基于FPGA数字秒表设计

1、-目录1.秒表设计要求12.设计思路12.1功能模块12.1.1分频器12.1.2计数器12.1.3数据锁存器12.1.4控制器12.1.5扫描显示的控制电路22.1.6显示电路32.1.7按键消抖电路33.电路实现44.程序仿真104.1分频器104.1.1计数器电路综合114.1.2计数器电路仿真114.2同步计数器134.2.1计数器实现134.2.2计数器仿真154.2.3同步计数器电路综合174.3按键消抖电路184.3.1按键消抖电路实现184.3.2按键消抖电路仿真184.3.3按键消抖电路综合204.4八段译码器204.4.1八段译码器实现204.4.2八段译码器仿真214.4

2、.3八段译码器电路综合224.5控制器234.5.1控制器234.5.1控制器仿真244.5.3控制器电路综合255.2View Technology Schematic ：265.3管脚锁定：276.实验结论27. z-1.秒表设计要求（1） 秒表的计时围为00：00：00 59：59：99。（2） 两个按钮开关Start/Stop和Split/Reset，控制秒表的启动、停顿、分段和复位：在秒表已经被复位的情况下，按下“Start/Stop键，秒表开场计时。在秒表正常运行的情况下，如果按下“Start/Stop键，则秒表暂停计时；再次按下该键，秒表继续计时。在秒表正常运行的情况下，如果按下

3、“Split/Reset键，显示停顿在按键时的时间，但秒表仍然在计时；再次按下该键，秒表恢复正常显示。在秒表暂停计时的情况下，按下“Split/Reset键，秒表复位归零。2.设计思路2.1功能模块2.1.1分频器对晶体振荡器产生的时钟信号进展分频，产生时间基准信号2.1.2计数器对时间基准脉冲进展计数，完成计时功能2.1.3数据锁存器锁存数据使显示保持暂停2.1.4控制器通过产生锁存器的使能信号来控制计数器的运行、停顿以及复位设计分析：2.1.5扫描显示的控制电路 包括扫描计数器、数据选择器和7段译码器，控制8个数码管以扫描方式显 示计时结果，原理图如下：实验电路板上的按键2.1.6显示电路

4、2.1.7按键消抖电路消除按键输入信号抖动的影响，输出单脉冲实验板上的数码管为共阳LED数码管按键按下时，FPGA的输入为低电平；松开按键时，FPGA的输入为高电平但是在按下按键和松开按键的瞬间会出现抖动现象2.2电路框图3.电路实现- pany: - Engineer: - - Create Date: 09:08:39 03/12/2021 - Design Name: - Module Name: stopwatch_1 - Behavioral - Project Name: - Target Devices: - Tool versions: - Description: - Dep

5、endencies: - Revision: - Revision 0.01 - File Created- Additional ments: -library IEEE;use IEEE.STD_LOGIC_1164.ALL;use IEEE.STD_LOGIC_ARITH.ALL;use IEEE.STD_LOGIC_UNSIGNED.ALL;- Unment the following library declaration if instantiating- any *ilin* primitives in this code.-library UNISIM;-use UNISIM.

6、Vponents.all;entity stopwatch_1 isPort (Clk : in STD_LOGIC;start_stop : in STD_LOGIC;split_reset : in STD_LOGIC;ncs : out STD_LOGIC;s : out STD_LOGIC_VECTOR(2 downto 0);seg : out STD_LOGIC_VECTOR (7 downto 0);end stopwatch_1;architecture Behavioral of stopwatch_1 issignal k1,k2,k3,k4: STD_LOGIC;sign

7、alt_1,t_2 : STD_LOGIC_VECTOR(1 downto 0);signal start_stop_out,split_reset_out: STD_LOGIC;signal count: STD_LOGIC_VECTOR(15 downto 0):=(others=>'0');signal clk_1k: STD_LOGIC;signal z0,z1,z2,z3,z4,z5,z6,q1,q2,q3,q4,q5,q6 : STD_LOGIC_VECTOR(3 downto 0):=(others=>'0');signal count

8、_2: STD_LOGIC_VECTOR(2 downto 0 ):=(others=>'0');signal in_7: STD_LOGIC_VECTOR(3 downto 0);signal sreg: STD_LOGIC_VECTOR(2 downto 0):="111"signal sne*t: STD_LOGIC_VECTOR(2 downto 0);Begin-为三八译码器置入使能信号 ncs <= '0'-分频电路process(clk)beginif rising_edge(clk) thenif count =

