汽车倒泊防撞报警器的设计

1、编号xx大学xx学院毕业设计（论文）相关资料题目： 汽车倒泊防撞报警器的设计 系 专业学 号： 学生姓名： 指导教师： （职称： ） （职称： ）xxxx年x月xx日目 录一、毕业设计（论文）开题报告二、毕业设计（论文）外文资料翻译及原文三、学生“毕业论文（论文）计划、进度、检查及落实表”四、实习鉴定表xx大学xx学院毕业设计（论文）开题报告题目： 汽车倒泊防撞报警器的设计 系 专业学 号： 学生姓名： 指导教师： （职称： ） （职称： ）xxxx年x月xx日 课题来源由于随着科学技术和汽车工业的发展，许许多多的汽车安全装置也得到大力的发展。汽车上面安装防撞警报器能够极大的方便司机的驾驶，保

2、障司机的安全，并且能在紧急情况下能自动刹车防止汽车之间的相撞。随着人们安全意识的提高，在汽车上安装防撞倒泊警报器将必不可少。科学依据（包括课题的科学意义；国内外研究概况、水平和发展趋势；应用前景等）在当今社会，知识的实用性越来越得到重视。如何从海量的知识群中找出有用的知识并付诸实践，这是很值得摸索的。单片机的应用日益普及，汽车的数量急剧增加，保障汽车驾驶人员的安全也变得越来越重要了。目前在汽车警报器经过20多年的发展 ，已经历了从开始的由单片机的蜂鸣器到由频率控制声音的急促报警到进一步的可视的智能化防撞报警系统。汽车防撞装置主要是通过车与障碍物之间的距离，车速信号的发射与接收由信号控制系统既是

3、利用单片机来控制车速。并发出不同频率的报警信号。当车速与车距距离进入比较危险的状态时，单片机自动控制发出紧急制动信号刹车，以此来达到防撞的目的。由上述可知，汽车与障碍物的距离只有在危险距离状态才有发生碰撞的可能，汽车防撞装置系统的设计任务主要是采集汽车与障碍物的距离和本车车速，并与当时车速下安全警报距离与危险距离之间进行比较，判断汽车与障碍物的距离是否安全。当达到的安全警报距离时能发出声音报警。研究内容在倒车时不断测量汽车尾部与其后面障碍物的距离，并实时显示其与障碍物之间的距离，在不同的距离范围内发出不同的报警信号，并且提高报警系统的稳定性，以提高汽车倒车时的安全性。本文设计了一种超声波汽车倒

4、泊防撞报警器，本报警器具有以下功能：最大测距4.9m，最小测距0.1m，实时显示测得的距离；在不同的时间利用三个不同的超声波传感器进行测距，能够有效的提高报警的稳定性。在不同的危险距离范围内发出不同的频率报警信号，驾驶员还可以根据个人需要调整设置报警距离。利用555来控制蜂鸣器的发声频率，直接运用单片机的i/o口控制报警器的工作。能够大大降低软件的复杂程度。该报警器与其它报警器相比具有功能多、硬件电路简单、工作稳定可靠等优点。拟采取的研究方法、技术路线、实验方案及可行性分析研究方法：理论联系实际。技术路线：理论联系实际。实验方案：对比“基于at89c51单片机的超声波防撞报警系统”跟“基于at

5、89c2051单片机的超声波防撞报警系统”，前者性价比更高，所以选择前者。可行性分析：能够理论联系实际解决实际性的问题。此方案可行。研究计划及预期成果初步讨论基于at89c51单片机来实现汽车倒泊防撞警报器的设计，分析了运用at89c51和at89c2051作为主控制器的两种方案。重点介绍了at89c51来实现的方案。对控制器，超声波发射电路，超声波接收电路，高低频报警电路，led显示电路等模块，以及运用单片机的i/o口如何具体的控制作了一定的说明。第四部分中，介绍系统的硬件框图、软件流程图、中断子程序流图等，给出了具体的软件实现的方案。利用51 系列单片机设计的测距仪便于操作、读数直观。测距

