教程说明成果飞利浦

1、CSS5530B/12_37 CSS5530G/12_96_931 - 1ACTIVE SPK SYSTEMService Service ManualTABLE OF CONTENTSChapterLocation Of PCBA & Versions Variation1-2Technical Specification1-3Safety instruction1-4Software upgrade instruction2Trouble Shooting3Dismantling instructions4Block Diagram5Wiring Diagram6MAIN+BT&LED+K

2、EY PCB(Main unit)7PSU& PCB(Wireless box)8AMP+LED PCB(Subwoofer)9POWER PCB(Subwoofer)10Mechanical Exploded11Revision List12 Copyright 2015 WOOX Innovations limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,

3、mechanical, photocopying, or otherwise without the prior permission of WOOX Innovations. Philips and the Philips shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.Published by KZ_HF1724GB 3140 038 6

4、2930Version 2.01 - 2LOCATION OF PCBAMain UnitWireless BoxSubwooferVERSIONS VARIATION:*M= Module Level Repair*C = Component Level RepairType/VersionsBoard in usedCSS5530BCSS5530G/12_37/12_96_93MAIN+BT&LED+KEY Board (main unit)CCPSU& Board (Wireless Box)CCSUB AMP+LED Board (subwoofer)CCPOWER Board

5、(subwoofer)CCWIRELESS MOUDLELED PCBAMP PCBPOWER PCBPSU& PCBWIRELESS MODULEKEY PCB NFC MODULE MAIN PCBBT&LED PCBWIRELESS MODULE1 - 3Technical SpecicationSubwooferTotal output power: 420W RMS (+/- 0.5 dB, 10% THD)Frequency response: 20 Hz-20 kHz / 3 dBSignal-to-noise ratio: 65 dB (CCIR) / (A-weight

6、ed)Power supply: 220-240 V, 50-60 HzPower supply: 110-127/220-240V, 50/60 Hz(for TW) Power consumption: 60 WStandby power consumption: 0.5 W Impedance: 3 ohmSpeaker drivers: 1 x 165 mm (6.5) woofer Dimensions (WxHxD): 228 x 406 x 265 mmWeight: 5.7 kgInpusitivity: AUX: 500 mV AUDIO IN: 200 mVAudioWir

7、eless box/receiverS/PDIF Digital audio input:Optical:TOSLINKPower supply: 110-240 V, 50-60 Hz Power consumption: 20 WStandby power consumption: 0.5 W Dimensions (W x H x D): 150 x 44.5 x 126 mm;Weight: 0.4 kgBluetoothBluetoothA2DPBluetooth version: 4.1Main unitRemote control batteriesPower supply:1

8、x AAA-R03-1.5 VM(Philips branded AC poweradapter): DYS602-210309W; AS650- 210-AA309Input: 100-240 V, 50/60 Hz 1.5 AStandby power managementWhen the product remains inactive for 15 minutes, it automatically switches to standby or networked standby.The power consumption in standby or networked standby

9、 is less than 0.5W.To deactivate Bluetooth connection, press and hold the Bluetooth button on the remote control.To activate Bluetooth connection, enable Bluetooth connection on your Bluetooth device, or enable Bluetooth connection via the NFC tag (if available).Output: 21V, 3.09AStandby power consu

10、mption: 0.5 W Dimensions (WxHxD): 580 x 51.5 x 98 mmWeight:1.2 kgBuilt-in speakers2 x midrange (90mm/3.5 x 34mm/1.3, 8 ohm)1 x tweeter (25.4mm/1, 8 ohm)Front/rear speakersSpeaker drivers:2 x midrange (63.5 mm/2.5, 10 ohm)1 x tweeter (25.4 mm/1, 8 ohm)Dimensions (WxHxD): 110 x 301 x 110 mmWeight:1.2

11、kg (front)1.3 kg (rear)Cable length: 5 m/each1 - 4Safety InstructionNever place the product or any objects on power cords or on other electrical equipment.If the product is transported in temperatures below 5C, unpack the product and wait until its temperature matches room temperature before connect

