申请CCC强制认证产品描述

1、申请CCC强制认证产品描述(低压电器类)Product Description For China Compulsory Certification(Low-voltage Products)申请编号(Application No.)申请人(Applicant)地址(Applicant 's Address)工厂编号(Factory s Code)生厂厂(Factory)地址(Factory 's Address)产品名称(Name of Product)转换开关电器(CB级)(TSE(Class CB)型号(Model)申请单位（印章）Applicant 's sea

2、l here企业自我声明1(Applicant Declaration 1)本企业在此郑重声明：本次申请中，我单位向指定检测机构提供的型号/规格为 的(产品名称)是由(生产厂名称)于(生产厂地址) 完成最终装配和出厂检验。本企业对提以上情况的真实性负责，否则由此引起任何事情由本企业将承担全 部责任。Herein we solemnly declare that the final assemble and routine tests of(product name) under (model type and specification) within this application are

3、 done by (factory name) in (factory address).We guarantee the truth of the above declaration; otherwise we are willing to assume any possible consequences.申证企业负责人(签名)：Applicant s principal(signature)日期(Date):(企业盖章)(Applicant s seal here)企业自我声明2(Applicant Declaration 2)企业名称(Applicant):申证广品名称、型号规格(Pro

4、duct Name and Mode):注册商标(Trade Mark):本企业在此郑重声明：上述申证产品所使用的型号和商标保证严格遵守国家有 关法律法规和政府部门的有关规定。如有乱用、冒用其他企业产品的型号和商标导 致侵权行为，本企业将对其后果承担全部法律责任。本企业对提供所有与认证有关资料的真实性负责。如果本企业获证的产品有所变更，将及时提交产品变更报告，否则由此引起任何事情由本企业将承担全部责任。Herein we solemnly declare: all the modes and trademarks of the above-applied product are strictl

5、y complied with the relevant laws, stipulations and governmental regulations. We will bear all the law liability in case of infringement of the modes and trademarks of other manufactures.We are liable for the authenticity of all the documentation we submit for CCC approval. We will keepyou informed

6、in case of product changes by submitting product change report; otherwise we will bear responsibilities for all the consequences arising therefore.申证企业负责人(签名)：Applicant s principal(signature)日期(Date):(企业盖章)(Applicant s' seal here)产品描述(Product Description)1.产品构成的描述及结构特点(结构概要说明):Product ' s co

7、mposing and construction characteristics (brief description of the construction ):包括产品的主要组成部件，操作方式，安装方式，接线方式等，还包括以下内容：For the main parts of the product, operation mode, installation mode and connection mode, etc., and the following information should be also submitted:1)产品型号及名称 (Product s Mode and N

8、ame): 转换控制器型号规格 (Type/Model of TSE controller): 2)额定工作电压Ue:3)额定工作电流Ie:4)极数(Pole): 5)产品是否适用于隔离 (Whethe门t is applicable for isolation):是(Yes);否(No)6)提供图纸及编号(Drawings offered and their serial numbers):总装配图(General assembly diagram):电子组件板原理图(Electronic board Schematic diagram):印刷板布置图(Layout of PCB):7)产品

9、的转换控制方式 (Control mode of transfer):手动操作转换开关电器MTSE;遥控操作转换开关电器RTSE;自动转换开关电器 ATSE8)产品特性(Product characteristic):非派生的转换开关电器(Non-derived TSE); 派生的转换开关电器(Derived TSE)9)产品主体部分的开关元件的名称、型号规格及获证的CCC编号(Situation of Component switches inmain body, including products ' name, model/type, CCC certificates numb

10、er): 产品描述(Product Description)2 .主要技术参数(Main technical Parameter):(1)使用类别(Utilization Category):(2)额定冲击耐受电压 Uimp: (3)额定绝缘电压 Ui:(4)约定发热电流 Ith:(5)额定短路接通能力Icm (峰值Peak Value): (6)额定短路分断能力Icn:(7)外壳防护等级(IP):(8)电磁兼容设备发射等级(Emission class of EMC equipment):DA 级；DB 级(9)电源电压偏差和频率偏差(Voltage supply deviation and

