巴可DP2K系列故障代码

1、BARCO DP2K 系列故障代码译表本文将列举绝大部分会显示在巴可 DP2K系列放映机触摸屏与日志中的故障 错误代码并译文备查， 同时将针对部分常见的对我放映工作有价值的故障提供解 决方法。需要注意的是，某些代码会同时表示错误和警告， 某些表示错误(error )， 某些是警告( waring )。在“警告”状态下，放映机虽将继续维持运转，但仍建 议尽快解决导致“警报”的故障，否则， “警报”状态将有可能引发“错误”的 产生，而最终导致停机事故的发生。故障代码列表如下，可用 ctrl+f 快捷键进行搜索：5003: “ light sensor - no communication” (Er

2、ror)“灯传感器 - 无通讯”5004: “ lamp - no communication ” (Error)“灯 - 无通讯”状态解决方法灯箱没有被正确安装检查灯箱安装，并重置灯箱使用了与本机型号不匹配的灯箱选择匹配灯箱同时显示代码 5180(lamp house - not connected )见 5180与灯箱无通讯检查灯箱前端蓝色插头是否损坏5005: “ lamp power supplies - communication failed” (Error)灯电源 - 通讯失败”状态解决方法CTRL in, CTRL out 线没有插紧重新连接电源模块上的 CTRL接口与接 线A

3、ddress 线没有插紧重新连接 address 线主电源输入线没有插紧重新连接两组 MAIN INPUT接口与接线其中一组电源红灯快速闪亮更换整组电源模块5010: “ pump - refill mode is on” (Warning)“冷却泵 - 补充模式已开启”状态解决方法放映机切换至“补充模式” ，只有冷却 泵开启等冷却液补充完毕，点击“退出补充模式”5042: “ cold mirror fan - speed too low” (Error)“反射镜风扇 - 转速过低”5043: “ cold mirror fan - speed low” (Warning)“反射镜风扇 -

4、转速低”5052: “ engine fan - speed too low” (Error)“引擎风扇 - 转速过低”5053: “ engine fan - speed low” (Warning)“引擎风扇 - 转速低”5062: “ heat exchanger fan - speed too low” (Error)“散热器风扇 - 转速过低”5063: “ heat exchanger fan - speed low” (Warning)“散热器风扇 - 转速低”5072: “ lamp anode fan - speed too low” (Error)“灯阳极风扇 - 转速过低

5、”5073: “ lamp anode fan - speed low ” (Warning)“灯阳极风扇 - 转速低”5082: “ lamp cathode fan - speed too low” (Error)“灯阴极风扇 - 转速过低”5083: “ lamp cathode fan - speed low” (Warning)“灯阴极风扇 - 转速低”(Error)5102: “ smps fan 1 - speed too low“开关电源风扇 1 - 转速过低”5103: “ smps fan 1 - speed low ” (Warning)“开关电源风扇 1 - 转速低”5

6、112: “ smps fan 2 - speed too low” (Error)“开关电源风扇 2 - 转速过低”5113: “ smps fan 2 - speed low ” (Warning)“开关电源风扇 2 - 转速低”5122: “ lamp rear fan - speed too low” (Error)“灯后部风扇 - 转速过低”5123: “ lamp rear fan - speed low” (Warning)“灯后部风扇 - 转速低”5132: “ elcabox fan - speed too low” (Error)“电控盒风扇 - 转速过低”5133: “

7、elcabox fan - speed low” (Error)“电控盒风扇 - 转速低”5160: “ engine switch - not ok” (Error)“引擎开关 - 不正常”5170: “ fib - not connected” (Error)“解码板 - 未连接”5180: “ lamp house - not connected ” (Error)“灯箱 - 未连接”状态解决方法灯箱未正确安装检查灯箱是否已正确牢固安装， 确认三 颗锁定螺丝已锁紧开关损坏或未接触检查灯箱右下角固定螺丝对应的放映机内侧微动开关是否损坏或未接触风扇控制板失灵更换5191: “ prism s