12、ing it to the power outlet.Risk of electric shock orBefore you make or change any connections, make sure that all devices are disconnected from the power outlet.Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are s

13、pilt on or into the product, disconnect it from the power outlet immediately. Contact Consumer Care to have the product checked before use.Never place the product and accessoriesParts of this product can beofglass. Handle with care to avoid injury anddamage.Risk of overheating! Never install this pr

14、oduct in aspace. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product.Risk of contamination!near nakedor other heat sources,including direct sunlight.Never insert objects into the ventilatio

15、nslots or other openings on the product. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remainily operable.Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine,or the like.Disconnect the pr

16、oduct from the power outlet before lightning storms.When you disconnect the power cord,Do not mix batteries (old and new or carbon and alkaine, etc.).Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.Remove batteries if they are exhausted or if

17、the remote control is not to be used for a long time.Batteries contain chemical substances, theyalways pull the plug, never the cable.should be disposed of properly.Risk of short circuit orRisk of swallowing batteries! Forand supply ratings, see The product/remote control may contain a coin/button t

18、ype battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within twothe type plate at the back or bottom of the product.Before you connect the product to thepower outlet, e

19、nsure that the power voltage matches the value printed on the back or bottom of the product. Neverhours of ingestion.If youthat a battery has beenconnect the product to the power outlet if the voltage is different.swallowed or placed inside any part of the body, seek immediate medical attention.When

20、 you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children an

21、d contact the manufacturer.Risk of injury or damage to this product! For wall-mountable products, use only the d wall mount bracket. Secure thewall mount to a wall that can support the combined weight of the product and the wall mount. WOOX Innovations bears no responsibility for improper wall mount

22、ing that results in accident, injury or damage.1 - 5Safety InstructionComplianceThis is CLASS II apparatus with double insulation, and no protective earth provided.Care for your productThis product complies with the radio interference requirements of the European CommuHereby, WOOX Innovations, decla

23、res that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.A copy of the EC declaration of Conformity isUse onlycloth to clean the product.Care of the environmentDisposal of your old product and batteryavailable at.Your product is desi

24、gned and manufactured with high quality materials and components, which can be recycled and reused.This symbol on a product means that the product is covered by European Directive 2012/19/EU.This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot b

25、e disposed of with normal household waste.Inform yourself about the local separate collection system for electrical and electronic products and batteries. Follow local rules and never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries hel

26、ps preventnegative consequences for the environment and human health.Removing the disposable batteriesTo remove the disposable batteries, see battery installation section.2 - 1Software upgrade instruction1)Restore factory settinga) In AUX Mode, press buttons on the remote control in sequence to rese

27、t the default settings that has been programmed at the factory. When the factory settings is restored completely, the product automatically switches off and restarts.2)Check software versiona) InARC source, press button on the remote control in sequence within three secondsto check the software vers

28、ion. The software version number is dispayed on the display panel.3) Software Upgrade via USBa) Check for the latest software version on. Search for your mand click on“Software and drivers”.b) Download the software into a USB flash device.1. Unzip the downloaded file if zipped, and make sure that th

29、e unzipped file is named “CSS5530.bin”.2. Put the “CSS5530.bin” file in the root directory of the USB flash drive.c) Connect the USB flash device to the(SERVICE) connector on this product.d) Switch this product toARC source, and switch your TV to thesource.e) Press Mute button two times, Volume + bu

30、tton once and then hold down SOUND button on the remote control in sequence within six seconds.f) Wait until the upgrade is completed. When the upgrade is complete, this product automatically turns off and on again.3 - 13 - 1Trouble Shooting(main unit)CSS5x30 REPAIR CHARTAStandby LEDred light is not

