高频振动器底坐安装（High frequency vibrator bottom seat installation）

1、高频振动器底坐安装（High frequency vibrator bottom seat installation）High frequency vibrator base mounting1, the fixed frame is better to use channel steel, so that vibration force can be increased. When welding channel steel, skip welding and prevent vibration cracking silo.2, thin rotten son to weld a reinf

2、orcement plate.3, whether the reinforcement plate or channel and vibration of the contact surface should be flat, or the screws will be tight, so that the vibration cylinder cylinder deformation, resulting in stop vibration.4, the installation of vibrators, with high flexibility of the gasket, in ca

3、se of loosening.5, the steel structure beam vibration aging, steel beam to add rubber pad, easy to produce resonance, so that welding residual stress relaxation, and dont rest on the node.High frequency vibrators are detected before use:After the high frequency vibrator is finished, the surface must

4、 be carefully cleaned so as to ensure good heat dissipation and keep it in the dry and ventilated place.Attention to high frequency vibrator and power control cabinetNotice of power control cabinet1, the shell must be reliable, grounding before use.2, the output electrical access to the device, whos

5、e first check the insulation, circuit and electric appliance is intact. The use of supporting special waterproof grounding, reliable before the power.3, the devices first boot, which is soft start, five or six seconds after full speed work. The boot button is started directly, and the current should

6、 be considered.4, the output frequency conversion, boot operation can change the frequency at any time, but not overload.Supporting the production of high frequency vibrator in order to ensure the performance and normal use.5, use should pay attention to ventilation, prevent high temperature (sun) a

7、nd water drench.The use, maintenance, maintenance and repair of high frequency vibrator1, the high frequency vibrator before use should check the insulation, with 500 volt megohm table of motor winding and Insulation check, the value shall not be less than 2 ohm, or its main 120 degrees with constan

8、t temperature drying box.2, the high frequency vibrator parts are fixed in place, the screws are loose, check, confirm the error, you can test machine. When testing the machine, the vibrator must be on the soft object (sponge, etc.) and must not be placed directly on the concrete floor.3 、 the high

9、frequency vibrator motor shaft can only be installed in horizontal direction, on the template must not allow a certain angle with the level.4. The high frequency vibrator wire is connected with the cable and is fixed on the handle of the motor, so as to avoid pulling the motor lead off when the moto

10、r is vibrating and pulling the cable, thereby causing the lack of phase and burning the motor.5, in the operation found that screws loose, should promptly stop vibration and power cut, to prevent vibration wounding.6, high frequency vibrator to damp, strictly prohibit water, such as water after dryi

11、ng must be used again.7, should be normal inspection of power lines, sockets, plug switches, wiring is loose, safe, ensure good contact safety.8, after the vibrator is used, the appearance must be carefully cleaned, to ensure good heat dissipation, and placed in a dry ventilated place, so that the n

12、ext use.Direct manufacturers T beam and box girder, trolley tunnel, dam and other large aqueduct track board, cement component special attachment type high frequency vibrator and auxiliary control cabinet:/ / QQ:1372761599 (space with data and video

13、)Debugging video of high frequency vibrator before leaving factory:Http://v_show/id_XMzU0MTE5ODE2.htmlHigh frequency vibrator site warehouse site commissioning video:Http://v_show/id_XNDA3ODU5NTAw.htmlHigh frequency vibrator installation video:Http://v_show/id_XMzU0M

14、Dk4NTcy.htmlHigh frequency vibrator installation video 02:Http://v_show/id_XMzU0MDk3MDg0.htmlHigh frequency vibrator; tunnel trolley; application video:Http://v_show/id_XMzYzMjQyNjg4.htmlApplication of South to North Water Diversion project:Http://v_show/id_XMzY0NzU0

15、NDE2.htmlMore high frequency vibrator video, please:Http://u/UNDEwMDI4MDM2/videosMore high frequency vibrator video, please:Http://u/UNDEwMDI4MDM2/videosThe benefits of using high frequency vibratorsSpecial high frequency vibrator for bridge prefabrication is portable and high

