WOHA33_1052LNE 3C97_255_DEOA33-11-0001

Hong Kong Airlines Limited香港航空03110-01Hong Kong Airlines MEDHong Kong Airlines LimitedWO NO/工作指令号SEQ NO/序列号WOHA331052_255_97105297TitlePainting the marking of outside doorMcd&Rev/厂家工卡&修订日期标题A/C/飞机号/组别EO JC No./EO工卡EO JC Rev/工卡版本Workarea/工作区域Skill/工种Man Hour/工时BLNE/1DEOA33-11-0001R00机身PNT04:00Baseline/依据Operator EO/营运人EOEO Rev/EO版本Work Type/工作类别Threshold/首检Interval/重复检DWG F11212519,F11212538DEOA33-11-0001R00R00Written/编写Reviewed/审核Approved/批准2013-06-082013-06-082013-06-09Accomplished完工签署Complete Date完工日期Station维修站SHAREASON & DESCRIPTION/原因及描述Hong Kong airlines feedback outside door signs often damage or discoloration, issued the DEO to paint.TOOLS/工具TOOLS NECESSARY/必须工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注TOOLS IF NECESSARY/视情工具ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIAL/航材NOTE:OPERATOR MUST GET AND INSTALL THE PARTS THAT CORRESPOND TO THE RELATIVE WORKORDER NO.注释：请工作者严格按照工作指令号领取预定的航材装机PARTS AND MATERIAL NECESSARY/必须航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注PARTS AND MATERIALIF NECESSARY/视情航材ITEM项目P/N件号DESCRIPTION名称EQTP类型QTY数量APP适用性Conditions note互换信息及备注IMPORTANT NOTE:In the event of any discrepancies between the Chinese instruction and the English instruction, the English procedure should prevail.Record Additional Work/Findings(If Applicable) Reference No. Certificate of Release to Service (* Tick as appropriate # Different crews should perform the work on each of the systems)Certifies that the work specified, except as otherwise specified, was carried out in accordance with HKAR-145and in respect to that work, The aircraft / aircraft components are considered ready for Release to Service. HKA Approval No: AI / 135 / 706 * HNAT Approval No.: JMM 076, D3039 * HNAT Approval No.: JMM 047, D101115* HNAT Approval No.: JMM 049, D500023 * CASL Approval No: AI / 101 / 798 * TAECO Approval No.: DAI / 89 / 1295 * HAECO Approval No: DAI / 1 / 853 * SIAEC Approval No: AWI / 01 * STARCO Approval No.: JMM 039, D.200078 * SMECO Approval No: JMM 081, D.400009 * AMECO Approval No.: JMM001,D101131* Other: * Signature:_ Authorization No.:_ Date:_工卡Job card:DEOA33-11-0001TITLEPainting the marking of outside doorPerfInsp标题工作者检查者警 告：请遵守所参考手册的所有警告和注意事项，否则会造成人员伤害或设备损坏。WARNING: PLEASE OBEY ALL WARNING AND CAUTION OF REFERENCE MANUAL, OTHERWISE IT SHOULD CAUSE PERSONAL INJURE OR DAMAGE TO EQUIPMENTS.漆料/Top coating：色号 数量BAC7568 White 1BAC4876 Green 1BAC1247 Red 1耗材/Consumers：3M232-1 2EA3M232-2 2EA塑料布 1卷注1：漆料和耗材根据需要提前准备。NOTE 1: Finishes and consumable materials prepared in advance.注2：以下所喷门外部标识红字需符合香港AN第46条出口标记要求。NOTE 2: The red word on the outside marking must be in accordance with Hong Hong Air Navigation article 46 Exits Marking requirement.步骤/STEP：1. 参考图1拆下“各登机门、勤务门、应急门”外部所有标牌(含开门步骤标牌)，并清洁粘贴表面残留胶痕。Remove the all outside placards of entry and service doors and clean the surface.(contain the placard to open door step)2. 按照工作程序，执行喷漆前的准备工作。Do the set up job before painting according to the work procedure.3. 清洁喷漆区域飞机外表面。Clean the surface of the painting area.4. 参考SRM51-23-00及油漆厂家工艺说明，按附件图纸要求喷涂“登机门、勤务门及应急门”外部标识。Refer to SRM51-23-00 and the manufactory technic instruction, Painting the aircraft according to the requriement of the attached Figures.5. 清理喷漆区域，恢复飞机至可用状态。 Clean up the work area and get the aircraft back to its useable condition._FIG 1FIG 1-2:DWG NO F11212519 Door 4FIG 1-3:DWG NO F11212519 Doors 1 and 2FIG 1-4:DWG NO F11212519 Door 4FIG 1-5:DWG NO F11212519 Doors 1 and 2FIG