SDTJXZ-RQ-029进口压力容器产品安全性能监督检验实施细则

1、1进口压力容器产品安全性能监督检验实施细则总则Chapter 1 Gen eral Provisi ons1、为保证进口压力容器产品制造质量监督检验质量，制订本细则。1 This outl ine is formulated in order to en sure effective supervisory in spect ion of the pressure vessel products imported2、与进口压力容器产品制造质量监督检验有关各方及人员，均应遵守本细则。2 This outl ine is applicable to whom releva nt to the su

2、pervisory in specti on for safety performa nee of the pressure vessel products imported二、依据Chapter 2 Supervisory In spect ion Basis1、 中华人民共和国国务院令第373号特种设备安全监察条例；1 Special Equipment Safety Supervision Regulation (Promulgated by Decree No. 373 of the State Council of the Peoples Republic of China)2、中华

3、人民共和国国家质量监督检验检疫总局令第 22号锅 炉压力容器制造监督管理办法；2Supervisi on Adm ini strati onRegulati on for Manu facture Lice nsing of Boiler and Pressure Vessel.(Promulgated by Decree No. 22 of General Administration of Quality Supervision. Inspection and Quarantine of the People s Republic of China3、压力容器安全技术监察规程；3 Supe

4、rvisi on Regulati on on the Safety Tech no logy for Pressure Vessel.( Promulgated by Safety Supervisi onDepartment of General Administration of Quality Supervision. Inspection and Quarantine of the People s Republic of China)4、锅炉压力容器产品安全性能监督检验规则。4 Supervisory In spect ion Rule for Safety Performa ne

5、e of Boiler and Pressure Vessel Products. ( Promulgated by Safety Supervisi on Departme nt of Gen eral Admi nistratio n of Quality Supervisi on. In spect ion and Quara ntine of the People s Republic of China三、监督检验内容Chapter 3 Contents of Supervisory In spect ion1、对压力容器制造过程中涉及安全性能的项目进行监督检验；1.Superviso

6、ry inspecting the items related to the safety performanee of the product during pressure vessel manu facturi ng.2、 对受检企业压力容器制造质量体系运转情况进行监督检查。2. Supervisory exam ining the impleme ntati on of the quality system of the supervised manu facturer.四、监检项目和方法Chapter 4 Items and Methods of Supervisory In spe

7、ct ion1、图样资料1. Draw ing and data(1) 检查压力容器设计单位的设计资格印章，确认资格有效。(1) Exam ine the certificate of pressure vessel desig ner, con firm the effective ness of its qualificatio n.(2)审查压力容器制造和检验标准的有效性。2(2)Review the effective ness of sta ndards on manufacture and in spect ion for pressure vessel.(3)审查设计变更(含材料

8、代用)手续。(3) Review the approval formalities for desig n cha nge (in cludi ng material substituti on).2、材料2.Materials(1)审查材料质量证明书、材料复检报告。(1)Check material certificate and material re-test report.(2)检查材料标记移植。(2) Check the transplantation of material identification.(3)审查主要受压元件材料的选用和材料代用手续。(3)Check the se

9、lect ion and formalities of substitute materials for main pressure parts.(4)根据ASME某些材料的特殊要求，确认焊接、热处理、加工工艺及检验工艺的正确性。(4)C onfirm the con formity of weldi ng procedure, heat-treatme nt, process ing procedure and in spect ion procedure with the special requireme nts of accord ing some material to ASME c

10、ode.3、焊接3.Weldi ng(1)审查焊接工艺评定及记录，确认产品施焊所采用的焊接工艺符合相关标准、规范。(1)Check the weldi ng procedure qualificati on and their records, verify that the weld ing tech no logy used in product producti on is in accorda nee with the releva nt sta ndards and codes.(2)确认焊接试板数量及制作方法。(2)Confirm the number and manufactur

