注塑方面英语术语（范本）

1、注塑方面英语术语压铸                die-cast压炼                  injection铸件            

2、60;     casting/cast/founding起泡/气泡        bubble/blister/air bubble缺料                   shorshots/undershot浇不足/铸     underfounding多料

3、60;                   superfluities/superfluous material(alloy）顶针痕               ejector (pins) mark花纹      &#

4、160;             flow mark/flow line冷纹                     cold mark/cold streak油纹         

5、0;           oil streak走水纹                 splash mark银纹                   

6、   silver streaks霜纹                      splay mark夹水纹                  silver streaks/flow line/wel

7、d line扣模/粘模            sprue sticking砂眼/气眼            air hole（塑胶件)弯曲/变形          warping/warpage变形       

8、0;               deformation扭曲                       twist翅曲          

9、             warp/warped材料错误               using wrong plastic material凸痕                &

10、#160;      convex mark凹位/凹陷             sink mark/dent mark披锋                       flashing批损  

11、;                     paremark/cut mark批凹                       pare off锉纹  

12、0;                    trimmark/file-mark锉损                       excessive trim mark黑点/黑纹 

13、            black spots/black streak发白                       white mark烧焦          &#

14、160;            burn marks刮花/刮痕             scratch mark擦痕/擦伤             rubmark/brush-burn裂缝     &

15、#160;                 cracking裂纹                       craking line碰损       

16、;                 stress mark起皮                        chip错位（合模线)  part line misaling ment孔位尺寸改变

17、60;     dimension various哑色                        dull color表面变光滑（喷油面）     glossy finishing表面        

18、60;                sruface/outside镶件                         insert/insert word缩水/收缩   

19、60;           sink mark/shrinkage/shrink mark偏差                        color deviation色粉        

20、;                colourment颜色                        colour/color零件污糟       

21、;        dirty mark on part顶白                        stress mark/ejector mark屈曲            

22、;            bent夹模线移位           part line misalignment胶件料厚不均       uneven wall thickness水口料            &

23、#160;      degraded material凹印                        sink mark擦花                

24、;        abrasion mark混色                        contamination mark热点不良             &#

25、160;  poor heat sticking定位圈                   locating ring唧嘴                       sprue bush&

26、#160; (浇口套）A板                        A plate (定模板）B板                      &

27、#160; B plate（动模板)方铁                       spacer block (垫铁)底板                     &#

28、160; bottom clamp plate（动模底板）面板                       top clamp plate（定模底板)顶针                   

29、;   ejector pin（顶杆)直边钉                  guide pin （导柱)托司                      shoulder guide bush(导套

30、）直司                     straight guide bush（导柱)回针                     return pin（回程杆)细水口边钉 

31、0;      support pin(副导柱)蓝弹簧                 blue spring（回程弹簧)水口推板             runner stripper plate（卸流道板）中边钉    

32、60;            ejector guide pin (顶板导柱）顶针板                 ejector retainer plate（顶杆固定板)顶针底板            

33、ejector plate（顶杆垫板)撑头                      support pollar(支撑柱)垃圾钉                  stop pin （限位钉）呵  

34、                         core (后模肉内镶件）后模肉                  back mold body(后模镶件）前模肉  &

35、#160;                cavity（前模镶件）扣鸡                       P-lock     blister 起泡blooming 起霜blow

36、hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽gr