FPC1.0性能规格书

1、.TPG ELECTRONICS COMPANY LIMITED TPG 1.0 PITCH FPC CONNECTOR1. 适用范围 SCOPE 本规格书适用于FPC CONNECTOR 1.0系列 This specification covers the CONNECTOR 1.0series.2. 产品编号 ORDERING INFORMATION PART NO.: FZ C* - * EN 1 2 3 4 1.系列名称 Series nameFPC1.0 CONNECTOR2.组合样式 Assembly style C5 UPPER CONTACT 上接触C6 LOWER CONT

2、ACT 下接触3.接点数量 Number of contacts4-504.电镀方式 PlatingEN: LEAD FREEG: Gold over Nickel3. 外观尺寸 CONNECTOR DIMENSIONS 请参照图面. See attached drawings4. 材质 MATERIAL 绝缘胶体 Housing : NY-9T 耐燃等级(UL94V-0) Flammability rating (UL94V-0 ) 耐温265 导电端子 Contacts: 磷青铜 Phosphor Bronze5. 等级RATING 项目ITEM规格Standard额定电压Voltage

3、rating50V AC,DC额定电流Current rating0.5A AC,DC储存条件Storage conditions温度 Temperature 0 +28相对湿度 Relative humidity 40%60% 温度范围Temperature range-25 +85 (包含电流通过所产生的上升温度)-25 +85 (Including temperature rise in applying electrical current)TPG ELECTRONICS COMPANY LIMITED TPG 1.0 PITCH FPC CONNECTOR6. 1性能 PERFORM

4、ANCE项目ITEM测试条件TEST CONDITION规格PEQUIRMENT电气特性ELECTRICAL PERFORMANCE接触阻抗Contact Resistance将样品与适合之FPC连接,测试电压20mV,限电流10mA下进行阻抗测试.Mate applicable FPC and measure by dry circuit, 20mV Max, 10mA40m以下40mMax绝缘阻抗Insulation Resistance将样品与适合之FPC连接,提供相邻端子间测试电压500V DC进行绝缘阻抗测试.Mate applicable FPC and apply 500V DC

5、 between adjacent terminal or ground500M以上500MMin耐电压Withstanding voltage将样品与适合之FPC连接,相邻端子间可承受500V AC/1分钟.Mate applicable FPC , apply 500V AC/ 1minute between adjacent terminal or ground.目视外观无任何损坏异状No Breakdown机械特性MECHANICAL PERFORMANCEFPC保持力FPC Retention Force与FPC连接,以操作速度每分钟位移253mm进行FPC保持力测试.Insert

6、the connector , Pull the FPC at a rate of 253mm per minute0.05kgf/pin 以上0.05kgf/pin Min端子保持力Terminal Retention Force 端子与Housing 组装后,以操作速度每分钟位移253mm将端子拔出Housing,进行端子保持力测试Apply axial pull out force at the rate of 253mm per minute on the terminal assembled in the housing.0.25kgf/pin 以上0.25kgf/pin MinTP

7、G ELECTRONICS COMPANY LIMITED TPG 1.0 PITCH FPC CONNECTOR6.2 性能 PERFORMANCE项目ITEM测试条件TEST CONDITION规格PEQUIRMENT环境特性及其它性能ENVIRONMENTAL PERFORMANCE AND OTHERS耐热性Heat Resistance将样品与适合FPC连接,置于环境温度852测试时间96小时,再置放于室温下12小时.Mate applicable FPC and expose to 852 for 96 hour. Upon completion of the exposure p

8、eriod, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed.目视外观无任何损坏异状No Damage接触阻抗60m以下Contact Resistance 60m MAX耐寒性Cold Resistance将样品与适合FPC连接,置于环境温度-252测试时间96小时,再置放于室温下12小时.Mate applicable FPC and expose to

9、-252 for 96 hour. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed目视外观无任何损坏异状No Damage接触阻抗60m以下Contact Resistance 60m MAX冷热冲击Temperature Cycling将样品与适合之FPC连接,承受5 Cycle

10、s 冷热冲击后,置放于室温下下12小时.1 Cycle time如下a -252 30分钟b 852 30分钟Mate applicable FPC and subject to the following conditions for 5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall b

11、e performed.1 Cycle timea -252 30minutesb 852 30minutes目视外观无任何损坏异状No Damage接触阻抗60m以下Contact Resistance 60m MAXTPG ELECTRONICS COMPANY LIMITED TPG 1.0 PITCH FPC CONNECTOR6.3 性能 PERFORMANCE项目ITEM测试条件TEST CONDITION规格PEQUIRMENT盐水喷雾Salt Spray将样品与适合之FPC连接,使用51%浓度盐水,测试温度352,测试时间484小时后于室温下使用清水冲洗后再干燥.Mate ap

12、plicable FPC and expose to the following salt mist conditions. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified measurements shall be performed.Concentration : 51%Spray time : 484 hoursAmbient temperature: 352目

13、视外观无任何损坏异状No Damage接触阻抗60m以下Contact Resistance 60m MAX焊锡性Solderability锡温2455,将导电端子浸入锡炉面至Housing距离锡面1.0mm位置，焊锡时间30.5秒.Tip of solder tails and fitting nails into the moltenSolder (held at 2455 ) up to 1.0mm from thebottom of the housing for 30.5 seconds.润湿面积75%以上,并不得有漏焊针孔现象.75% of immersed area must show no voids ,pin holes.焊锡耐热性Resistance to Soldering Heat使用红外线回流焊请参考第7点When reflowing refer to par