3GPP LTE141协议

1、3gpp ts 36.141 v10.1.0 (2010-12)technical specification3rd generation partnership project;technical specification group radio access network;evolved universal terrestrial radio access (e-utra);base station (bs) conformance testing(release 10)the present document has been developed within the 3rd gen

2、eration partnership project (3gpp tm) and may be further elaborated for the purposes of 3gpp.the present document has not been subject to any approval process by the 3gpp organizational partners and shall not be implemented.this specification is provided for future development work within 3gpp only.

3、 the organizational partners accept no liability for any use of this specification.specifications and reports for implementation of the 3gpp tm system should be obtained via the 3gpp organizational partners' publications offices.release 101693gpp ts 36.141 v10.1.0 (2010-12)keywordse-utra, base s

4、tation, radio, testing3gpppostal address3gpp support office address650 route des lucioles - sophia antipolisvalbonne - francetel.: +33 4 92 94 42 00 fax: +33 4 93 65 47 16internetcopyright notificationno part may be reproduced except as authorized by written permission.the copyrigh

5、t and the foregoing restriction extend to reproduction in all media.© 2010, 3gpp organizational partners (arib, atis, ccsa, etsi, tta, ttc).all rights reserved.umts is a trade mark of etsi registered for the benefit of its members3gpp is a trade mark of etsi registered for the benefit of its me

6、mbers and of the 3gpp organizational partnerslte is a trade mark of etsi currently being registered for the benefit of its members and of the 3gpp organizational partnersgsm® and the gsm logo are registered and owned by the gsm associationcontentsforeword101scope112references113definitions, sym

7、bols and abbreviations123.1definitions123.2symbols133.3abbreviations144general test conditions and declarations154.1measurement uncertainties and test requirements154.1.1general154.1.2acceptable uncertainty of test systemmeasurement of transmittermeasurement of receivermea

8、surement of performance requirement204.1.3interpretation of measurement results224.2base station classes224.3regional requirements234.4selection of configurations for testing244.5bs configurations254.5.1transmit configurationstransmit diversity and mimo transmission254.5.2receive configurat

9、ionsreceiver diversity264.5.3duplexers264.5.4power supply options264.5.5ancillary rf amplifiers264.5.6bs with integrated iuant bs modem274.5.7bs using antenna arrays2receiver tests2transmitter tests284.6manufacturers declarations of regional and optional requirements284.6.1o

10、perating band and frequency range284.6.2channel bandwidth294.6.3base station output power294.6.4spurious emissions category294.6.5additional operating band unwanted emissions294.6.6co-existence with other systems294.6.7co-location with other base stations304.7specified frequency range and supported

11、channel bandwidth304.8format and interpretation of tests305operating bands and channel arrangement325.1general325.2void325.3void325.4void325.5operating bands325.6channel bandwidth335.7channel arrangement345.7.1channel spacing345.7.2channel raster345.7.3carrier frequency and earfcn346transmitter char

12、acteristics366.1general366.1.1e-utra test models3e-utra test model 1.1 (e-tm1.1)3e-utra test model 1.2 (e-tm1.2)3e-utra test model 2 (e-tm2)3e-utra test model 3.1 (e-tm3.1)4e-utra test model 3.2 (e-tm3.2)4e-utra test model 3.3 (e-tm3.3)456.1.2data cont

13、ent of physical channels and signals4reference signals4primary synchronization signal4secondary synchronization signal4pbch4pcfich4phich4pdcch4pdsch486.2base station output power496.2.1definition and applicability496.2.2minimum requirem

14、ent506.2.3test purpose506.2.4method of test50initial conditions50procedure506.2.5test requirements506.2.6home bs output power for adjacent utra channel protection50definition and applicability50minimum requirement5test purpose5method of test5.1init

15、ial conditions5.2procedure5test requirements526.2.7home bs output power for adjacent e-utra channel protection5definition and applicability5minimum requirement5test purpose5method of test5.1initial conditions5.2procedure5test re

16、quirements546.3output power dynamics546.3.1re power control dynamic range5definition and applicability5minimum requirement5method of test556.3.2total power dynamic range5definition and applicability5minimum requirement5test purpose5method of te

17、st5.1initial conditions5.2procedure5test requirement566.4transmit on/off power566.4.1transmitter off power5definition and applicability5minimum requirement5test purpose5method of test5.1void5.2void5test requirement566.4.