11、 frequency supply deviation):(10)触头转换时间 (Contact transfer time): 转换动作时间(Operating transfer time): 返回转换时间(Return transfer time):断电时间(包括延日时间)范围(Off time range(including time-delay): (11)接线端子连接导线能力(Terminals ; wiring capability):(通常指连接硬线的能力Capability for connecting with hardline)最大导线截面(Max. cross-secti

12、onal area): ，连接至接线端子最多根数(maxi. Numberof wires): _;最小导线截面(Min. cross-sectional area): ，连接至接线端子最多根数(min number ofwires):螺纹直径或拧紧力矩 (Screw diameter or Tightening torque): (12)辅助回路(Auxiliary Circuit):额定绝缘电压Ui: 额定冲击耐受电压Uimp: (13)控制回路(Control Circuit):额定绝缘电压Ui: 产品描述(Product Description)3 .系歹U的描述和型号的解释(Desc

13、ription of product series and explanation of model/ type):3.1 本申请单元产品 (Among the model types within this application):1)除下面 a)、b)和c)中的差异(Except for the difference showed in a), b) and c) below) ,内部载流部件的材料，镀层和尺寸是否相同 (Whether different model types within this application areusing the internal current-

14、carrying parts of the same material, coating and dimension):是；口否2)主触头的尺寸、材料、结构和连接方法是否相同(Whether different model types within this application are using the main contacts of the same dimension, material, structure and connection type):是 否3)任何内配手操机构，其材料和物理特性是否相同：(Whether different model types within t

15、his application are using any internal manual operator of thesame material and physical characteristic):是 否4)模压和绝缘材料是否相同(Whether different model types within this application are using the same molding material and isolation material):是 否5)灭弧装置的的工作原理、材料和结构是否相同(Whether different model types within th

16、is application are using the arc control device of the sameoperational principle, material and structure):是 否6)除下面的a)、b)和c)中的差异，过电流脱扣装置的基本结构是否相同(Whether different model typeswithin this application are using the overcurrent trip unit of the same basical structure, except the difference below): 是 否 注

17、:a)接线端尺寸，只要电气间隙和爬电距离不减少(Difference in wire terminals' dimensions isacceptable, as long as electrical clearance and creepage distance are not reduced);b)对于热磁脱扣器，其确定电流额定值的脱扣元件的尺寸和材料(For TMTU, difference indifferent rating trip units' dimensions and sizes is acceptable);c)供脱扣器运行的电流互感器的二次线圈(Diff

18、erence in the secondary coil of the currenttransformer which is for the trip unit operating is acceptable);3.2 系列的描述(对本申请单元不同型号、不同电流等级的异同说明)：(Series description (please elaborate on the sameness and difference among the different typesor different current products):产品描述(Product Description)3.3 型号的解释

19、(Explanation of model/ type):4 .特殊结构说明(如有需要):Description of special structure (if necessary):产品描述（Product Description）5 .产品认证情况（Any approvals before?）:6 .女全件一览表（Safety components/parts list）:序号 Item No.元/部件名称Name of components/parts元件/材料名称Description of Parts/Material型号规格/牌号Type/Model Serial number供

20、应商（生产J ）Supplier（Plant）1底座（板）、外壳Base （board ） or enclosure2主开关兀件Components of main switch3控制器Controll er微处理器Microprocessor电子组件板Electronic board4操作机构Operating mechanism注1:安全件如涉及一个以上的制造商（生产厂），则填在A位的制造商（生产厂）为型式试验样品提供安全件的制造商（生产厂）。注2:本企业声明：安全件如涉及一个以上的制造商（生产厂），型式试验样品所选用制造商（生产厂）提供的安全件与本企业所填写的其他制造商（生产厂）提供的该安全件不存在性能上的差异。Note1: for the above listed safety pa