顶针安装流程

1、半润安盎與您择手改樂生辽无锡华润安盛科技有限公司ESEC & ASM顶针安装流程/The procedure fixing needleof ESEC and ASMWuXi China Resources Micro-Assembly Technology Co.,LTDESEC 顶针安装流程/The procedure fixing needle of ESEC羽閃« « ®手改少生活1 工夹具准备/Preparing the jig and tools顶针/Needle开口扳于或活动扳于/Ringent wrench or monkey wrench

2、夹具/Jig顶针座/Needle holder顶针帽/pepper pot2顶针选取/Selecting needle100um200um娶悠K手改妙牛活3顶针安装/Fixing the needle1 将顶针座放入匚夹具定位孔中 /Plug the needle holder in the jig2 转动把于固定顶针座/Fix the needle holder with gripe3 旋松顶针座的紧固螺帽/Screwthe nut with wrench6個定顶针/Fix the needle4安装顶针/Plug the needle in the needle holder5调整顶针高度

3、（注意：顶针针尖必须 顶在夹具表面，顶销端面必须和夹具 表面贴合）/Adjust the height .The needle and the pin must be pushed against the side of the jig娶悠&手改妙牛活4安装顶针座/Fixing the needle holder带有三个卡槽的顶针基座/The ejector with 3 slots安放顶针在顶针基座上/Plug the needle holder in the ejector安装顶针时要将顶针座上的销钉卡在 基座的卡槽中，然后稍稍用力向下按 紧/Push the he needle

4、holder to make sure the pin be locked by the slot, then press out.娶悠K手改妙牛活两种顶针帽/Two kinds of pepper pot安装顶针帽/Put on the pepper pot安装顶针帽时向下按紧使卡槽卡住销 钉/Press out the pepper pot to make the slot lock the pin5安装顶针帽/Fixing the pepper pot脳劭hi手at » 4=活安装完成/FinishASM顶针安装流程/The procedure fixing needle of

5、 ASM«手改妙牛活1 工夹具准备/Preparing the jig and tools紧固螺母/Nut夹具/Jig开口扳于或活动扳于顶针帽/pepper pot顶针座/Needle holder/Ringent wrench or monkey wrench2顶针选取/Selecting needle100um200um娶悠K手改妙牛活3顶针安装/Fixing the needle2 安装顶针/Plug the needle in the needle holder1 将顶针座安装在夹具定位销 上，旋松紧固螺母/Put the needle holder on the pin o

6、f the jig,then unscrew the nut娶悠K手改妙牛活4 用开口扳手或活动扳 手旋紧紧固螺母，固定 顶针/Fixing the needle with wrench3调整顶针高度（注意：顶针针 尖必须顶在夹具表而，顶销端 面必须和夹具表面贴合。） /Adjust the height. The needle and the pin must be pushed against the side of the jigwM悠&手改妙牛活4安装顶针座/Fixing the needle holder带有定位销的顶针基座/The ejector with pin安装顶针在

7、顶针基座上。（顶针座的卡 槽要卡在基座定位销上，然后用力向下 压紧）/Plug the needle holder in the ejector,make sure the slot lock the pin of the ejector ,then press out娶悠&手改妙牛活5安装顶针帽/Fixing the pepper pot安装顶针帽（使顶针帽上的卡 槽卡住定位销，向下按紧）/Put on the pepper pot Press out the pepper pot to make sure the slot lock the pin用2.0的六角扳手旋紧紧固顶丝/S

8、crew the bolts with wrench to fix the pepper pot娶悠K手改妙牛活When finished the changing, please do the “Teach Z-height5 顶针更换好之后，必须定义顶针的初始高度。1. 1. For ESEC2007 the menu is "Assist - Pick & place tools : Needle up /Needle down / Define needle”.对于ESEC2007按照菜单：“ “Assist - Pick & place tools : Ne

9、edle up / Needle down / Define needle”.来定义顶针初始高度。2. 2. For ESEC2008 the menu is "Teach 一 Pick & Place 一 Extended pickup process: Teach Z-heightn.对于ESEC2008按照菜单 “Teach - Pick & Place - Extended pickup process: Teach Z-heightn.设备会自动校正顶针高度。3. 3. For ASM AD828 the menu is "Set up 一 Pick & Place 一 Ejector Posns： Ref对于ASM AD828按照菜单 “Set up 一 Pick & Place 一 Ejector Posns： Ref ”来定义 顶针初始高度。4. 4. For ASM AD889 the