18、2transmitter transient period5definition and applicability5minimum requirement5test purpose5method of test5.1initial conditions5.2procedure5test requirement576.5transmitted signal quality586.5.1frequency error5definition and applicabili

19、ty5minimum requirement5test purpose5method of test5test requirement586.5.2error vector magnitude5definition and applicability5minimum requirement5test purpose5method of test5.1initial conditions5.2procedure5test

20、requirement596.5.3time alignment between transmitter branches60definition and applicability60minimum requirement60test purpose60method of test60.1initial conditions60.2procedure60test requirement616.5.4dl rs power6definition and applicability6

21、minimum requirement6test purpose6method of test6.1initial conditions6.2procedure6test requirement616.6unwanted emissions616.6.1occupied bandwidth6definition and applicability6minimum requirements6test purpose6method of t

22、est6.1initial conditions6.2procedure6test requirements636.6.2adjacent channel leakage power ratio (aclr)6definition and applicability6minimum requirement6test purpose6method of test6.1initial conditions6.2procedure6test

23、requirement646.6.3operating band unwanted emissions6definition and applicability6minimum requirement6test purpose6method of test6.1initial conditions6.2procedure6test requirement6.1test requirements for wide area bs (category a)666.6.3.

24、5.2test requirements for wide area bs (category b)6.2.1category b test requirements (option 1)6.2.2category b (option 2)70.2atest requirements for local area bs (category a and b)7.2xtest requirements for home bs (category a and b)7.3additional requirements736.

25、6.4transmitter spurious emissions7definition and applicability7minimum requirements7test purpose7method of test7.1initial conditions7.2procedure7test requirements7.1spurious emissions (category a)7.2spurious emissions (category

26、b)7.3protection of the bs receiver of own or different bs7.4co-existence with other systems in the same geographical area7.5co-location with other base stations836.7transmitter intermodulation876.7.1definition and applicability876.7.2minimum requirement876.7.3test purpose876.

27、7.4method of test8initial conditions8procedures886.7.5test requirements887receiver characteristics897.1general897.2reference sensitivity level897.2.1definition and applicability897.2.2minimum requirement897.2.3test purpose897.2.4method of testing8initial conditions8pr

28、ocedure897.2.5test requirement907.3dynamic range917.3.1definition and applicability917.3.2minimum requirement917.3.3test purpose917.3.4method of testing9initial conditions9procedure917.3.5test requirements917.4in-channel selectivity937.4.1definition and applicability937.4.2minimum re

29、quirement947.4.3test purpose947.4.4method of testing9initial conditions9procedure947.4.5test requirements957.5adjacent channel selectivity (acs) and narrow-band blocking967.5.1definition and applicability967.5.2minimum requirement967.5.3test purpose977.5.4method of test9initi

30、al conditions9procedure for adjacent channel selectivity9procedure for narrow-band blocking977.5.5test requirements977.6blocking1007.6.1definition and applicability1007.6.2minimum requirements1007.6.3test purpose1007.6.4method of test100initial conditions100procedure101

31、7.6.5test requirements10general requirement10co-location with other base stations1047.7receiver spurious emissions1097.7.1definition and applicability1097.7.2minimum requirements1097.7.3test purpose1097.7.4method of test10initial conditions10procedure1097.7.5test requ

32、irements1107.8receiver intermodulation1107.8.1definition and applicability1107.8.2minimum requirement1107.8.3test purpose1107.8.4method of test1initial conditions1procedures1117.8.5test requirements1128performance requirement1168.1general1168.2performance requirements for pusch1168

33、.2.1performance requirements of pusch in multipath fading propagation conditions1definition and applicability1minimum requirement1test purpose1method of test1.1initial conditions1.2procedure1test requirement1178.2.2performance requiremen

34、ts for ul timing adjustment1definition and applicability1minimum requirement1test purpose1method of test1.1initial conditions1.2procedure1test requirement1258.2.3performance requirements for harq-ack multiplexed on pusch12definit

35、ion and applicability12minimum requirement12test purpose12method of test12.1initial conditions12.2procedure12test requirement1268.2.4performance requirements for high speed train conditions12definition and applicability12minimum require

36、ment12test purpose12method of test12.1initial conditions12.2procedure12test requirement1288.3performance requirements for pucch1298.3.1ack missed detection for single user pucch format 1a12definition and applicability12minimum requirement1308.3

37、.1.3test purpose130method of test130.1initial conditions130.2procedure130test requirement1308.3.2cqi performance requirements for pucch format 213definition and applicability13minimum requirement13test purpose13method of test13.1ini

38、tial conditions13.2procedure13test requirement1328.3.3ack missed detection for multi user pucch format 1a13definition and applicability13minimum requirement13test purpose13method of test13.1initial conditions13.2procedure13test

39、requirement1348.4performance requirements for prach1348.4.1prach false alarm probability and missed detection13definition and applicability13minimum requirement13test purpose13method of test13.1initial conditions13.2procedure13test requirement1

40、36annex a (normative):reference measurement channels137a.0general137a.1fixed reference channels for reference sensitivity and in-channel selectivity (qpsk, r=1/3)137a.2fixed reference channels for dynamic range (16qam, r=2/3)138a.3fixed reference channels for performance requirements (qpsk 1/3)138a.