11、ing method of the welding test plate.(3)审查产品焊接试板性能报告，确认试验结果。(3)Check the property test report of the product welding test plates and confirm the test results.(4 )检查焊工钢印。(4)Check ide ntificati on steel stamps of welders and weld ing operators.(5)审查焊缝返修的审批手续和返修工艺。(5) Check formalities and procedures f

12、or weldi ng repair.(5)审查焊缝返修的审批手续和返修工艺。4、外观和几何尺寸4.Visual and dime nsional exam in ati on(1)检查焊接接头表面质量。(1) Exami ne the appeara nee of welded joi nts.(2)检查母材表面的机械损伤情况。(2)Check the mecha ni cal damage on the surface of base metal.(3)检查筒体内径与最小内径差，当直立容器壳体长度超过30m时，检查筒体直线度。检查焊缝布置和封头形状偏差，并记录实际尺寸。3(3)Check

13、the differenee between maximum and minimum diameters of shell. Check the straightness of the cylinder of vertical vessel with height more than 30 meters, Check the arrangement of welds and the deviation of figure in head and record their actual dime nsions.5、无损检测5.Non-destructive exam in ati on(1 )检

14、查布片(排版)图和探伤报告，核实探伤比例和位置，对局部探伤产品的返修焊缝，应检查扩探 情况。对超声波探伤和表面探伤，除审查报告外，监检人员还应不定期到现场对产品进行实地监检。(1)Check x-ray film arran geme nt map and NDE report. Verify the proport ion and positi on of NDE. For the spot-NDE pressure vessel, check the extension RT for the repaired welds. As for the UT or surface flaw det

15、ecti on, the supervisory in spector should con duct ran dom on-site supervisory in specti on in additi on check ingthe report.(2)抽查底片。抽查数量不少于设备探伤比例的30%，且不少于10张(少于10张的全部检查)，检查部位应包括T形焊缝可疑部位及返修片。(2)Check the x-ray films. The number of the x-ray films being checked should not be less than 30 percent of

16、the whole and should not less tha n 10 films (in cludi ng the x-ray films at T-joint, doubtful area and at the repaired area).6、热处理6.Heat treatme nt检查确认热处理记录曲线和热处理工艺的一致性。Check and confirm the corresp ondence betwee n heat treatme nt curve and actual heat treatme nt parameter and procedure.7、耐压试验7.Pr

17、essure test耐压试验前，应确认需监检的项目均监检合格，受压企业应完成的各项工作均有见证。耐压试验时，监检人员必须亲临现场，检查试验装置、仪表及准备工作，确认试验结果。Before pressure test, confirm that all required items have passed the supervisory in spect ion and the supervised manufacturer has kept the testimony of the whole-completed work. During pressure test, the supervi

18、sory inspector shall check the test equipment, instruments, preparation work for testing and verify the test results on the site.8、安全附件8.Safety appurte nance检查安全附件数量、规格、型号及产品合格证应当符合要求。The number, specifications, types and certificates of complianee of safety appurtenances should meet the requireme n

19、ts.9、气密性试验9.Leak test检查气密性的试验结果，应当符合有关规范、标准及设计图样的要求。Check the leak test result to assure that it meets to the requireme nts of concerned code, sta ndards, and desig n draw ing.10、 出厂技术资料10. Delivery tech ni cal data4（1）审查出厂技术资料。 Check the technical data to be delivered.（2 ）检查铭牌内容应符合有关规定，在铭牌上打监检钢印。（2

20、） Check the n ameplate if the contents on it are in accorda nee with the releva nt requireme nts, if so, stamp the supervisory in spect ion steel seal on the products n ame plate.11、 监检资料11. Supervisory in spect ion data经监检合格的产品，监检人员应当根据压力容器产品安全性能监督检验项目表的要求及时汇总、 审核见证资料，并由监检单位出具监检证书。Once the product