9、47999 thencount <=(others=>'0');elsecount <= count+1;end if;end if;end process;clk_1k <= count(15);-同步计数电路process(clk_1k,sreg(2)beginif rising_edge(clk_1k) thenif sreg(2) = '1' then z0<=(others=>'0');z1<=(others=>'0');z2<=(others=>'0&

10、#39;);z3<=(others=>'0');z4<=(others=>'0');z5<=(others=>'0');z6<=(others=>'0');elsif sreg(1) = '1' thenz0 <= z0+1;if z0 = 9 thenz0 <=(others=>'0');z1 <= z1+1;if z1 = 9 thenz1 <=(others=>'0');z2 <= z2+

11、1;if z2 = 9 thenz2 <=(others=>'0');z3 <= z3+1;if z3 = 9 thenz3 <= (others=>'0');z4 <= z4+1;if z4 = 5 thenz4 <= (others=>'0');z5 <= z5+1;if z5 = 9 thenz5 <= (others=>'0');z6 <= z6+1;if z6 = 5 thenz6 <= (others=>'0');end

12、 if;end if;end if;end if;end if;end if;end if;end if;end if;end process;-扫描计数器process(clk_1k)beginif rising_edge(clk_1k) thencount_2 <= count_2+1;end if;end process;s <= count_2;-锁存器process(sreg(0),z1,z2,z3,z4,z5,z6)beginif sreg(0) = '1' thenq1 <= z1;q2 <= z2;q3 <= z3;q4 <=

13、 z4;q5 <= z5;q6 <= z6;end if;end process;-process(count_2,q1,q2,q3,q4,q5,q6)begincase count_2 iswhen "000" => in_7 <= q1;when "001" => in_7 <= q2;when "011" => in_7 <= q3;when "100" => in_7 <= q4;when "110" => in_7 &l

14、t;= q5;when "111" => in_7 <= q6;when others => in_7 <= "1111" end case;end process;-八段译码器process(in_7)begincase in_7 iswhen "0000" => seg <="00000011"when "0001" => seg <="10011111"when "0010" => seg <

15、;="00100101"when "0011" => seg <="00001101"when "0100" => seg <="10011001"when "0101" => seg <="01001001"when "0110" => seg <="01000001"when "0111" => seg <="0001111

16、1"when "1000" => seg <="00000001"when "1001" => seg <="00001001"when others => seg <="11111101"end case;end process;-按键去抖电路process(clk_1k,start_stop)beginif clk_1k'event and clk_1k='0' thenift_1 = 3 thenk1 <= 

17、9;1'elsek1 <= '0't_1 <=t_1+1;end if;k2 <= k1;end if;if start_stop = '0' thent_1 <= "00"end if;end process;start_stop_out <= not k1 and k2; process(clk_1k,split_reset)beginif clk_1k'event and clk_1k='0' thenift_2 = 3 thenk3 <= '1'els

18、ek3 <= '0't_2 <=t_2+1;end if;k4 <= k3;end if;if split_reset = '0' thent_2 <= "00"end if;end process;split_reset_out <= not k3 and k4;-控制器process(clk_1k,start_stop_out,split_reset_out)beginif rising_edge(clk_1k) thensreg <= sne*t;end if;end process;process(

19、start_stop_out,split_reset_out,sreg)begincase sreg iswhen "111" =>if start_stop_out = '1' and split_reset_out = '0' then sne*t <= "011"else sne*t <= sreg;end if; when "011" =>if start_stop_out = '1' and split_reset_out = '0' t

20、hen sne*t <= "001"elsif start_stop_out = '0' and split_reset_out = '1' then sne*t <= "010"else sne*t <= sreg;end if;when "001" =>if start_stop_out = '0' and split_reset_out = '1' then sne*t <= "111"elsif start_sto

21、p_out = '1' and split_reset_out = '0' then sne*t <= "011"else sne*t <= sreg;end if;when "010" =>if start_stop_out = '0' and split_reset_out = '1' then sne*t <= "011"else sne*t <= sreg;end if;when others =>sne*t <= &qu

