CASE凯斯挖掘机：防盗

1、1,ANTI-THEFT SYSTEM,B/G 621,V/G 469,To activate anti-theft system, wires V/G 469 & B/G 621 must be connected together. These wires are located behind the radio near the four relays. Machines shipping from the factory will not have these wires connected,2,ANTI-THEFT SYSTEMcontinued,0,0,0,PASSWORD,AS

2、SHOWN IN MONITOR,After connecting anti-theft wires, the system can now be activated. After turning on the key switch, the above will be displayed in the monitor. A security code must be entered using the following procedure,0,3,ANTI-THEFT SYSTEMcontinued,0,0,0,PASSWORD,AS SHOWN IN MONITOR,Push the t

3、ravel mode switch and select the first digit of the security code. By pushing the travel mode switch you will scroll through 0 9. When the number has been selected push the work mode switch to select the next number in the security code,0,1,4,ANTI-THEFT SYSTEMcontinued,1,0,0,PASSWORD,AS SHOWN IN MON

4、ITOR,Push the travel mode switch and select the second digit of the security code. By pushing the travel mode switch you will scroll through 0 9. When the number has been selected push the work mode switch to select the next number in the security code,0,2,5,ANTI-THEFT SYSTEMcontinued,1,2,0,PASSWORD

5、,AS SHOWN IN MONITOR,Push the travel mode switch and select the third digit of the security code. By pushing the travel mode switch you will scroll through 0 9. When the number has been selected push the work mode switch to select the next number in the security code,0,3,6,ANTI-THEFT SYSTEMcontinued

6、,1,2,3,PASSWORD,AS SHOWN IN MONITOR,Push the travel mode switch and select the fourth digit of the security code. By pushing the travel mode switch you will scroll through 0 9. After selecting the fourth digit, push the auto-mode switch. The alarm will sound indicating the password has been accepted

7、. Turn the ignition key switch off,0,4,7,ANTI-THEFT SYSTEMcontinued,After setting the password, the anti-theft system will only work if the following procedure is completed: After work is completed for the day and just before exiting the cab after the ignition switch is turned off. Turn ignition swi

8、tch “off and on” two times in two seconds. When this is completed the alarm will sound and system is activated,8,ANTI-THEFT SYSTEMcontinued,0,0,0,0,PASSWORD,AS SHOWN IN MONITOR,After the anti-theft system is activated: After turning on the key switch the above display will be in the monitor,9,ANTI-T

9、HEFT SYSTEMcontinued,0,0,0,PASSWORD,AS SHOWN IN MONITOR,Push the travel mode switch and enter the first digit of the security code. Push the working mode switch and select the second digit,0,1,10,ANTI-THEFT SYSTEMcontinued,1,0,0,0,PASSWORD,AS SHOWN IN MONITOR,Push the travel mode switch and enter th

10、e second digit of the security code. Push the working mode switch and select the third digit,2,11,ANTI-THEFT SYSTEMcontinued,1,2,0,0,PASSWORD,AS SHOWN IN MONITOR,Push the travel mode switch and enter the third digit of the security code. Push the working mode switch and select the fourth digit,3,12,

11、ANTI-THEFT SYSTEMcontinued,1,2,3,0,PASSWORD,AS SHOWN IN MONITOR,Push the travel mode switch and enter the fourth digit of the security code, then push the auto mode switch. If the correct security code was entered the monitor will automatically scroll to the normal display screen. Start engine,4,13,

12、ANTI-THEFT SYSTEMcontinued,1,2,3,5,PASSWORD,AS SHOWN IN MONITOR,If the wrong security code is entered the above screen is displayed “ERROR”. If the security code is not known or forgotten, turn key switch off and disconnect wires V/G 469 & B/G 621. With these wires disconnected the anti-theft system will be deactivated. To change the security code, reconnect these wires, turn key on and select new security code using pervious procedure,ERROR,14,ANTI-THEFT SYSTEM,ANTI-THEFT SYSTEM ACTIVATED & ALARMED Trav