8、witch - warning (lens probably touches prism) ” (Warning)“棱镜开关 - 警告(镜头可能已触动棱镜) ”状态解决方法镜头转动至极限， 已触动到棱镜传感器重新调整镜头位置棱镜传感器失效拆除镜头并重启放映机， 若仍有警告则 为棱镜传感器失效5212: “ pump - speed too low ” (Error)“冷却泵 - 转速过低”5213: “ pump - speed low ” (Warning)“冷却泵 - 转速低”5230: “ lens zoom position - requested target not reached

9、” (Warning)“镜头变焦位置 - 没有达到预定位置”状态解决方法所使用的为手动镜头更换电动镜头并设置镜头参数已激活镜头文件无法驱动已安装镜头检查镜头型号设置是否正确镜头文件损坏删除并重建所有现有镜头文件镜头预定位置已非常接近电动镜头机械极限手动重置镜头，或重置放映机位置镜头马达失灵使用小面板上的镜头位置控制按钮， 若 无反应，则为镜头马达失灵5232: “ lens horizontal shift position - requested target not reached (Warning)镜头水平移动位置 - 没有达到预定位置”状态解决方法镜头文件损坏参见 5230镜头预定位置

10、已非常接近电动镜头机械极限手动重置镜头，或重置放映机位置镜头马达失灵使用小面板上的镜头位置控制按钮， 若 无反应，则为镜头马达失灵5233: “ lens vertical shift position - requested target not reached (Warning)“镜头垂直移动位置 - 没有达到预定位置”参见 52325237: “ lens position - clear requested target time out failed (Warning)“镜头位置 - 接受明确指令超时”5280: “ ambient - temperature too high” (

11、Error)“环境 - 环境温度过高”状态解决方法前滤网堵塞清洗或更换环境温度过高降低环境温度抽风设备失灵修复抽风设备5281: “ ambient - temperature high” (Warning)“环境 - 环境温度高”参见 52805283: “ ambient - temperature low” (Warning)“环境 - 温度低”5284: “ ambient - temperature sensor open” (Error)环境 -环境温感器断路”5285: “ ambient - temperature sensor short” (Error)“环境 - 环境温感

12、器短路”5290: “ dmd blue - temperature too high” (Error)“蓝 DMD - 温度过高”5291: “ dmd blue - temperature high” (Warning)“蓝 DMD - 温度高”5293: “ dmd blue - temperature low ” (Warning)“蓝 DMD - 温度低”5294: “ dmd blue - temperature sensor open” (Error)“蓝 DMD - 温感器断路”5295: “ dmd blue - temperature sensor short” (Erro

13、r)“蓝 DMD - 温感器短路”5300: “ dmd green - temperature too high” (Error)“绿 DMD - 温度过高”5301: “ dmd green - temperature high ” (Warning)“绿 DMD - 温度高”5303: “ dmd green - temperature low ” (Warning)“绿 DMD - 温度低”5304: “ dmd green - temperature sensor open” (Error)“绿 DMD - 温感器断路”5305: “ dmd green - temperature

14、sensor short” (Error)“绿 DMD - 温感器短路”5310: “ lamp - temperature too high” (Error)“灯 - 温度过高”状态解决方法滤网堵塞清洗或更换滤网环境温度过高降低环境温度抽风设备失灵修复抽风设备氙灯阴/ 阳极风扇失灵检查阴/ 阳极风扇转速及电压5311: “ lamp - temperature high” (Warning)“灯 - 温度高”参见 53105314: “ lamp - temperature sensor open” (Error)“灯 - 温感器断路”5315: “ lamp - temperature s

15、ensor short” (Error)“灯 - 温感器短路”5320: “ fcb - force lps off” (Error)“风扇控制板 - 灯电源强制关闭”5330: “ pfc heatsink - temperature too high” (Error)“散热器 - 温度过高”5331: “ pfc heatsink - temperature high” (Warning)“散热器 - 温度高”5340: “ dmd red - temperature too high” (Error)“红 DMD - 温度过高”5341: “ dmd red - temperature

16、high” (Warning)“红 DMD - 温度高”(Warning)5343: “ dmd red - temperature low红 DMD - 温度低”(Error)5344: “ dmd red - temperature sensor open“红 DMD - 温感器断路”5345: “ dmd red - temperature sensor short” (Error)“红 DMD - 温感器短路”5350: “ smps primary heatsink - temperature too high” (Error)“开关电源主散热器 - 温度过高”5351: “ smp

