锂电池规格书

1、充电器规格书Sp ecification of Battery Charger型号：ES2406S6A锂电池充电器（全铝外壳）/ 6A Li Iro n/Li P olymer BATTERY CHARGER1 概述Gen eral此型号2406S 155 X 90 X 30mm勺铝质外壳充电器能在输出6A的情况下工作，具有反接保护功能。Battery Charger 2406S 155 X 90 x 50mm can work normally under6A and with reverse polarityp rotect ion.2. 主要参数Main p roduct sp ecif

2、icati on最大输出功率I输入电压I最高输出电压误差范围输出电流 I误差范围po werInp utvoltageCombi nedOutput curre ntCombi nedvoltageregulati onregulati on180W220Vac+/+/6A+/-0. 2A3. 环境条件En viro nmen tai con diti on序号No.项目Item技术参数Tech ni cal sp ecificatio n备注Remark1湿度Humid辻y"95%带包装 With package2i每拔 Altitudew 3000m正常工作Work normal

3、ly4. 技术特征Electrical characteristics输入特征：Input characteristic序号No.项目Item技术参数 Technical sp ec辻icati on备注Remark1额定输入电压Rated input voltage220Vac220Vac2电压输入范围Input voltage range180-240Vac3频率AC input voltage freque ncy50 60 Hz输岀特征和充电模式:Output characteristic or charge stages序号No.项目Item技术参数Tech ni cal sp ec

4、ificatio n备注Remark1恒流CC(co nsta nt curre nt)w , 6A2恒压CV(co nsta nt voltage),6A J37学充 Float stage无20%CC4效率Po wer efficie ncy> 90%输入电压=220Vac,额定负 载Vin=110/220Vac, ratedload保护特征:Protecti on characteristics序号No.项目Item技术参数Tech nical sp ecificati on备注Remark1过压保护Over voltage p rotectio n是Yes2限压保护Softwar

5、e over voltage protectio n充电器设置的最大输出电压不会超过电池的最大充电电压。The charger software limits the maximumoutput voltage to a level suitableforthe conn ected battery system3过热保护Thermal protectio n否No4限流保护Current limit ing protectio n是Yes恒流At CC mode5短路保护Shortcircuitprotectio n当输出短路时充电器不能正常工作，输出恢复正常，充电器可自行恢复。Short

6、circuitprotectionshould be automaticallyrecovery after remove the con diti on.6反接保护Reverse po larity protectio n当输出线接反后充电器不会工作，直到使用者接正确后方可启动。When out putwires are reverselyconn ected to thebattery the charger will not op erate and will work no rmally whe n DC wires are correctly conn ected充电指示Charg

7、ing in dicator序号No.项目Item状态Status备注Remark1电源 Power onLED1:红灯 Red2充电 ChargingLED2:红灯 Red3充前 Fully chargedLED2：绿灯 Green4输出电压显示Charging Voltage Display否No5输出电流显示Charging Current Display否No5.安全性Safety & EMC序号No.项目Item标准(或测试条件)Stan dard (or test con diti on)备注Remark1耐压测试Electric stre ngthtest输入-输出Inp

8、u t-out put1500Vac/10mA/lmin无故障No breakdow n2绝缘电阻Isolati on输入-接地Inpu t-gro und10Mohm500Vdcresista nee输出-接地Outpu t-ground> 10Mohm500Vdc3泄漏电流 Leakage current<Vin=264Vac4低电压测试LVDEN60335-1:2002+EN60335-2-29:2002备注：辨识A：在技术要求范围内，充电器功能正常;Remark: Discrim in ati on A- Function OK un der tech ni cal req

9、uireme nt ran ge;辨识R：只有由外部干扰信号引起的保护装置（保险丝）损坏，整个设备在更换保护装置和重设运行参数后才能正 常工作，因机械性损坏和设备故障的设备却不能。Discrim in ati on R- Physical damage or failure of equipment of protectionare not allowed, but damage ofdevice (fuse) caused by interference signal the whole equipment can workoutside is allowed, and protection

10、normally after replacement of of running p arameterdevice and reset6.环境测试要求En viro nmen tai test ing requireme nts序号No.项目Item技术参数Tech ni calsp ecificati on备注Remark1最高工作温度High temp erature ambient op erat ing+40C性能正常Features OK2最低工作温度Low temp erature ambient op erat ing-IOC性能正常Features OK3最咼存储温度High

11、temp eraturestorage+70C在恢复正常温度2小时后，充电器能正 常工作。Work normally after recovery un der no rmal temp erature for 2 hours4最低存储温度Low temp erature storage-40C在恢复正常温度2小时后，充电器能正 常工作。Work normally after recovery un der no rmal temp erature for 2 hours5随机振动Ran dom vibrati on20Hz to 2000Hz 3Grms 20hoursper axis6重复

12、震动Rep etitive shock40g p eak 3 orthog onal axes, 3+ and 3- in each axis, 11ms pulse width7热冲击Thermal shock-35Cto75C,< 3mintran siti on, dwell, 200cycle8跌落测试Drop testBS EN60068-2-32:1993 TEST ED: free fallappen dix B7.机械特征Mechanical characteristic:外壳材质：铝Shell material: Aluminum外壳尺寸：长*宽*高二155 X 90

13、X 50毫米Outline dimension: L*W*H= 155 x 90 x 50mm 输入接口 ：通过IEC标准Input socket: meets IEC standard电源线：1.5米长AC wires: 1. 5m length输出线：米长DC wire: 1. 0m length净重：千克Net Weight: 0.9 Kg8.包装，运输方式和存储方式Package, transportation & storage包装 Package:包装盒内有产品名称，型号，生产厂家名称，安全标准，序号，使用说明书以及装箱单。There is product name, mo

14、del, name of manufacturer, safety approval, serial number, User Manual and packing list in the package box运输方式 Transportation :适用于货车装运，产品需放在阴处，装卸时请小心。Suit for transportation by truck, the products should be shielded by tent from sunshine, and loaded and unloaded carefully. 存彳诸方式Storage :当产品不使用时，应放在包

15、装盒内。仓库温度应在-40X0C,相对湿度为595%并且仓库内不能有有害气体，易燃品，爆炸品，腐蚀性等化学物品及强有力的机械震动、冲击和磁场影响。包装盒需放在距离地面至少20cm 高，距离墙，热源，和通风口50cm远。充电器在此种存储条件下可以放两年，超过两年须重新检测。充电器必须每三个月通电一次，通电时间应不少于小时。Products should be stored in package box when it is not used And warehouse temperature should be -40=70 C , and relative humidity is 595% I

16、n the warehouse, there should not be harmful gas, inflammable, explosive products, and corrosive chemical products, and strong mechanical vibration, shock and strong magnetic field affection. The package box should be above ground at least 20cm height, and 50cm away from wall, thermal source, and vent Under this requirement, product has 2 years of storage period, and should be