41、4fixed reference channels for performance requirements (16qam 3/4)139a.5fixed reference channels for performance requirements (64qam 5/6)139a.6prach test preambles139a.7fixed reference channels for ul timing adjustment (scenario 1)140a.8fixed reference channels for ul timing adjustment (scenario 2)1

42、40a.9multi user pucch test140annex b (normative):propagation conditions142b.1static propagation condition142b.2multi-path fading propagation conditions142b.3high speed train condition143b.4moving propagation conditions144annex c (normative):characteristics of the interfering signals146annex d (norma

43、tive):environmental requirements for the bs equipment147d.1general147d.2normal test environment147d.3 extreme test environment147d.3.1extreme temperature147d.4vibration148d.5power supply148d.6measurement of test environments148annex e (normative):general rules for statistical testing149annex f (norm

44、ative):global in-channel tx-test150f.1general150f.2.1basic principle150f.2.2output signal of the tx under test150f.2.3reference signal150f.2.4measurement results150f.2.5measurement points151f.3.1pre fft minimization process151f.3.2timing of the fft window152f.3.3resource element tx power152f.3.4post

45、 fft equalisation153f.4.1evm154f.4.2averaged evm155f.4.2.1averaged evm (tdd)156annex g (informative):test tolerances and derivation of test requirements157g.1measurement of transmitter158g.2measurement of receiver161g.3measurement of performance requirements164annex h (informative):e-utran measureme

46、nt test cases165annex i (informative):measurement system set-up166i.1transmitter166i.1.1base station output power, output power dynamics, transmitted signal quality, frequency error, evm, dl rs power, unwanted emissions166i.1.2transmitter intermodulation166i.1.3time alignment between transmitter bra

47、nches167i.1.4home bs output power for adjacent channel protection167i.2 receiver167i.2.1reference sensitivity level168i.2.2dynamic range168i.2.3in-channel selectivity169i.2.4adjacent channel selectivity (acs) and narrowband blocking170i.2.5blocking characteristics170i.2.6receiver spurious emission17

48、1i.2.7intermodulation characteristics171i.3performance requirement172i.3.1performance requirements for prach in static conditions172i.3.2performance requirements for pusch, prach, single user pucch in multipath fading conditions and for high speed train conditions172i.3.3performance requirements for

49、 multi user pucch in multipath fading conditions173i.3.4performance requirement for ul timing adjustment174annex j (informative):unwanted emission requirements for multi-carrier bs175j.1general175j.2multi-carrier bs of different e-utra channel bandwidths175j.3multi-carrier bs of e-utra and utra175an

50、nex k (informative):change history176forewordthis technical specification has been produced by the 3rd generation partnership project (3gpp).the contents of the present document are subject to continuing work within the tsg and may change following formal tsg approval. should the tsg modify the cont

51、ents of the present document, it will be re-released by the tsg with an identifying change of release date and an increase in version number as follows:version x.y.zwhere:xthe first digit:1presented to tsg for information;2presented to tsg for approval;3or greater indicates tsg approved document und

52、er change control.ythe second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc.zthe third digit is incremented when editorial only changes have been incorporated in the document.1scopethe present document specifies the radio frequency (rf) tes

53、t methods and conformance requirements for e-utra base stations (bs) operating either in the fdd mode (used in paired bands) or the tdd mode (used in unpaired bands). these have been derived from, and are consistent with the e-utra base station (bs) specifications defined in 2.2referencesthe followi

54、ng documents contain provisions which, through reference in this text, constitute provisions of the present document.· references are either specific (identified by date of publication, edition number, version number, etc.) or nonspecific.· for a specific reference, subsequent revisions do

55、 not apply.· for a non-specific reference, the latest version applies. in the case of a reference to a 3gpp document (including a gsm document), a non-specific reference implicitly refers to the latest version of that document in the same release as the present document.13gpp tr 21.905: "vocabu