17、s primary heatsink - temperature high” (Warning)“开关电源主散热器 - 温度高”5360: “ smps secundary heatsink - temperature too high” (Error)“开关电源副散热器 - 温度过高”5361: “ smps secundary heatsink - temperature high” (Warning)“开关电源副散热器 - 温度过高”5364: “ smps secundary heatsink - temperature sensor open” (Error)“开关电源副散热器 -

18、温感器断路”5365: “ smps secundary heatsink - temperature sensor short” (Error)“开关电源副散热器 - 温感器短路”5401: “ +30v - voltage high ” (Warning)“ +30v - 电压高”5403: “ +30v - voltage low ” (Warning)“+30v - 电压低”5411: “ +5v - voltage high ” (Warning)“ +5v - 电压高”5413: “ +5v - voltage low ” (Warning)“ +5v - 电压低”(Warning

19、)5431: “ cold mirror fan - voltage high“反射镜风扇 - 电压高”5432: “ cold mirror fan - voltage too low” (Error)“反射镜风扇 - 电压过低”5433: “ cold mirror fan - voltage low” (Warning)“反射镜风扇 - 电压低”5441: “ engine fan - voltage high” (Warning)“引擎风扇 - 电压高”5442: “ engine fan - voltage too low” (Error)“引擎风扇 - 电压过低”5443: “ e

20、ngine fan - voltage low” (Warning)“引擎风扇 - 电压低”5451: “ heat exchanger fan - voltage high” (Warning)“换热器风扇 - 电压高”5452: “ heat exchanger fan - voltage too low” (Error)“换热器风扇 - 电压过低”5453: “ heat exchanger fan - voltage low” (Warning)“换热器风扇 - 电压低”5461: “ lamp anode fan - voltage high” (Warning)“灯阳极风扇 - 电

21、压高”5462: “ lamp anode fan - voltage too low” (Error)“灯阳极风扇 - 电压过低”5463: “ lamp anode fan - voltage low” (Warning)“灯阳极风扇 - 电压低”(Warning)5471: “ lamp cathode fan - voltage high“灯阴极风扇 - 电压高”5472: “ lamp cathode fan - voltage too low” (Error)“灯阴极风扇 - 电压过低”5473: “ lamp cathode fan - voltage low” (Warning

22、)“灯阴极风扇 - 电压低”5492: “ smps fan - voltage too low” (Error)“风扇控制板风扇 - 电压过低”5493: “ smps fan - voltage low” (Warning)“风扇控制板风扇 - 电压低”5501: “ fib +12v - voltage high” (Warning)“解码板 +12v - 电压过高”5503: “ fib +12v - voltage low” (Warning)“解码板 + 12v - 电压低”5521: “ motor (lens, dowser) - voltage high” (Warning)

23、“马达(镜头、光闸) - 电压高”5523: “ motor (lens, dowser) - voltage low” (Warning)“马达(镜头、光闸) - 电压低”5531: “ pump - voltage high ” (Warning)“冷却泵 - 电压高”5532: “ pump - voltage too low ” (Error)“冷却泵 - 电压过低”5533: “ pump - voltage low ” (Warning)冷却泵 - 电压低”(Warning)5551: “ tec - voltage high“珀耳贴致冷器 - 电压高”5553: “ tec -

24、voltage low” (Warning)“珀耳贴致冷器 - 电压低”5561: “ elcabox fan - voltage high” (Warning)“电控盒风扇 - 电压高”5562: “ elcabox fan - voltage too low” (Error)“电控盒风扇 - 电压过低”5563: “ elcabox fan - voltage low” (Warning)“电控盒风扇 - 电压低”5571: “ lamp rear fan - voltage high” (Warning)“灯后部风扇 - 电压高”5572: “ lamp rear fan - volta

25、ge too low” (Error)“灯后部风扇 - 电压过低”5581: “ +12v - voltage high ” (Warning)“ +12v - 电压高”5583: “ +12v - voltage low ” (Warning)“+12v - 电压低”5640: “lamp power supplies - zero lamp power supplies detected ” (Error) “灯电源 - 没有探测到灯电源”状态解决方法两电源模块其中之一主供电电缆断开检查电源模块上 MAINSI NPUT插槽及插 线电源模块中“ CTRL IN”与“ CTRL OU”T检查