6、仪工作稳定, 能满足一般近距离测距的要求, 且成本较低、有良好的性价比。特色或创新之处考虑非常周全，不但提供了相应的理论基础知识，一定的电子电路图，还为详细的设计过程截取图片已具备的条件和尚需解决的问题对于at89c51单片机来实现汽车的倒泊防撞警报器尚取得了一定进展，但是还是有很多的不足之处：（1）应该引入更加完善的显示系统，是司机能更加清楚的了解倒车时的情况。（2）引入先进的语音模块，通过人性化的语音报警信号。（3）在紧急情况，应该自动使汽车紧急刹车，防止汽车与障碍物之间相撞。（4）应该对该警报器进行实际的测量，适当的进行调节，最大限度的减少误差。但是未来利用单片机来实现汽车的倒泊防撞警报

7、器仍然有广阔的前景，随着单片机的功能日渐增强，能够使报警更加人性化指导教师意见 指导教师签名：年 月 日教研室（学科组、研究所）意见 教研室主任签名： 年 月 日系意见 主管领导签名： 年 月 日外文原文microelectronic engineeringsouth koreabschool of information and communication engineering, college of engineering, inha university, incheon 402-751, south korea cdepartment of electrical engineerin

8、g, college of engineering, choongang university,seoul 156-756, south korea.available online 17 february 2006. abstractwe report on the fabrication of a polymer-based 2.5gbps4 channel optical interconnecting micro-module for optical printed circuit board (o-pcb) application. an optical waveguide arra

9、y is used for optical transmission from vertical surface emitting laser (vcsel) array to photodiode (pd) array and the built-in 45 waveguide mirrors are used for vertical coupling. the optical waveguide array and the 45 mirrors are fabricated by uv imprint process in one-step. we fabricate microlens

10、ed vcsels by micro-inkjetting method, which reduced radiation angle of vcsel from 18 to 15 for better light coupling. we use solder ball array and pin array for alignment between o-pcb and the electrical sub-boards with alignment mismatch below 10m in x, y and z axis. the fabricated optical intercon

11、nection module transmits data at the rate of 2.5gbps per channel.keywords: optical interconnection; photonic integrated circuit; micro-fabrication; uv embossingarticle outline1. introduction 2. fabrication of waveguide array and 45 mirrors 3. microlensed vcsel 4. passive alignment 5. optical interco

12、nnect modules 6. conclusion acknowledgements references1. introductionin the progresses of microprocessor and the input-output (io) devices, the need for higher bandwidth is rapidly growing. high speed interconnects are demanding next generation io interconnects of highly increased data capacity bec

13、ause todays io interconnects are suffering bottleneck in bandwidth at the io interface. many attempts to increase the io interconnect bandwidth have emerged 1. these attempts to extend electrical interconnect in more bandwidth manner are hard to solve fundamental problems facing the limitation of el

14、ectrical properties over gigabits per channel data capacity.operation of electrical interconnect schemes in gigabit regime will meet bottlenecks related to the properties of electrical interconnects, including material properties, skew, jitter, emi, and power consumption. to improve the performances

15、 of electrical interconnects, many efforts in signal processing techniques such as pre-emphasis, equalization, multilevel signaling, and coding, deterministic jitter are needed to keep the trace of the bandwidth progress 2, 3 and 4.optical interconnection has a potential as an alternative approach t

16、o solve these problems because optical interconnection has many advantages over electrical interconnection such as high frequency, high bandwidth, light, immunity to emi, low skew, low jitter, no need of ground line, easy for impedance matching.to realize an optical interconnection module for o-pcb

17、application, various photonic devices like light sources, detector arrays, and waveguide arrays are needed. the waveguides are interconnected to light sources and photo-detectors in a multiple array. the 45 waveguide mirrors are used for interconnecting vcsel arraywaveguide array/waveguide arraypd a