22、ot;111"end case;end process;end Behavioral;注：控制器设计时，巧妙地将状态编码和控制器输出的控制信号编码合二为一，即状态编码也是控制信号编码，使得程序形式上更为简单、清晰。4.程序仿真4.1分频器entity fp is Port ( clk_48M : in STD_LOGIC; clk_1k : out STD_LOGIC);end fp;architecture Behavioral of fp issignal count: STD_LOGIC_VECTOR(15 downto 0):=(others=>'0')

23、;beginprocess(clk_48M)beginif rising_edge(clk_48M) thenif count = 47999 thencount <=(others=>'0');elsecount <= count+1;end if;end if;end process;clk_1k <= count(15);end Behavioral;tb : PROCESSBEGINclk_48M <= '1' wait for 10.4 ns;clk_48M <= '0' wait for 10.4

24、ns;END PROCESS;4.1.1计数器电路综合4.1.2计数器电路仿真由图可得分频后的信号周期T=999333718ps0.001s 即的到了1KHz的信号由图可得时钟信号周期T=20845ps20.845ns 即的到了48MHz的时钟信号4.2同步计数器4.2.1计数器实现entity count_6 is Port ( clk_1k : in STD_LOGIC; d1 : out STD_LOGIC_VECTOR(3 downto 0); d2 : outSTD_LOGIC_VECTOR(3 downto 0); d3 : out STD_LOGIC_VECTOR(3 downt

25、o 0); d4 : out STD_LOGIC_VECTOR(3 downto 0); d5 : out STD_LOGIC_VECTOR(3 downto 0); d6 : out STD_LOGIC_VECTOR(3 downto 0);end count_6;architecture Behavioral of count_6 issignal z0,z1,z2,z3,z4,z5,z6: STD_LOGIC_VECTOR(3 downto 0):=(others=>'0');signal clr,en: STD_LOGIC;Beginclr <= '

26、0'-清零无效en <= '1'-计数使能有效d1 <= z1;d2 <= z2;d3 <= z3;d4 <= z4;d5 <= z5;d6 <= z6;process(clk_1k,clr)beginif rising_edge(clk_1k) thenif clr = '1' then z0<=(others=>'0');z1<=(others=>'0');z2<=(others=>'0');z3<=(others=&g

27、t;'0');z4<=(others=>'0');z5<=(others=>'0');z6<=(others=>'0');elsif en = '1' thenz0 <= z0+1;if z0 = 9 thenz0 <=(others=>'0');z1 <= z1+1;if z1 = 9 thenz1 <=(others=>'0');z2 <= z2+1;if z2 = 9 thenz2 <=(oth

28、ers=>'0');z3 <= z3+1;if z3 = 9 thenz3 <= (others=>'0');z4 <= z4+1;if z4 = 5 thenz4 <= (others=>'0');z5 <= z5+1;if z5 = 9 thenz5 <= (others=>'0');z6 <= z6+1;if z6 = 5 thenz6 <= (others=>'0');end if;end if;end if;end if;end

29、 if;end if;end if;end if;end if;end process;end Behavioral;4.2.2计数器仿真tb: PROCESSBEGINclk_1k <= '0'wait for 0.5 ms;clk_1k <= '1'wait for 0.5 ms;END PROCESS;0.01s位由图可以看出为十进制0.1s位由图可以看出为十进制1s位由图可以看出为十进制10s位由图可以看出为六进制1min位由图可以看出为十进制10min位由图可以看出为六进制4.2.3同步计数器电路综合4.3按键消抖电路4.3.1按键消抖电路

30、实现entity quedou is Port ( clk_1k : in STD_LOGIC; key_in : in STD_LOGIC; key_out : out STD_LOGIC);end quedou;architecture Behavioral of quedou issignal k1,k2: STD_LOGIC;signalt_1: STD_LOGIC_VECTOR(1 downto 0);beginprocess(clk_1k,key_in)beginif clk_1k'event and clk_1k='0' thenift_1 = 3 the

31、nk1 <= '1'elsek1 <= '0't_1 <=t_1+1;end if;k2 <= k1;end if;if key_in = '0' thent_1 <= "00"end if;end process;key_out <= not k1 and k2;end Behavioral;4.3.2按键消抖电路仿真tb: PROCESSBEGINclk_1k <= '0'wait for 0.5 ms;clk_1k <= '1'wait fo

32、r 0.5 ms;END PROCESS;PROCESSBEGINkey_in <= '1'wait for 10 ms;key_in <= '0'wait for 0.1 ms;key_in <= '1'wait for 0.09 ms;key_in <= '0'wait for 0.1 ms;key_in <= '1'wait for 0.11 ms;key_in <= '0'wait for 0.12 ms;key_in <= '1'w

