易福门流量计SI1000基本使用说明

1、易福门流量计SI1000根本使用说明易福门SI1000流量计用于艺康化工“ CF6'自动泡沫系统,主要作用是自动泡沫系统启动后,当流量计检测到流量后,配合压力开关启动增压泵,当流量小于设定值时停止增压泵.易福门SI1000流量计的设定主要包括四个方面：1. 最大流量设定：I c_ -hiiHnnnnnnnMimnrmrmnniPress the Learn/Set button and keep it pressed.The green LEDs on the right and on the left flash, after 5s the LED bar (green) fills

2、 from left to right(release the button as soon as the first LEDs light).The indication goes off briefly.The unit 5toes the current flow as Taximum flow and passes into the operating mode.httingLutton今MODE / lOfIOI LEARN /ENTER= SETFLOW RATEfurn th/ri 'Jisplcivinnnnnnnmnn 匚,丁 N 三 1 E 弓 "E P

3、如下列图：将自动泡沫系统" CF6'处于泡沫清洗状态,常按 LEARN/SET® 5S 10S,此时指示灯变化是先左右两个闪烁,随后从左到右依次闪烁,最后指示灯全部点亮,恢复正常后退出此模式.2. 最小流量设定:Allow the medium to flow through the system at the requiredminimum flow rate or bring to a standstill.LOHI 门口 rinnri 口门口口9HIinnnnnnnnnniimnEFinnniPress the Learn/Set button and kee

4、p it pressed.The green LEDs on the right and on the left flash,after 5s the LED bar (green) fills from left to rightafter a further 5 s the LED bar (gren) fills from right to left (release the button as soon as the first LEDs on the right light).The indication goes off briefly.The unit stores the cu

5、rrent flow as minimum flow and passes into the operating mode.如下列图：将自动泡沫系统" CF6'处于停止状态,常按 LEARN/SE谯10S-15S,此时指示灯变化是先左右两个闪烁,随后从左到右依次闪烁,然后从右到左依次闪烁,最后指示灯恢复正常后退出此模式.3. 恢复出厂设定:M*Press the Learn/Set button and keep it pressed,The green LEDs on the right and on the left flash,after 5s the LED bar

6、(green) fills from left to rightafter a further 5s the LED bar (green) fills from right to left,after a further 5s the LED bar (orange) fills from left to right (release the button as soon as the first orange LEDs light).The indication goes off briefly.All settings are returned to factory setting an

7、d the unit passes into the run mode flow.如下列图：将自动泡沫系统" CF6'处于停止状态,常按 LEARN/SE谯15S 20S,此时指示灯变化是先左右两个闪烁,随后从左到右依次闪烁,然后从右到左依次闪烁,接着桔黄色指示灯从左到右依次闪 烁,最后指示灯全部点亮后,恢复正常后退出此模式.4. 流量计开关临界点的设定:m 之一 .川 Press the Mode/Enter button.HI' '"-,briefly. The current switch point is<'indicated:

8、1 xLED lit: coarse setting, LEDflashes: fine settling.Press the Learn/Set button and keep it pressed.After 5s the switch point is increased* (incremental by pressing briefly or scrolling by holding pressed).Indication:The flashing LED moves from left to right. After LED 9 has been reached the cycle

9、starts again at LED 0. The LED which is constantly lit moves on by one position.*Press the Mode/Enter button briefly (acknowledgement). The indication goes off briefly. The set switch point becomes effective; the unit passes into the operating mode.如下列图：将自动泡沫系统" CF6'处于停止状态,按 MODE/ENTE键一次, 此时有一个指示闪烁,随后按住LEARN/SET!不放,闪烁的指示 灯会依次从左到右跳动,弁带动另一个指示灯一