未分配硬盘更换方案

6140坏盘更换后不回拷的手工操作方式2013-06-22 10:03:14|分类：storage|标签：copyback6140cam|举报|字号订阅6140有硬盘故障后，热备盘完成替换。有时候现场工程师去现场更换坏盘后，阵列没有进行热备盘回拷。VD的成员磁盘内有已经替换的热备盘，而故障盘槽位的新硬盘的状态为：Unassigned未分配。需要手工触发这个回拷动作，方式如下：方式一：使用服务顾问进行操作。服务顾问页面内左边选择 可移植虚拟磁盘管理 更换一个磁盘。右边出现两个选择下拉栏，上面是故障盘的位置，下面是可用的磁盘。两个下拉栏都选择故障盘的位置，点击确认，系统就会进行回拷操作了4.CAM内新硬盘的状态会从Unassigned未分配变为Replaced已替换。系统会逐个对VOLUME进行rebuild修复。方式二：使用命令行进行操作。/opt/SUNWsefms/bin/service -d 阵列名 -c 坏盘 -t -q 可用磁盘位service -d -c replace -t -q 两个硬盘的位置，同样都是使用这个盘。如：/opt/SUNWsefms/bin/service -d st6140c -c replace -t t85d02 -q t85d02Sun Storage Common Array Manager (CAM)Note: If you have the firmware level 6.xx.xx.xx on your array, no actions is needed after the drive replacement. The copy back operation will start, assuming that there are not more than two (2) operation in a combination of reconstruction or copy back taking place on the system. If so, it will be queued.Using the Browser User Interface (BUI):1. Select the array in CAM.2. Click on Service Advisor.3. Expand Portable Virtual Disk Management on the left pane.4. Select Replace a Disk Drive then follow the instructions.Using the Command Line (CLI):1. Use Sun Storage Common Array Manager (CAM) to confirm that reconstruction jobs are completed before moving forward to the next step.2. Use the following CAM command line to list the drives needing replacement:service -d -c replace -q listLocation of the service command:Solaris: /opt/SUNWsefms/bin/Linux: /opt/sun/cam/private/fms/bin/Windows: C:Program FilesSunCommon Array ManagerComponentfmsbinExample:/opt/SUNWsefms/bin/service -d st6140c -c replace -q listExecuting the replace command on st6140cDrives needing replacment:Tray.85.Drive.02In use hot spares:Tray.85.Drive.16Unassigned drives available for replacment:Tray.85.Drive.10Tray.85.Drive.05Tray.85.Drive.11Tray.85.Drive.06Tray.85.Drive.04Tray.85.Drive.03Tray.85.Drive.08Tray.85.Drive.12Tray.85.Drive.07Tray.85.Drive.09Tray.85.Drive.13Tray.85.Drive.14Tray.85.Drive.02The above example shows that the drive 85,02 needs to be replaced. This drive has already been replaced but the copy back did not start.3. Use the following CAM command line to manually trigger the copy back:service -d -c replace -t -q Example:/opt/SUNWsefms/bin/service -d st6140c -c replace -t t85d02 -q t85d02Executing the replace command on st6140cCompletion Status: SuccessIn the above example, we manually trigger the copy back by replacing the drive 85,02 wit