模具设计DFM模板.-文档资料

1、1 11FS0000F FS0000F DFM ReportDFM Engineer：LIMINApproved: Date：2014/02/26DFM Design For ManufactureProject name:2 22Mould No.FS0000ECustomer NameUKAGCustomer mould No.请客人提供Part No.Screen Side FrameCavities1+1MaterialPC/ABS BAYER T65XFSize for 1 part 182.7X126.9X35Inch/mmmm产品信息 Product Information3 3

2、3开 模 客 供 资料 information to be provided by customer 序序号资料名称资料名称NameName内内 容容DescriptionDescription收到日期收到日期Received dateReceived date备注备注remarksremarks1 胶 料 (resin)PC/ABS BAYER T65XF2014.02.25 2缩 水 率(hrinkage)请客人提供我们选定为0.005，请客人确认或提供3啤机吨位(Press tonnage)请客人提供啤机的相关信息4设计标准customer tooling standard请客人提供 5

3、胶料特性resin date sheet请客人提供 开模时需要收到的客供资料4 44上下模分析 CAV/CORCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NGcavity sidecore side5 55进浇口建议 Gate Advice（方案一）冷流道，两点潜水入胶170mm冷流道，潜水入胶。优点：不需热流道板。缺点：流道长，注塑压力大。模具排位，模胚尺寸为55656 66进浇口建议 Gate Advice（方案二）（推荐）Customer comment. (p

4、lease give your approval and comments)DateApproval by:RemarkOK or NGMoldmaster 1 open nozzle HRM / Sub GateHot SprueSub Gate由于产品较大，同时根据排位需要，我们建议客人每个产品用一个热转冷流道，两点潜水。（请客人确认热嘴的型号并确认是否需要订购接线盒，并提供具体品牌及型号，接线方式。）同时，请客人确认另一个产品是否为完全镜像关系。请市场考虑增加热嘴报价。热嘴转冷流道潜水入胶。优点：流道短，注塑压力小，产品填充好。缺点：需要热流道板，模具成本相应增加。模具排位，模胚尺寸为5

5、5657 77Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG结构分析 Structure analysisStructureQuantitySlide1Lifter0Collapasible core/Core slider 01CCC-C见下页8 88Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG结构分析 Structure analy

6、sisCore sideST1=8ST2=208SECTION C-C自制定位零件，底部加弹弓9 99Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG镶件分析 Insert analysisCavity Insert做浮动镶件，避免产品粘前模10101010Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG镶件分析 Insert analysi

7、sCore Insert下模三个镶件，每个镶件上下两支扁顶针111111Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG顶出建议 Eject AdviceCore side 顶针EJECTOR PINSTRAIGHT BARSTRIPPER BAR121212分型线分析 PL analysisCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG行

8、位分型线需移到此处，与前模做3度的插穿角131313分型线分析 PL analysisCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG此面插穿角不够，需修到35度两处一处为了更好的封胶，此处的插穿距离尽可能修到2.5MM以上141414分型线分析 PL analysisCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG为简化加工及分型，指示处减

9、胶0.03MM，出后模151515擦穿位置分析 Shut off positionCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG此面插穿角不够，需修到3度161616擦穿位置分析 Shut off positionCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG此面插穿角不够，需修到3度171717产品出模分析 Product Draft

10、analysisCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NGDraft analysisDraft OK181818产品料厚分析 Product Thickness analysisCustomer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG产品胶料厚度均匀191919产品光洁度标准NO Texture请提供光洁度标准Customer comment

11、. (please give your approval and comments)DateApproval by:RemarkOK or NG2020201、版本号我司做镶针，相关的字体我司默认为晒字，深0.2MM，凸字。日期镶件（年月一起）Engraving ( Others )Customer comment. (please give your approval and comments)DateApproval by:RemarkOK or NG212121模具排位 Mould overall dimensionsMold overall layoutEJ SIDE PLAN VIEW550650模胚已超报价（4045），请客人确认是否合适啤机，同时，市场考虑是否增加报价22222222备注Remark：烦请贵司在我司提供的开模方案上每页做明确回复（同意或不同意），如未作明确回复的部分，我司将视为默认我司方案，我司将按此方案进行后续工作。Please reply