16、in amplitude. The high frequency vibrator is more suitable for prestressed concrete T beam. The previous construction has been using a common external vibrator, ordinary type vibrator in 2.0kw vibrator while in precast beam can meet the requirements, but the quality of its major, four screws, so the

17、 installation and disassembly is difficult, time-consuming and laborious. The damage frequency of the vibrator is relatively high, so it is easy to find the phenomenon of vibration leakage if it is not found, repaired or replaced in time. As the ordinary vibrator is not convenient to move, the numbe

18、r of one-time purchases is much larger than the fast type, so the cost is also increased. Ordinary type vibrator for low frequency vibration, damage to the template is relatively large, which not only increases the weight of the template but also increases the cost, but also 1.5KW vibrator beneath t

19、he beam flange is thick and there is insufficient implicit vibration force. Therefore, it is necessary to select the vibration parameters and structural dimensions of the vibrator reasonably according to the shape of the beam, the nature of the concrete and the construction conditions, so as to achi

20、eve the desired vibration effect.Notes on the use of attached high frequency vibrators and matching control cabinetsNotice of power control cabinet1, the shell must be reliable, grounding before use.2, the output electrical access to the device, whose first check the insulation, circuit and electric

21、 appliance is intact. The use of supporting special waterproof grounding, reliable before the power.3, the devices first boot, which is soft start, five or six seconds after full speed work. The boot button is started directly, and the current should be considered.4, the output frequency conversion,

22、 boot operation can change the frequency at any time, but not overload.Supporting the production of high frequency vibrator in order to ensure the performance and normal use.5, use should pay attention to ventilation, prevent high temperature (sun) and water drench.The use, maintenance, maintenance

23、and repair of high frequency vibrator1, the high frequency vibrator before use should check the insulation, with 500 volt megohm table of motor winding and Insulation check, the value shall not be less than 2 ohm, or its main 120 degrees with constant temperature drying box.2, the high frequency vib

24、rator parts are fixed in place, the screws are loose, check, confirm the error, you can test machine. When testing the machine, the vibrator must be on the soft object (sponge, etc.) and must not be placed directly on the concrete floor.3 、 the high frequency vibrator motor shaft can only be install

25、ed in horizontal direction, on the template must not allow a certain angle with the level.4. The high frequency vibrator wire is connected with the cable and is fixed on the handle of the motor, so as to avoid pulling the motor lead off when the motor is vibrating and pulling the cable, thereby caus

26、ing the lack of phase and burning the motor.5, in the operation found that screws loose, should promptly stop vibration and power cut, to prevent vibration wounding.6, high frequency vibrator to damp, strictly prohibit water, such as water after drying must be used again.7, should be normal inspecti

27、on of power lines, sockets, plug switches, wiring is loose, safe, ensure good contact safety.8, after the vibrator is used, the appearance must be carefully cleaned, to ensure good heat dissipation, and placed in a dry ventilated place, so that the next use.Notes on the use of high frequency vibrato

28、rsNotes on the use of high frequency vibrators1. before use should check the insulation, with 500 volt megohm table of motor winding and Insulation check, the value shall not be less than 2 ohm, or its main 120 degrees with constant temperature drying box.2, the motor parts are fixed in place, screw

29、s are loose, check, confirm the error before you can test machine. When testing machines, vibrators must be placed on soft objects (sponges, etc.) and must not be allowed to be tested on cement grounds.3, the vibrator motor shaft can only be installed in horizontal direction, on the template must no

30、t allow a certain angle with the level.4, vibration motor lead wire and cable connection, fixed on the handle of the motor, so as to avoid the motor vibration and drag cable lead motor lead broken, resulting in lack of phase,Burn out motor.5, in the operation found that the screw loose should be in

31、time, finally tight, to prevent the motor into moistureproof.6, should be normal inspection of power lines, sockets, plugs, switches, wiring is firm and safe, ensure good contact.High frequency vibrator base mountingThe benefits of high frequency vibrators in combination with the control cabinetDo y

32、ou know the benefits of using a high frequency vibrator in combination with a control cabinet? It is mainly used in the prefabrication of large concrete components, and can work in harsh conditions. It is reliable, energy-saving, light weight, easy to operate and so on. The companys products cost-effective