Brocade7800FCIP配置手册

1、Brocade7800 FCIP配置手册目录一、环境1二、清除GE口原有信息2三、配置GE口类型3四、创建ge0与ge1口IP3五、创建IP路由3六、创建FCIP隧道4七、添加Circuit（电路）5八、配置传输压缩5九、建立lsan zone6十、测试数据复制7一、 环境BJSC-7800-01BJSC-7800-027800-01RJ45RJ45FCFC7800-02RJ45RJ45FCFC7800-01RJ4510.0.100.1RJ4510.0.10.17800-02RJ4510.0.100.2RJ4510.0.10.2二、 清除GE口原有信息BJSC-7800-02:admin po

2、rtshow fcipcircuit all 显示电路信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 InProg -s 1m27s 0.00 0.00 4 20/100 0 16 1 ge1 InProg -s 18m14s 0.00 0.00 4 30/90 0- Flags: circuit: s=sack有2条电路，分别是16 0与16 1BJSC-7800-02:admin portcfgdefault ge0直接清除ge0口信息失败Circuit Configur

3、ation exists using this GE port.BJSC-7800-02:admin portcfg fcipcircuit 16 delete 0需要先删除电路Operation SucceededBJSC-7800-02:admin portcfgdefault ge0清除ge0口信息成功Operation SucceededBJSC-7800-02:admin portcfgdefault ge1同上Circuit Configuration exists using this GE port.BJSC-7800-02:admin portcfg fcipcircuit

4、16 delete 1同上Operation SucceededBJSC-7800-02:admin portcfgdefault ge1同上Operation SucceededBJSC-7800-02:adminportcfg fciptunnel 16 delete删除隧道shwitchshow显示GE口结果 ge0 cu 1G Online FCIP Copper ge1 cu 1G Online FCIP Copper ge2 id 1G No_Light FCIP ge3 - 1G No_Module FCIP ge4 - 1G No_Module FCIP ge5 - 1G No

5、_Module FCIPge0电口ge1电口光口光口Ge2光口Ge3光口Ge4光口Ge5光口当上面2个电口被使用后，下面的前2个光口将不能使用。三、 配置GE口类型BJSC-7800-01:admin portcfggemediatype Usage: portcfggemediatype GbE_port optical 光| copper电 BJSC-7800-01:admin BJSC-7800-01:admin 例如：sw67:adminportcfggemediatype GE0 optical四、 创建ge0与ge1口IPBJSC-7800-01:adminportcfg ipif

6、 ge0 create 10.0.100.1 255.255.255.0 1500BJSC-7800-01:admin portcfg ipif ge1 create 10.0.10.1 255.255.255.0 1500BJSC-7800-01:admin portshow ipif all 显示GE口IPPort: ge0Interface IPv4 Address NetMask Effective MTU Flags- 0 10.0.100.1 255.255.255.0 1500 U R M Port: ge1Interface IPv4 Address NetMask Effec

7、tive MTU Flags- 0 10.0.10.1 255.255.255.0 1500 U R M Flags: U=Up B=Broadcast D=Debug L=Loopback P=Point2Point R=Running N=NoArp PR=Promisc M=Multicast S=StaticArp LU=LinkUpBJSC-7800-01:admin对端BJSC-7800-02配置IP为GE0 10.0.100.2 GE1 10.0.10.2五、 创建IP路由测试环境直连方式可以ping通对端，因此配置路由步骤可先忽略。实际实施时不可省略此步。BJSC-7800-0

8、1:admin portcmd -ping ge0 -s 10.0.100.1 -d 10.0.100.2Pinging 10.0.100.2 from ip interface 10.0.100.1 on 0/ge0 with 64 bytes of dataReply from 10.0.100.2: bytes=64 rtt=2ms ttl=20Reply from 10.0.100.2: bytes=64 rtt=0ms ttl=20Reply from 10.0.100.2: bytes=64 rtt=0ms ttl=20Reply from 10.0.100.2: bytes=64

9、 rtt=2ms ttl=20Ping Statistics for 10.0.100.2: Packets: Sent = 4, Received = 4, Loss = 0 ( 0 percent loss) Min RTT = 0ms, Max RTT = 2ms Average = 1msBJSC-7800-01:admin六、 创建FCIP隧道在第16VE口创建FCIP隧道(先写远端IP再写本端IP,后面的数字单位是K)，两边都要创建BJSC-7800-01:admin portcfg fciptunnel 16 create 10.0.100.2 10.0.100.1 -b 500

