3D打印机Z601安装流程英文版-中性

1、1 Z601 ASSEMBLY PROCESSNOTES： 1.Please ensure that the packaging is intact before signing. 2. After unpacking, please confirm the goods and quantity is consistent with enclosed packing list. 3. If any question, please contact our customer service immediately.2Components3Plastic components4Lead-screw

2、 and feed rodUsed to install cradle5Post-installation picture6NO: 1M8 nutM8 locknutM8 shim400MM7NO: 2Install as shown belowPost-installIn the center No lockSymmetry on both side No lock2-M8*290MM lead-screw8NO: 3Install as shown belowIn the center No lock2-M8*290MM lead-screw9NO: 4Install as shown b

3、elowIn the center （2-M8*370MM lead-screw）10NO: 5Lock frame angle11NO: 6Install as shown below4-M8*370MM lead-screw12NO: 7Install as shown belowInsert 2 M3 nutsUsed to fix Z axis feed rod（no lock）M3*20 screw + shim13NO: 8Install as shown belowM8*400 lead-screw14NO: 9Put the components on No.6, No.7 a

4、nd No.8 together as shown below 15NO: 10Put the components on No.5 and No.9 together as shown below, and lock it.16NO: 11Install M8*400 lead screw as shown belowM8*400 lead-screwNo lock. Calibrate after the top is installed 17NO: 12Install bearing as shown belowComponents:（M4*10 screw) bearing, alum

5、inum sheetNo lock, need to calibrate later18NO: 13 WARNING: Avoid the small steel balls slipping out from bearing As shown below400mm feed rod19NO: 14123ATTENTION: Follow the directions carefullyInstall as shown: Lock those 12 M4 screw and make sure aluminum sheet can move freely.20NO: 15Install Y a

6、xis motor and synchronizing wheel as shown belowM3 jackscrew 2PCSY axis motor3PCS M3*10 screw+ shim21NO: 16Red line connect blue lineBlack line connect green lineZ axis motor22NO: 17Install belt as shown belowM3*10 screw 4PCS23NO: 18Install thermistor as shown belowBakelitePyrocottonThermistorinsert

7、 the thermistor according to the direction of the trench and then sealed with high-temp sealantTrench24NO: 19Install heating plate and bakelite as shown below25NO: 20Install hot bed as shown belowHeating plateBakeliteAluminum sheetLocknutM3*20Fix the three boards on four corners using M3 screwSpring

8、26NO: 21Install extruder platform as shown belowNo lock. Need to calibrate laterM4*16 screw27NO: 22Install as shown belowComponents：623 bearing、M3*16 grub screw、M3 locknut、spring seatMake sure the bearing can move freely28NO: 23Install extruder as shown below12345shimLock it using jackscrew M3*12 sc

9、rewM3*20 screw29NO: 24Install as shown belowM3*10 screw30NO: 25Insert 8 M3 nuts as seen below, used jackscrew on step3231NO: 26Put the components on step 22 together as shown below32NO: 27Install as shown belowpush spring in soleplate, and lock it with screw33NO: 28Post-installation pictureThe crew

10、should be completely inserted into the soleplate 34NO: 29Install the coupling-dek as shown belowCoupling-dek can not be too far from the motor35NO: 30Install as shown belowShim36NO: 31Install as shown belowInstall X axis motor 3PCS M3*10 screw+ shim37NO: 32Install as shown belowM3 jackscrewFix X axi

11、s feed rod with jackscrew38NO: 33Install as shown belowLock these 12 M4 screw and make sure extruder platform can move freely.39NO: 34Install extruder and fan as shown belowExtruder motorM3*16 screw40NO: 35Install X axis belt as shown below41NO: 36Install X axis belt as shown belowM3*25 screw42NO: 3

12、7Install extruder as belowPush the extruder upwards43NO: 38Install as belowLock motor:M3*25 screw+shimLock extruder: M3*20 screw+shim44NO: 39Post-installation picture45NO:40Install limit switchM3*16+locknut46NO: 41Install X axis limit switch as belowRight hereM3*16+M3 nut47NO: 42Install Y axis limit switch as below48NO: 43Install Z axis limit switch as below49NO: 44Install as below50NO: 45Connect lines as shown below51NO: 46WARNING: PCB can not have contact with metal portion that may cause short circuit52NO: 47Post-installation picture53NO: 48Post-installation pict