18、rray. once the o-pcb is designed and fabricated it has to be put together with the existing electrical circuits such as driving circuits for micro-lasers and micro-detectors. hence, we need micro-fabrication techniques for realizing optical interconnection module.we carried out micro-fabrication for

19、 optical interconnection module, which include design and fabrication of waveguides, coupling schemes and passive alignment. for this, we focus on the following issues: one is the concurrent fabrication of a waveguide array and 45 mirrors in one-step in order to reduce the number of processing steps

20、 for low-cost production and another is a method to improve coupling efficiency between vcsel arraywaveguide array/waveguide arraypd array including the passive alignment method between the different parts of the optical interconnection module. this paper demonstrates a micro-fabrication of optical

21、interconnection module to be used for the realization of optical printed circuit board (o-pcb) 7 and 8.2. fabrication of waveguide array and 45 mirrorsto use polymers as materials of the waveguide, embossing technique is used because of its relatively easy fabrication process. we fabricated polymer

22、waveguides by uv embossing, which also involves fabrication of mold and replica. uv curable polymers are used as materials of waveguides and silicon mold is used to form waveguide patterns. for vertical coupling between vcsel array and waveguide array and between the waveguide array and the pd array

23、, we have to utilize mirror face at each end of the waveguide. to achieve this process, waveguide mold equipped with 45 faces at each end of the mold is needed to form the vertical coupling structure in a single fabrication step. we made a 12 channel silicon waveguides mold, which has 45 mirror face

24、 at the ends of each waveguide. the dimension of the waveguide is 50m width and 50m height and the waveguide layout pitch is 250m and the length is 7cm. with this mold, we performed uv embossing to make embedded type waveguides.to fabricate a 12 channel silicon waveguides mold, we etched silicon sub

25、strate with koh-saturated isopropanol solutions in two steps: first is to make a vertical coupling path for the waveguides and the other is to make 45 slope for the fabrication of mirror faces. first, a metallic mask is patterned on the silicon substrate and the silicon is vertically etched with koh

26、 to form a waveguide pattern. in the next step to form 45 slope, a thin film of sio2 is grown on patterned waveguide. and photoresist is patterned at the end of the each waveguide structure and the ends of the waveguides are etched with koh-saturated isopropanol solution to form 45 slope. after the

27、sio2 is stripped, the process of fabricating silicon mold equipped with 45 mirror is completed.we fabricated 12 channel embedded waveguide array by uv embossing using the prefabricated silicon mold. waveguide fabrication process is shown in fig. 1. uv curable polymer, which is used as cladding layer

28、 with index as 1.45 at 850nm wavelength, is dropped in the hollow cavity of a transparent substrate such as pdms template. after silicon mold is pressed on template the uv light is irradiated. silicon mold is detached and metallic film is coated on the 45 slope at the end of the waveguide to enhance

29、 coupling efficiency. and then the core polymer is dropped and a flat substrate is covered and pressed onto the core material which is also uv curable polymer with refractive index of 1.47 at 850nm wavelength. the uv light is irradiated once again. after the upper and lower templates are detached, w

30、e can get a complete array of polymer waveguides with built-in 45 mirror face at each end of the waveguide.view within article3. microlensed vcselone of the approaches to collimate the light from vcsel arrays to the waveguide is the use of microlenses 9 and 10. this method offers an increase in coup

31、ling efficiency and alignment tolerance. the volume of a polymer drop to fabricate these lenses is approximately a few tens of picoliters. we are able to control the size of the microlenses by controlling the amount of the polymer drops and by controlling the viscosity of the materials. uv curable p

32、olymer is used for inkjetting, of which the viscosity and the refractive index are 300cps and 1.51 at 850nm wavelength. shows one of the microlensed vcsel array and microlensed vcsel has a microlens formed by the inkjetting method on the aperture of vcsel. inkjetting of uv curable resin on the vcsel

