N安装配置手册

1、N6040安装配置手册一、初始化设置1二、命令行配置RAID42.1建立一个RAID42.2修改时间42.3关闭集合快照42.4缩小根卷42.5添加license42.6配置双机4三、扩大RAID集合，将其它盘加入阵列。4四、配置卷及ISCSI主机映射84.1新键卷84.2配置ISCSI-LUN11创建LUN11创建initiator group12客户端安装initiator13客户端连接N6040134.2.5 MAP LUN建立映射关系13五、主机识别硬盘15硬件环境描述：n6040双控制器，两个磁盘扩展柜，SATA磁盘。A和B控制器各需要在FilterView单独配置。其中硬盘加入和划

2、分部分以举例说明一、初始化设置A控制器：Data ONTAP Release 7.1H2: Fri Nov 11 11:14:38 PST 2005 (IBM)System ID: 0084243431 (N6040b); partner ID: 0084228035 ()System Serial Number: 130240711 (N6040b)System Rev: A0slot 0: System Board Processors: 2 Processor revision: B2 Processor type: 1250 Memory Size: 1022 MBslot 0: FC

3、 Host Adapter 0b 17 Disks: 6127.5GB1 shelf with AT-FCX, 1 shelf with EFHslot 0: FC Host Adapter 0c slot 0: Dual SB1250-Gigabit Ethernet Controller e0a MAC Address: 00:a0:98:03:c1:12 (auto-unknown-down)e0b MAC Address: 00:a0:98:03:c1:13 (auto-unknown-cfg_down)slot 0: NetApp ATA/IDE Adapter 0a (0x0000

4、0000000001f0) 0a.0 249MBPlease enter the new hostname N6040b: Do you want to configure virtual network interfaces? n: yNumber of virtual interfaces to configure? 0 1Name of virtual interface #1 : vif（虚接口名称）Is vif a single s or multi m virtual interface? m sNumber of links for vif? 0 2（虚接口数目）Name of

5、link #1 for vif : e0aName of link #2 for vif : e0bPlease enter the IP address for Network Interface vif : ×. ×. ×. ×Please enter the netmask for Network Interface vif .0: Should virtual interface vif take over a partner virtual interface during failover? n: yThe clustered failove

6、r software is not yet licensed. To enable network failover, you should run the 'license' command for clustered failover.Please enter the partner virtual interface name to be taken over by vif : vifPlease enter media type for vif 100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000) auto: Would you

7、like to continue setup through the web interface? n: Please enter the name or IP address of the default gateway: The administration host is given root access to the filer's/etc files for system administration. To allow /etc root accessTo all NFS clients enter RETURN below.Please enter the name o

8、r IP address of the administration host: What is the TimeZone: Asia/ShanghaiWhere is the filer located? :What language will be used for multi-protocol files (Type ? for list)?:language not setDo you want to run DNS resolver? n: Do you want to run NIS client? n: The initial aggregate currently contai

9、ns 2 disks; you may add moredisks to it later using the "aggr add" command.B控制器Data ONTAP Release 7.1H2: Fri Nov 11 11:14:38 PST 2005 (IBM)System ID: 0084243431 (N6040b); partner ID: 0084228035 ()System Serial Number: 130240711 (N6040b)System Rev: A0slot 0: System Board Processors: 2 Proce

10、ssor revision: B2 Processor type: 1250 Memory Size: 1022 MBslot 0: FC Host Adapter 0b 17 Disks: 6127.5GB1 shelf with AT-FCX, 1 shelf with EFHslot 0: FC Host Adapter 0c slot 0: Dual SB1250-Gigabit Ethernet Controller e0a MAC Address: 00:a0:98:03:c1:12 (auto-unknown-down)e0b MAC Address: 00:a0:98:03:c

11、1:13 (auto-unknown-cfg_down)slot 0: NetApp ATA/IDE Adapter 0a (0x00000000000001f0) 0a.0 249MBPlease enter the new hostname N6040b: Do you want to configure virtual network interfaces? n: yNumber of virtual interfaces to configure? 0 1Name of virtual interface #1 : vif （虚接口名称）Is vif a single s or mul

12、ti m virtual interface? m sNumber of links for vif? 0 2（两个虚接口）Name of link #1 for vif : e0aName of link #2 for vif : e0bPlease enter the IP address for Network Interface vif :×. ×. ×. ×(接口地址)Please enter the netmask for Network Interface vif : Should virtual interfac

13、e vif take over a partner virtual interface during failover? n: yThe clustered failover software is not yet licensed. To enable network failover, you should run the 'license' command for clustered failover.Please enter the partner virtual interface name to be taken over by vif : vifPlease en

14、ter media type for vif 100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000) auto: Would you like to continue setup through the web interface? n: Please enter the name or IP address of the default gateway: The administration host is given root access to the filer's/etc files for system administration.

15、To allow /etc root accessTo all NFS clients enter RETURN below.Please enter the name or IP address of the administration host: What is the TimeZone: Asia/ShanghaiWhere is the filer located? What language will be used for multi-protocol files (Type ? for list)?:language not setDo you want to run DNS

16、resolver? n: Do you want to run NIS client? n: The initial aggregate currently contains 2 disks; you may add moredisks to it later using the "aggr add" command.二、命令行配置raid 2.1建立一个RAIDN6040b>aggr options aggr0 raidtype raid4N6040b>disk zero all spares2.2修改时间N6040b>date 年月日小时分钟2.3关闭

17、集合快照N6040b>snap reserve A aggr0 02.4缩小根卷N6040b> vol size vol0 20G确认完成加盘。2.5添加licenseN6040b>license add XXXXXXX 可选步骤2.6配置双机N6040b>cf enable (需要重启后才生效)三、扩大RAID集合，将其它盘加入阵列。登陆WEB管理http:/* /na_admin/点击FILERVIEWN6040bàAggregatesàManage点击aggr0àAdd disk 添加硬盘到阵列组选择手动选择增加添加硬盘，留出两块盘作为热备（SATA做DP系统强制双热备）四、配置卷及ISCSI主机映射4.1新键卷N6040bàVolumesàAdd4.2配置ISCSI-LUNN6040bàLunsàEnable/Disable4.2.1创建LUNN6040bàLunsàAdd注意空间大小占用不要超过卷的97%4.2.2创建initiator groupN6040bàLuns&#