实验 配置VLAN间路由

1、实验六 配置VLAN间路由实验目标l 深入了解交换机VLAN的配置l 熟悉VLAN Trunk的配置l 熟悉不同VLAN之间路由的配置实验内容l 配置VLAN Trunkl 配置VTPl 配置VLAN 间路由实验步骤20.1按照下面的指示，连接网络设备30.130.220.2F0/0F0/0F0/1SwitchBSwitchAF0/2F0/2F0/7VLAN10F0/7VLAN10TrunkF0/8VLAN20F0/8VLAN20Step1：主机的准备并验证连通性a. 连接SwitchA端口0/7的主机：IP address 192.168.100.2SDefault gateway 192.

2、168.100.1b. 连接SwitchA端口0/8的主机IP address 192.168.110.2Default gateway 192.168.110.1c. 连接SwitchB端口0/7的主机：IP address 192.168.100.3Default gateway 192.168.100.1d. 连接SwitchB端口0/8的主机IP address 192.168.110.3Default gateway 192.168.110.1e. 用ping命令测试连通性Step2：配置并命名VLAN Switch_A#vlan databaseSwitch_A(vlan)#vla

3、n 10 name SalesSwitch_A(vlan)#vlan 20 name SupportSwitch_A(vlan)#exitStep3：分配成员端口给各个VLAN分配两个交换机上的端口0/7给VLAN 10, 0/8给VLAN 10Switch_A#configure terminalSwitch_A(config)#interface fastethernet 0/7Switch_A(config-if)#switchport mode accessSwitch_A(config-if)#switchport access vlan 10Switch_A(config-if)#

4、interface fastethernet 0/8Switch_A(config-if)#switchport mode accessSwitch_A(config-if)#switchport access vlan 20Switch_B#configure terminalSwitch_B(config)#interface fastethernet 0/7Switch_B(config-if)#switchport mode accessSwitch_B(config-if)#switchport access vlan 10Switch_B(config-if)#interface

5、fastethernet 0/8Switch_B(config-if)#switchport mode accessSwitch_B(config-if)#switchport access vlan 20Switch_B(config-if)#end分配SwitchA上的端口0/2给VLAN 10, SwitchB的端口0/2给VLAN 20Switch_A#configure terminalSwitch_A(config)#interface fastethernet 0/2Switch_A(config-if)#switchport mode accessSwitch_A(config

6、-if)#switchport access vlan 10Switch_B#configure terminalSwitch_B(config-if)#interface fastethernet 0/2Switch_B(config-if)#switchport mode accessSwitch_B(config-if)#switchport access vlan 20Switch_B(config-if)#endStep4：验证配置结果在特权模式下输入 show vlanStep5：配置Trunk 在交换机 A,B 的 Fast Ethernet 0/1 配置如下命令：Switch_

7、A(config)#interface fastethernet0/1Switch_A(config-if)#switchport mode trunkSwitch_A(config-if)#endSwitch_B(config)#interface fastethernet0/1Switch_B(config-if)#switchport mode trunkSwitch_B(config-if)#endStep6：配置路由使用命令配置 Fast Ethernet 接口，例如：Router_A(config)#interface fastethernet 0/0Router_A(config-if)#00Router_A(config-if)#no shutdownRouter_A(config)#interface fa