33、, lens material is aligned automatically on the aperture of vcsel. shows a view of the system where the output power from the microlensed vcsel arrays is measured for their divergence. the divergence angle of the laser light from the vcsel is shown to become narrower by using microlenses by the coll

34、imating effect pf the light from vcsel. because of the microlens, the higher order modes from the vcsel are suppressed by the cavity effect 10. the emitted output from the vcsel cavity is reflected back by microlens layer and is focused on the vcsel cavity. during this process, the divergence angle

35、of the vcsel is reduced. in this case, the divergence angle of the vcsel decreased from 18 to 15 after forming microlens. we conducted simulation study about the coupling efficiency between vcsel and the waveguide by using the ray tracing method. as the divergence angle of the vcsel was put into the

36、 calculation, the coupling efficiency of the vcsel with microlens was found to be 0.44db is 0.96db which were better than that of vcsel without microlens as 1.40db. here dimension of waveguide is 50m width, 50m height and 7cm length. refractive indices of the core and the cladding are 1.47 and 1.45,

37、 respectively, at 850nm wavelength. the distance between the vcsel and the waveguide is 100m.view within article4. passive alignmentsolder ball array and pin array are placed on the electrical sub-boards to bond the o-pcb and the electrical sub-boards with high precision. for precision alignment, so

38、lder ball array in diameter of 450m are used to thermally attach to the chip module. the solder ball array can be used for vertically alignment between the main o-pcb and the sub-boards within a mismatch below 10m. the size of the solder ball is 500m on average with standard error of 5m.two types of

39、 pin arrays are used. one array with diameter of 1mm is for alignment and the other with diameter of 200m is for electrical interconnection. the 1mm pin array is used for lateral alignment between the main o-pcb and the sub-boards. because of the impedance match, the pin array of the electrical inte

40、rconnection is limited. similar to solder ball array alignment tolerance of the pin array, about 10m, depends on variation of diameter of pin. the size of the pin is 1mm on average with standard error of 10m.we conducted simulation study about the coupling efficiency between the vcsel-waveguide pair

41、 and the waveguide-pd pair by ray tracing. with the variation of misalignment of x, y, and z axis we calculated the coupling efficiencies. from the calculation we obtained the total coupling loss within 2.30db for the worst case of having position errors as large as 10m in the xz axis and in the y a

42、xis, respectively. for example, when the position misalignment is 10m in the xz axis and in the y axis, the coupling loss between vcsel-waveguide is 1.59db and the coupling loss between vcsel-waveguide is 0.71db. from the previous results, one can achieve the alignment between solder ball array and

43、pin array can be achieved for alignment between main o-pcb and sub-boards with precision as about 10m in xz axis and in y axis, respectively. here the dimension of the waveguide is 50m width and 50m height. the refractive indices of the core and the cladding are 1.47 and 1.45, respectively, at 850nm

44、 wavelength. the distance between the vcsel and the waveguide is 100m in the y axis.view within article5. optical interconnect moduleswe demonstrated the use of optical interconnection module for the assembly of o-pcb having four 2.5gbps channels. the optical interconnection module, which includes e

45、/o (electrical/optical) conversion unit, is attached to the o-pcb with solder ball. the solder ball bonding is designed to accomplish the alignment between the waveguide structure and the electric circuit with high precision. the o-pcb prototype consists of main body of o-pcb and two electrical sub-

46、boards. the main o-pcb has embedded waveguide which is the medium of optical interconnection. the two sub-boards are used for electrical-to-optical (e/o) or optical-to-electrical (o/e) conversion. the vcsel array and the pd array are bonded to interconnect the waveguide to the bottom of the sub-boar

47、d. the driving circuits are placed on the opposite side to vcsel array and pd array. the power, ground and other electrical control signal are supplied through the pin grid. the main o-pcb is placed on the e-pcb within a rectangular area of 70mm10mm at the center of the e-pcb.the overall planar size