26、电源模块中“ CTRL IN”与“ CTRL插线断开OUT”插槽及插线电源模块未安装到位重新安装灯电源控制板失灵更换灯电源模块闪红灯更换电源模块5641: “ lamp power supplies - lamp is on, but smps is off” (Error)状态解决方法开关电源板失灵更换灯电源模块失灵更换电源背板失灵更换5642: “ lamp power supplies - at least one lamp power supply could not be detected ” (Error)参见 56405643: “ lamp power supplies - c

27、ommunication failed with at least one lamp power supply ”(Error)参见 56405644: “ lamp power supplies - lamp is on, but at least one lamp power supply is off ” (Error)参见 56405646: “ lamp - set lamp on failed” (Error)“灯 - 点灯失败”状态解决方法氙灯有触发，无法持续点燃1，氙灯寿命将尽，更换新灯2，触发器损坏5647: “ lamp - lamp is off due to an er

28、ror” (Error)“灯 - 由于一个错误氙灯已熄灭”状态解决方法由于某些错误，灯电源被指令熄灭氙灯查看放映机日志寻找其他错误信息， 首 先解决此类错误问题灯电源故障查看灯电源指示灯，若红灯闪烁则更需换灯电源氙灯缺陷更换新灯110.Code 5654: “ lamp run time - read failed” (Error)“灯运行时间 - 读取失败”111.Code 5657: “ lamp run time - exceeds maximum ” (Error)“灯运行时间 - 已到最大寿命”状态解决方法灯箱内氙灯已达到最大使用寿命更换新灯，或重置灯信息5658: “ lamp r

29、un time - read limits failed” (Error)“灯运行时间 - 限制读取失败”113.Code 5659: “ lamp run time - warning ” (Warning)状态解决方法灯箱内氙灯接近到最大使用寿命尽快更换新灯，或重置灯信息114.Code 5800: “ ti-boards - system status = fail” (Error)“TI 板 - 系统状态 =失败”这是一个通用 TI 错误代码，需要进入触摸屏的“诊断 - 测试- 自检”中勾选 所有选项并进行检测，并将检测结果提供给服务商用以查找具体故障所在。 115.Code 5801

30、: “ti-boards - security error, please authorize ” (Error)TI 板 - 安全错误，请授权”状态解决方法放映机的输入或通讯组件被物理重置使用授权钥匙进行重新授权， 步骤如下1，确保重置部件正确安装2，开启放映机3，将授权钥匙嵌入授权插槽4，在 5 秒内输入口令放映机内盖被拆开（光处理器部分）方法同上安全开关失灵如果执行以上方法仍无效， 更换 DCI 安 全开关电源背板失灵如果更换安全开关无效则更换电源背板5802: “ ti-boards - power up self test = fail” (Error)“ TI 板 - 开机自检 -

31、 失败”117. Code 5803: “ti-boards - interface board arm status = fail ” (Error)“ TI 板 - 接口板装载状态 = 失败”118. Code 5804: “ti-boards - interface board fpga load status = fail(Error)“ TI 板 - 接口板 FPGA装载状态 = 失败”119. Code 5805: “ti-boards - processor board dsp status = fail ” (Error)“ TI 板 - 运算板 DSP状态 = 失败”120.

32、 Code 5806: “ti-boards - processor board fpga load status = fail(Error)“ TI 板 - 运算板 FPGA装载状态 = 失败”121. Code 5807: “ ti-boards - read system status failed” (Error)“ TI 板 - 系统状态读取失败”122. Code 5810: “ ti-boards - read power-good failed” (Error)“ TI 板 - 读取电源状态失败”123. Code 5811: “ ti-boards - power-good

33、= fail” (Error)TI 板 - 电源正常信号 = 失败”124.Code 5820:“ti-boards - interface board security enclosure errorreplace interface board ” (Error)TI 板 - 接口板安全外壳错误 - 更换接口板”125.Code 5880:“dolby 3d key-server - read status failed” (Warning)“杜比 3D服务 -状态读取失败”126.Code 5881:“ dolby 3d key-server - status = locked” (Wa