31、 brightBPower Supply No WorkingCDont power ONDEAUX INNo OutputFWireless No OutputGBluetooth No OutputHARCNo OutputIOptical In No OutputJSubwoofer No SoundAll FunctionNo SoundABCDEStandby LEDred liAll Function No SoundAUX INNo OutputPower Supply No workingDont power ONght is not brightOKOKYESNGYESbad

32、Re-insert and fix the cableCheck touch to mainboardCN204 13pin cable ischeck BAs per B RepairCheck POWER IC Voltage +21VCheck JK302 OK or badSee Contents Breplace the bad partcheck DC in 21Vlooseor bad INTNOOKOKYESOKbadNGbadNoNoCheck DCIN JACKCJP101 OK or badCheck BL601 Pin29 Voltage approx +3.8VChe

33、ckR619 IC103And Its Conjoint partsAs per A RepairCheck IC201 I2S pin And Its conjoint partscheck red LED LD602 part fine or badOKreplace the bad partreplace the bad partCheck ACheck I2S outputNoOKOKOKNoNoNoNocheck IC201 PIN98 voltage 0VCheck CN603 And Its Conjoint PartCheck power IC voltage BK5VChec

34、k AMP IC PDN PIN19 Voltage 3.3VCheck AMP IC PDN PINAnd Its conjoint partsCheck BL601 Pin7(TX Check BL601 Pin8(RX)Check IC201 Pin36,37sCheck IC891 L892And Its Conjoint PartReplace the AdaptorAnd Their Conjoint PartOKOKOKOKNoNoCheck power IC voltage BK33Check IC201And Their Conjoint Partscheck IC 201

35、And Its Conjoint PartCheck IC102 FB102L102And Its Conjoint PartCheck AMP IC 13.27PINVoltage VD33Check AMP IC 13.27PINAnd Its conjoint partsOKYesNoCheck IC201 pin40 And Its conjoint partsCheck AMP IC And Its conjoint partsCheck power ON/OFF controlFGHIOptical No OutputWireless No OutputBluetooth No O

36、utputARCNo OutputINTCheck cn203&CN802 No Pin1 approx 5V& +3.3VNoINTCheck JK301 INT OR NOCheck FB201&FB202 And Its Conjoint PartsCheck BT601 PIN29Voltage approx +3.8VCheck IC103And Its Conjoint PartsCheck JK702 INT or NoREPAIR okChange this jackOKOKOKOKbadNoOPNoCheck BL601 Pin7(TX Check IC201 Pin36,3

37、7Check IC703 FB706And Its Conjoint PartsCheck JK301 pin1 approx +3.3V yes or NoCheck And Repair L302 And Its Conjoint PartsCheck CN203&CN802 INT or NoCheck IC701 Pin53/71/78+1.8V Yes or Noreplace the bad partCheck BL601 Pin8(RX)And Their Conjoint PartsOKOKOKOKNoOPbadCheck IC201And Their Conjoint Par

38、tsCheck FB704And Its Conjoint PartsCheck IC201 PIN99(SDA) Check IC201 PIN98(SCL)Check IC201 And Its Conjoint PartsCheck IC701 Pin74+3.3V Yes or NoCheck R301 C301replace the bad partOKOKCheck IC201 Pin17And Its Conjoint PartsCheck IC701 And Its Conjoint Parts3 - 23 - 2Trouble Shooting(subwoofer)Speak

39、er No OutputAll Function no WorkingCheck module if okCheck +34.5V if okCheck power pcb F900 if OK or badReinsert and fix the Fuse F900Change9pinCheck cable if OKwireless moduleCheck power D916,D918,IC900, IC902, Q902,Q906,Q907,T903Transformer and their conjoint partCheck BK3.3V, +12VIf have outputCh

40、eck power pcbC940, L905,Q904,Q903,D919,IC903,T901,T902Transformer and their conjoint partCheck wireless module if okCheck L202, L203 L205,Q203Check main pcb and conjoint part.Check IC200 and IC201Cant receiver signal No output,LED no lightCheck LED and their part listCheck receiver module if okCheck