48、 of the o-pcb is 200mm80mm and thickness is 1mm. the uv embossed waveguide including the 45 mirror for vertical coupling is inserted into the e-pcb and is glues with uv-epoxy. the sub-boards including vcsel array/pd array are designed and fabricated using conventional analysis of microstrip line.vie

49、w within articlewe finally evaluated the quality of the optical interconnection module. first, we tested the waveguide array with 45 mirror face. the total losses of the waveguide include the propagation loss, the coupling loss, the 45 mirror loss and the insertion loss. and an average total loss is

50、 7.9db for a waveguide of 7cm length and their variation is within 1db. for the worst case, in 12 channel, the total loss was 8.9db.to demonstrate the data transmission performance, we utilized aligned optical interconnection module .a 2.5gbps psudo-random binary system (prbs) pattern were put in to

51、 the vcsel driver via the pin grid and the electrical output signal of the module were connected to a wide-band oscilloscope. an eye pattern of 2.5gbps transmission was clearly observed without any significant distortion.view within article6. conclusionwe performed micro-fabrication for optical inte

52、rconnection module. the optical waveguide array is fabricated by uv imprint process. the 45 mirrors faces are fabricated as an integrated part of the silicon waveguide mold for low-cost one-step processing. we fabricated microlensed vcsels by micro-inkjetting method and found a significant increase

53、in the improvement of the coupling efficiency reaching 0.96db. use of solder ball array and pin array for the alignment between the o-pcb and the sub-boards could be achieved with a precision below 10m in the xy axis and in the z axis. this passive alignment is designed for coupling loss induced by

54、of misalignment within 2.3db in total. we designed and fabricated a 2.5gbps4 channels optical interconnecting micro-module for optical printed circuit board (o-pcb) application. this optical interconnection module transmits data at the rate of 2.5gbps per channel.this work has been supported by the

55、engineering research center grant no. r11-2003-022 for opera (optics and photonics elite research academy).中文译文运用于o-pcb的2.5gbps x4通道的光学微模型装置光学和光子精英研究院（opera），仁川的仁荷大学是402-751，韩国学校信息与通讯工程，工程学院，仁荷大学，仁川402-751韩国中央大学电气工程系，首尔是156-756，韩国在2006年2月17日可以在线。摘要 我们报告的聚合物制造的2.5gbps的 4通道光学互连微型光学印刷电路板模块（o型pcb）的应用程序，

56、光波导阵列用于从垂直表面的光传输发射激光器（vcsel）的光电二极管（pd）的阵列和内置的45 波导镜使用垂直耦合。光波导阵列和45 镜紫外压印是工艺制造的一步，。我们通过微连接方法制造的微型vcsel方法，vcsel的角度从辐射18 减少到辐射15 是为了更好的光耦合。我们使用焊球阵列和针在o印刷电路板上并且电气板对齐低于10微米的x，y，z轴配板。虚构的光互连传输模块在2.5gbps速率下每通道的数据。关键词：光互连;光子集成电路，微加工，紫外压印大纲1、导言2、波导阵列的制备和45 镜3、显微镜的vcsel 4、被动对准5、光互连模块6、结论相关内容1.导言在随着微处理器和输入输出（i/o）的设备进步，对高带宽的需求也迅速增长。高速互连所要求的新一代高的io数据容量增加互连，因为今天的io互连遭受带宽瓶颈的是在io接口。许多人试图增加互连带宽的io出现在1。这些尝试扩大更多的电气互连带宽的方式是难以解决的根本问题是对所面临的每通道的数据的能力吉电性能的限制。 电气互连千兆制度计划的实行将满足相关的电互连特性瓶颈，包括物质的性质，歪斜，抖动，emi和电消耗。为了提高电互连的特性，有许多在信号处理技术上的努力，如预加重，均衡，