N6040安装配置手册

N6040 安装配置手册安装配置手册 一、初始化设置一、初始化设置 .1 二、命令行配置二、命令行配置 RAID.4 2.1 建立一个 RAID .4 2.2 修改时间.4 2.3 关闭集合快照.4 2.4 缩小根卷.4 2.5 添加LICENSE.4 2.6 配置双机.4 三、扩大三、扩大 RAID 集合，将其它盘加入阵列。集合，将其它盘加入阵列。.4 四、配置卷及四、配置卷及 ISCSI 主机映射主机映射.8 4.1 新键卷.8 4.2 配置 ISCSI-LUN.11 4.2.1创建LUN.11 4.2.2创建initiator group .12 4.2.3客户端安装initiator.13 4.2.4客户端连接N6040 .13 4.2.5 MAP LUN建立映射关系.13 五、主机识别硬盘五、主机识别硬盘 .15 硬件环境描述：n6040 双控制器，两个磁盘扩展柜，SATA 磁盘。A 和 B 控制器各需要在 FilterView 单独配置。其中硬盘加入和划分部分以举例说明 一、初始化设置一、初始化设置 A 控制器： Data ONTAP Release 7.1H2: Fri Nov 11 11:14:38 PST 2005 (IBM) System ID: (N6040b); partner ID: () System Serial Number: (N6040b) System Rev: A0 slot 0: System Board Processors: 2 Processor revision: B2 Processor type: 1250 Memory Size: 1022 MB slot 0: FC Host Adapter 0b 17 Disks: 6127.5GB 1 shelf with AT-FCX, 1 shelf with EFH slot 0: FC Host Adapter 0c slot 0: Dual SB1250-Gigabit Ethernet Controller e0a MAC Address: 00:a0:98:03:c1:12 (auto-unknown-down) e0b MAC Address: 00:a0:98:03:c1:13 (auto-unknown-cfg_down) slot 0: NetApp ATA/IDE Adapter 0a (0 x001f0) 0a.0 249MB Please enter the new hostname N6040b: Do you want to configure virtual network interfaces? n: y Number of virtual interfaces to configure? 0 1 Name of virtual interface #1 : vif（虚接口名称） Is vif a single s or multi m virtual interface? m s Number of links for vif? 0 2（虚接口数目） Name of link #1 for vif : e0a Name of link #2 for vif : e0b Please enter the IP address for Network Interface vif : . . . Please enter the netmask for Network Interface vif : Should virtual interface vif take over a partner virtual interface during failover? n: y The clustered failover software is not yet licensed. To enable network failover, you should run the license command for clustered failover. Please enter the partner virtual interface name to be taken over by vif : vif Please enter media type for vif 100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000) auto: Would you like to continue setup through the web interface? n: Please enter the name or IP address of the default gateway: The administration host is given root access to the filers /etc files for system administration. To allow /etc root access To all NFS clients enter RETURN below. Please enter the name or IP address of the administration host: What is the TimeZone: Asia/Shanghai Where is the filer located? : What language will be used for multi-protocol files (Type ? for list)?: language not set Do you want to run DNS resolver? n: Do you want to run NIS client? n: The initial aggregate currently contains 2 disks; you may add more disks to it later using the aggr add command. B 控制器 Data ONTAP Release 7.1H2: Fri Nov 11 11:14:38 PST 2005 (IBM) System ID: (N6040b); partner ID: () System Serial Number: (N6040b) System Rev: A0 slot 0: System Board Processors: 2 Processor revision: B2 Processor type: 1250 Memory Size: 1022 MB slot 0: FC Host Adapter 0b 17 Disks: 6127.5GB 1 shelf with AT-FCX, 1 shelf with EFH slot 0: FC Host Adapter 0c slot 0: Dual SB1250-Gigabit Ethernet Controller e0a MAC Address: 00:a0:98:03:c1:12 (auto-unknown-down) e0b MAC Address: 00:a0:98:03:c1:13 (auto-unknown-cfg_down) slot 0: NetApp ATA/IDE Adapter 0a (0 x001f0) 0a.0 249MB Please enter the new hostname N6040b: Do you want to configure virtual network interfaces? n: y Number of virtual interfaces to configure? 0 1 Name of virtual interface #1 : vif （虚接口名称） Is vif a single s or multi m virtual interface? m s Number of links for vif? 0 2（两个虚接口） Name of link #1 for vif : e0a Name of link #2 for vif : e0b Please enter the IP address for Network Interface vif :. . . (接口地址) Please enter the netmask for Network Interface vif : Should virtual interface vif take over a partner virtual interface during failover? n: y The clustered failover software is not yet licensed. To enable network failover, you should run the license command for clustered failover. Please enter the partner virtual interface name to be taken over by vif : vif Please enter media type for vif 100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000) auto: Would you like to continue setup through the web interface? n: Please enter the name or IP address of the default gateway: The administration host is given root access to the filers /etc files for system administration. To allow /etc root access To all NFS clients enter RETURN below. Please enter the name or IP address of the administration host: What is the TimeZone: Asia/Shanghai Where is the filer located? What language will be used for multi-protocol files (Type ? for list)?: language not set Do you want to run DNS resolver? n: Do you want to run NIS client? n: The initial aggregate currently contains 2 disks; you may add more disks to it later using the aggr add command. 二、命令行配置二、命令行配置 raid 2.1 建立一个建立一个 RAID N6040baggr options aggr0 raidtype raid4 N6040bdisk zero all spares 2.2 修改时间修改时间 N6040bdate 年月日小时分钟 2.3 关闭集合快照关闭集合快照 N6040bsnap reserve A aggr0 0 2.4 缩小根卷缩小根卷 N6040b vol size vol0 20G 确认完成加盘。 2.5 添加添加 license N6040blicense add XXXXXXX 可选步骤 2.6 配置双机配置双机 N6040bcf enable (需要重启后才生效) 三、扩大三、扩大 RAID 集合，将其它盘加入阵列。集合，将其它盘加入阵列。 登陆 WEB 管理 http:/* /na_admin/ 点击 FILERVIEW N6040bAggregatesManage 点击 aggr0Add disk 添加硬盘到阵列组 选择手动选择增加 添加硬盘，留出两块盘作为热备（SATA 做 DP 系统强制双热备） 四、配置卷及四、配置卷及 ISCSI 主机映射主机映射 4.1 新键卷新键卷 N6040bVolumesAdd 4.2 配置配置 ISCSI-LUN N6040bLunsEnable/Disable 4.2.1 创建创建 LUN N6040bLunsAdd 注意空间大小占用不要超过卷的 97% 4.2.2 创建创建 initiator group N6040bLunsInitiator Groups