41、 wireles module and fix the moduleCheckChange transmitter module4- 1Note:In some service positions the components or copper patterns of on4 - 1Dismantling of the KEY Boards1) Loosen 4 screws “I” on the top of KEY board as shown in figure 9.may risk touching itsneighbouring pc boards or metallic part

42、s. To prevent such short-circuit use a piece of hard paper or other insulating material between them.IDismantling Instructions(Main Unit)Dismantling of the outer cover assembly1) Loosen 5 screws “ A ” and 10 screws “B” to remove the outer cover as shown in figure 1 & 2.Figure 9SERVICE POSITIONS(Main

43、 Unit)Servie AAFigure 1BFigure 2Dismantling of the BT+LED Board1) Loosen 3 screws “ C ” as shown in figure 3 to pull the whole PCB Assy out from the top cover.2) Loosen 2 screws “ D ” on the top of BT+LED board as shown in figure 4.Dismantling Instructions(Wireless Box)Dismantling of the outer cover

44、 assembly1) Loosen 3 screws “ J ” to remove the bottom cover as shown in figure 10.DCFigure 3Figure 4JDismantling of the MAIN Board1) Loosen 6 screws “ E ” on the top of Main board as shown in figure 5.2) Loosen 1 screw “ F ” &1 screw “G” &1 screw “H” at the bracket as shown in figure 6 & 7 & 8.FFig

45、ure 10Dismantling of the PSU& Board1) Loosen 3 screws “ K ”on the top of PSU& Board as shown in figure 11.EFigure 5Figure 6HKGFigure 7Figure 8Figure 114 - 24 - 2Dismantling Instructions(SUBWOOFER)Dismantling of Back panel assembly1) Loosen 8 screws “L” to remove the back panel as shown in figu

46、re 12.LFigure 12Dismantling of AMP+LED Boards1) Loosen 4 screws “M” on the top of AMP Boards as shown in figure 13.2) Loosen 2 screws “O” on the top of LED Boards as shown in figure 14.MoFigure 14Figure 13Dismantling of POWER Boards1) Loosen 4 screws “P” on the top of Power Boards as shown in figure

47、 15.PFigure 155 - 15 - 1Block Diagram_RX/TX/I2C/INT/RSTEP92A3E-CECRepeaterInputSPIDF-ARC18.432MHz CRYSTALMPEG DTS MP3/WMADecodeSPIDF-INOPTICALBT Internal AntennaNFCNFC-G1BT controlUART/ResetL10 OHM 20WTHD 10%I2S/MCLKBT SPIDF-OUTPBTLAB1510GNO APTXTAS5731M10 OHM 20WTHD 10%PWR AMPI2C / RST /PWDNTweeter

48、+-8OHM30W(10%)DATA _Sub/SL/SRBuff er 74HC04MP3-INI2SR10 OHM 20WTHD 10%PBTLWirelessInternal AntennaTAS5731M10 OHM 20WTHD 10%PWR AMPWireless moduleI2C/IRQ/ResetSMSC DWHP83for5.1Avnera Moudlefor 3.1Tweeter+-8OHM30W(10%)C8OHM 20WTHD 10%CRYSTAL 27MHzPBTLTAS5731MIRIR8OHM 20WTHD 10%12CPWR AMPReset ICLM809T

49、weeter+8OHM30W(10%)-5 Digital LED DisplayInternal Antenna4Key controlRXSW-TACKLRCKTAS5538ABCK3OHMFor MT8307 DebugSubwooferSDOUT220W(10%)8307 DebugVOLUMEMCLKGNDSDRAMLED-WEM638165TS-6G+34VDE-PWRLDO LM317KNAND FlashWireless PSUPWR/STBYEN25F16+3.3Vwireless subwoofer boxAUX_INMT8307-OXESurround RXWireless module SMSC DWHP83I2SMCLKSub RXWireless module Avnera Moudlefor 3.1