21、has passed the supervisory in spect ion, the supervisory in spector should summarize and verify the testifyi ng paper in time accord ing to the Supervisory In spect ion Items for Safety Performa nee of Pressure Vessel Products and issue the Supervisory In spect ion Certificate.五、监检程序Chapter 5 Superv

22、isory In spect ion Procedure1、受检企业资质、质量体系、人员资格及生产能力确认，内容包括：1.The certificate, quality management system, personnel qualification and production capability of the supervised manu facturer should be con firmed, which in clude:（1）、审查受检企业制造许可证，确认其有效性；（1） Exami ne the certificate of pressure vessel manu

23、facturer; confirm the effective ness of its qualificati on.（2）、审查受检企业的质量体系文件（包括质量手册、程序文件、管理制度、各责任人员的任免文件、质量信息反馈资料等）是否符合要求；（2） Review the Documents on quality system （including quality manual, procedures, management rules, docume nts on appo in tme nt and dismiss of resp on sible pers ons, and qualit

24、y in formati on feedback data）, Con firm that the Docume nts on quality system meet the requireme nts of corresp onding codes.（3）、审查从事锅炉压力容器焊接的持证焊工的持证项目、有效期等是否符合要求；（3） Check the qualified items, terms of validity of the qualified welders. The qualified items, terms of validityof the qualified welder

25、s engaged in the welding of pressure vessel products should meet the requirements of corresp onding codes.（4）、审查从事锅炉压力容器质量检验的人员及从事无损检测人员的持证项目、级别、有效期等是否符 合要求；（4） Check the qualified items, qualified level and terms of validity of the list of staff engaged in non-destructive exam in ati on and quality

26、 in spect ion. Their qualified items, qualified level and terms of validity should meet the requireme nts of corresp onding codes.(5)、审查压力容器的设计资料，工艺文件，制造、检验控制程序，以及焊接工艺评定一览表等；(5)Review the pressure vessel desig n data, manufacture procedure docume nts, manufacture and in spect ion control procedure,

27、as well as the list of welding procedure qualifications.(6)、查看并确认受检企业的生产能力。(6)Check and verify the product ion capability of the supervised manu facturer.2、按监检项目表(见附件)的内容实施监检工作。2.Supervisory inspection should be implemented according to the contents of Supervisory Inspection ltems(Appe ndix 1).(1) 、

28、压力容器产品监检项目分A类和B类。对A类项目，监检员必须到场进行监检，并在受检企业提供的相应的见证文件(检验报告、记录表、卡等，下同)上签字确认；未经监检确认，不得流转至下一道工序。对 B类项目，监检员应到场进行监检，如不能到场监检，可在受检企业自检后，对受检企业5提供的相应见证文件进行审查并签字确认。(1)The Supervisory In spect ion Items of pressure vessel products are classified into Category A and Category B.For the items of Category A, the sup

29、ervisory in spector must con duct supervisory in spect ion on the site andshould sig n on the related testify ing docume nts provided by the supervised manu facturer (in cludi ng in spect ion report, record ing forms and cards; similarly here in after). If the item has not bee n verified via supervi

30、sory in spect ion, the product cannot be tran sferred to the n ext work ing process.For the items of Category B, The supervisory in spector must con duct supervisory in spect ion on the site. If thesupervisor in spect ion is not on the site, he(or she) should check and sig n on the related testify i

31、ng docume nts provided by the supervised manu facturer to validate the self- in spect ion of the manu facturer.(2)、受检单位企业发生质量体系运转和产品安全性能违反有关规定的一般问题时，监检员应当向受检企业发出锅炉压力容器产品安全性能监督检验工作联络单；发生违反有关规定的严重问题时，监检单位应当向受检企业签发锅炉压力容器安全性能监督检验意见通知书，并报告国家质检总局安全监察机构。(2)When the supervised manu facturer makes such gen eral mistakes of the impleme ntati on of its quality system or the safety performa nee of its products aga inst the related rules, the in spector should give out the Work Liais on Sheet of Safety Performa nee Super