shaft Collar 4mm1*Timing pulley 18T1*Timing pulley 90T4*Screw M4*14Procedure:1. Install the Motor bracket 25V2 on the DC motor 25mmV2 by using 2*Screw M3*82. Make the motor shaft through the third from the bottom up of the hole, and install Timing pulley 18T on the motor shaft.3. Install the Shaft clamping hub 4mm and Bracket 3*3 on both sides of Timing pulley 90T.4. Install 3 on the top of the hole by using D shaft, shaft collar and three Hex Socket screws.Step 6Make a launcherMaterials:2*Beam 0808-1842*Beam 0824-642*Plate D1*Bracket P32*Bracket 3*32*Threaded Shaft 4*3915*Screw M4*82*Screw M4*141*Screw M4*355*Hex nuts2*Plastic ring 4*7*21*Nylon M4Procedure:1. One of Plate D and Bracket P3 mounted on one end of the two Beam 0824-642. Put Beam 0808-184 through Plate D, then install Threaded Shat 4*39 on the first and the eighth holes of Beam 0808-184.3. Install Nylon M4 on Plate D with 2*Plastic ring 4*7*2, a Screw M4*8 and a Screw M4 *35. Then install Plate D on the other end of the two Beam 0824-64.4. Install 2*Bracket 3*3 on both sides of Beam 0824.5. Install Beam 0808-184 on the right of Bracket 3*3.Step 7Assembly of electronic modulesMaterials:6*Hex nuts12*Screw M4*84*Screw M4*144*Nylon M41*Makeblock Orion1*6P6C RJ11 cable 20cm1*Me Bluetooth Module V2.01*Battery Bracket6*AA Battery 1.5V2*Base board plate V1.1Procedure:1. Install Makeblock Orion on one of Base board plate V1.12. Install four Nylons on the Base board plate V1.1 by using four Screw M4*8.3. Install battery bracket on the other Base board plate V1.1.4. Install the Base board plate V1.1 on the Nylon M4.5. Install the Me Bluetooth Module V2.0 on the Beam 082496 of the base.Step 8Assembling everything up frontMaterials:1*plate 7*91*Bracket 3*61*Beam 0808-1846*Screw M4*142*Screw M4*164*Screw M4*88*Hex nuts M41*Plastic ring 4*7*21*D Shaft 4*503*Hex Socket screw1* Shaft Collar 4mm1*Shaft clamping hub 4mm1*Rubber bandProcedure:1. Install D Shaft 4*50 on Beam 0824-96 by using Shaft Collar 4mm and Shaft clamping hub 4mm2. Install Bracket3*6 on DC motor 37 mm, then install on the Shaft clamping hub.3. Install the Rubber band on Timing pulley 18T and Timing pulley 90T, then install Bracket 3*3 of the launcher4. Install the other Bracket 3*3 of the l