33、ait for 0.11 ms;key_in <= '0'wait for 0.12 ms;key_in <= '1'wait for 0.1 ms;key_in <= '0'wait for 0.11 ms;key_in <= '1'wait for 0.12 ms;key_in <= '0'wait for 0.1 ms;key_in <= '1'wait for 0.1 ms;key_in <= '0'wait for 10 ms;ke

34、y_in <= '1'wait for 0.09 ms;key_in <= '0'wait for 0.08 ms;key_in <= '1'wait for 0.1 ms;key_in <= '0'wait for 0.11 ms;key_in <= '1'wait for 0.09 ms;key_in <= '0'wait for 0.1 ms;key_in <= '1'wait for 0.11 ms;key_in <= '

35、;0'wait for 0.12 ms;key_in <= '1'wait for 0.1 ms;key_in <= '0'wait for 0.11 ms;key_in <= '1'wait for 0.12 ms;key_in <= '0'wait for 0.1 ms;key_in <= '1'wait for 10 ms;END PROCESS;4.3.3按键消抖电路综合4.4八段译码器4.4.1八段译码器实现entity baduan is Port ( in_7 :

36、 in STD_LOGIC_VECTOR (3 downto 0); seg : out STD_LOGIC_VECTOR (7 downto 0);end baduan;architecture Behavioral of baduan isbeginprocess(in_7)beginCase in_7 iswhen "0000" => seg <="00000011"when "0001" => seg <="10011111"when "0010" => s

37、eg <="00100101"when "0011" => seg <="00001101"when "0100" => seg <="10011001"when "0101" => seg <="01001001"when "0110" => seg <="01000001"when "0111" => seg <="0

38、0011111"when "1000" => seg <="00000001"when "1001" => seg <="00001001"when others => seg <="11111101"end case;end process;end Behavioral;4.4.2八段译码器仿真tb :PROCESSBEGINin_7 <= "0000" wait for 1 ms;in_7 <= "000

39、1" wait for 1 ms;in_7 <= "0010" wait for 1 ms;in_7 <= "0011" wait for 1 ms;in_7 <= "0100" wait for 1 ms;in_7 <= "0101" wait for 1 ms;in_7 <= "0110" wait for 1 ms;in_7 <= "0111" wait for 1 ms;in_7 <= "1000"

40、; wait for 1 ms;in_7 <= "1001" wait for 1 ms;in_7 <= "1010" wait for 1 ms;in_7 <= "0000" wait for 1 ms;END PROCESS;由图可见仿真结果与程序完全符合4.4.3八段译码器电路综合View Technology Schematic ：4.5控制器4.5.1控制器entity kongzhiqi is Port ( clk_1k : in STD_LOGIC; start_stop_out : in STD_LO

41、GIC; split_reset_out : in STD_LOGIC; sreg_out : out STD_LOGIC_VECTOR (2 downto 0);end kongzhiqi;architecture Behavioral of kongzhiqi issignal sreg: STD_LOGIC_VECTOR(2 downto 0):="111"signal sne*t: STD_LOGIC_VECTOR(2 downto 0);beginprocess(clk_1k,start_stop_out,split_reset_out)beginif risin

42、g_edge(clk_1k) thensreg <= sne*t;end if;end process;process(start_stop_out,split_reset_out,sreg)begincase sreg iswhen "111" =>if start_stop_out = '1' and split_reset_out = '0' then sne*t <= "011"else sne*t <= sreg;end if; when "011" =>if s

43、tart_stop_out = '1' and split_reset_out = '0' then sne*t <= "001"elsif start_stop_out = '0' and split_reset_out = '1' then sne*t <= "010"else sne*t <= sreg;end if;when "001" =>if start_stop_out = '0' and split_reset_ou

44、t = '1' then sne*t <= "111"elsif start_stop_out = '1' and split_reset_out = '0' then sne*t <= "011"else sne*t <= sreg;end if;when "010" =>if start_stop_out = '0' and split_reset_out = '1' then sne*t <= "011"else sne*t <= sreg;end if;when others =>sne*t <= "111"end case;end process;sreg_out <= sreg ;end Behavioral;4.5.1控制器仿真tb: PROCESSBEGINclk_1k <= '0'wait for 0.5 ms;clk_1k <= '1'w