34、rning)“杜比 3D服务 -状态 = 锁定”127.Code 5882:“ 3d module - read status failed” (Warning)“杜比 3D模块 -状态读取失败”128.Code 5885:“ 3d module - change status failed due to communicationerror ” (Error)“杜比 3D模块 -由于通讯故障导致的状态更新失败”5890: “ 3d module - color wheel spin failed” (Error)“杜比 3D模块 -色轮旋转失败”5891: “ 3d module - col

35、or wheel in failed” (Error)“杜比 3D模块 -色轮嵌入失败”131.Code 5892:“ 3d module - color wheel out failed” (Error)“杜比 3D模块 -色轮撤出失败”132.Code 5893:“3d module - color wheel temperature too high ” (Error)“杜比 3D模块 -色轮温度过高”133.Code 5894:“ 3d module - color wheel speed not ok (not locked)”(Error)“杜比 3D模块 -色轮转速不正常（未锁定

36、） ”134.Code 5960:“ light pipe - temperature too high” (Error)光路 - 温度过高”状态解决方法液冷循环中断检查液冷循环管道是否正常光处理器的液冷管道被错误连接将光处理器的液冷管道与冷却泵和换热器重新连接冷却泵未启动检查冷却泵电压换热器的抽气滤网堵塞清理或更换放映机下部的滤网冷却液不足， 冷却泵抽气并且运行声音 变大排除冷却循环中的空气， 重新添加冷却 液液冷循环系统故障， 开启补充模式时感觉不到冷却泵的振动1，检查泵电压2，排出所有冷却液，打开冷却泵查看其转子是否被阻塞温感器失灵更换氙灯位置有误重新调整氙灯位置反射镜位置有误调整反射镜

37、位置135. Code 5961: “ light pipe - temperature high” (Warning)“光路 - 温度高”同 5960136. Code 5964: “ light pipe - temperature sensor open” (Error)“光路 - 温感器断路”137. Code 5965: “ light pipe - temperature sensor short” (Error)“光路 - 温感器短路”5970: “ dmd red front - temperature too high” (Error)“红 DMD前端 - 温度过高”139.

38、Code 5971: “ dmd red front - temperature high” (Warning)“红 DMD前端 - 温度高”140.Code 5973: “红 DMD前端 - 141.Code 5974: “红 DMD前端 - 142.Code 5975: “红 DMD前端 - 143.Code 5980: “绿 DMD前端 - 144.Code 5981: “绿 DMD前端 - 145.Code 5983: “绿 DMD前端 - 146.Code 5984: “绿 DMD前端 - 147.Code 5985: “绿 DMD前端 - 148.Code 5990: “蓝 DMD

39、前端 - 149.Code 5991: “蓝 DMD前端 - 150.Code 5993: “蓝 DMD前端 - 151.Code 5994:“ dmd red front - temperature low” (Warning)温度低”“ dmd red front - temperature sensor open” (Error)温感器断路”“ dmd red front - temperature sensor short” (Error)温感器短路”“ dmd green front - temperature too high” (Error)温度过高”“ dmd green fr

40、ont - temperature high” (Warning)温度高”“ dmd green front - temperature low” (Warning)温度低”“ dmd green front - temperature sensor open” (Error)温感器断路”“dmd green front - temperature sensor short” (Error)温感器短路”“ dmd blue front - temperature too high” (Error)温度过高”“ dmd blue front - temperature high” (Warnin

41、g)温度高”“ dmd blue front - temperature low” (Warning)温度低”“ dmd blue front - temperature sensor open” (Error)蓝 DMD前端 - 温感器断路”152.Code 5995:dmd blue front - temperature sensor short(Error)蓝 DMD前端 - 温感器短路”153. Code 6000: “ block front - temperature too high” (Error)“前冷却块 - 温度过高”154. Code 6001: “ block front - temperature high” (Warning)“前冷却块 - 温度高”155. Code 6004: “ block front - temperature sensor open” (Error)“前冷却块 - 温感器断路”156. Code 6005: “ block front - temperature sensor short” (Error)“前冷却块 - 温感器短路”157. Code 6010: “ block red - temperature too high” (Error)“红色冷