10、00 -B 100000Operation Succeeded当仅仅本端建立好后，状态为InProgBJSC-7800-01:admin portshow fciptunnel all 显示隧道信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 - InProg - 0s 0.00 0.00 0 - - Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FICON T=TPerf circuit: s=sackBJSC-7

11、800-01:admin portshow fcipcircuit all 显示电路信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 InProg -s 0s 0.00 0.00 0 50/100 0- Flags: circuit: s=sack当对端也建立好隧道后，状态为UpBJSC-7800-01:admin portshow fciptunnel all- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCn

12、t CommRt Met- 16 - Up - 3m40s 0.10 0.01 1 - - Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FICON T=TPerf circuit: s=sackBJSC-7800-01:admin portshow fcipcircuit all- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 Up -s 3m49s 0.07 0.01 1 50/100 0- Flags:

13、 circuit: s=sackBJSC-7800-01:admin创建好隧道后，0电路也就存在了，并且已经存在于16隧道中。下面要添加1电路到16隧道中。七、 添加Circuit（电路）将Circuit（电路）放到16隧道,编号为1。BJSC-7800-01:admin portcfg fcipcircuit 16 create 1 10.0.10.2 10.0.10.1 -b 50000 -B 100000Operation SucceededBJSC-7800-01:admin两边都要操作添加，第一个IP为目标，第二个IP为本地BJSC-7800-01:admin portshow fc

14、ipcircuit all - Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 Up -s 22m22s 0.02 0.01 2 50/100 0 16 1 ge1 Up -s 10s 0.00 0.00 1 50/100 0- Flags: circuit: s=sackBJSC-7800-01:admin八、 配置传输压缩两边都要改, 建议使用中等压缩比，数字表示为2,高压缩比是3，不建议3.也不建议1.BJSC-7800-01:admin portcfg fciptunnel

15、16 modify -c 2九、 建立lsan zone两边都要建立BJSC-7800-01:admin zonecreate lsan_zone,50:06:0e:80:04:29:3f:12;50:06:0e:80:04:29:3f:32Zone成员的wwn来自两台7800所接的存储78001为4 4 010400 id N2 Online FC F-Port 50:06:0e:80:04:29:3f:1278002为4 4 010400 id N2 Online FC F-Port 50:06:0e:80:14:38:cc:11BJSC-7800-01:admin cfgcreate l

16、san_cfg,lsan_zoneBJSC-7800-01:admin cfgenable lsan_cfgBJSC-7800-01:admin cfgshowDefined configuration: cfg: lsan_cfg lsan_zonezone: lsan_zone 50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11Effective configuration: cfg: lsan_cfg zone: lsan_zone 50:06:0e:80:04:29:3f:12 50:06:0e:80:14:38:cc:11BJSC-780

17、0-01:admin添加其他存储端口到lsan_zoneBJSC-7800-01:admin zoneadd lsan_zone,50:06:0e:80:04:29:3f:32;50:06:0e:80:14:38:cc:31cfgdisablecfgenableBJSC-7800-01:admin cfgshowDefined configuration: cfg: lsan_cfg lsan_zone zone: lsan_zone 50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11; 50:06:0e:80:04:29:3f:32; 50:06

18、:0e:80:14:38:cc:31Effective configuration: cfg: lsan_cfg zone: lsan_zone 50:06:0e:80:04:29:3f:12 50:06:0e:80:14:38:cc:11 50:06:0e:80:04:29:3f:32 50:06:0e:80:14:38:cc:31BJSC-7800-01:admin十、 测试数据复制HDS工程师在USP存储配置界面上可以看到2条连路已经连通。新建2个LUN并作数据复制。（截图略）可以看到数据传输信息和压缩比BJSC-7800-01:admin portshow fciptunnel all

19、 -p-Tunnel ID: 16 Tunnel Description: Admin Status: Enabled Oper Status: Up Compression: On (Moderate) Fastwrite: Off Tape Acceleration: Off TPerf Option: Off IPSec: Disabled Remote WWN: Not Configured Local WWN: 10:00:00:05:33:2d:47:ac Peer WWN: 10:00:00:05:33:31:60:fc Circuit Count: 2 Flags: 0x00000000 FICON: Off Oper Status: Up Flow Ctrl State: Off Connected Count: