焊条保温筒检定程序

1、Procedure NumberHY-MP-COP-002程序编号Rev. No 版本1Page 页码1 of 6Document Status ：PRE/ 准备CFC/ 执行文件状态：Reference procedure No./Rev./参考程序编号 / 版本： N/A 不适用Document Title文件名称：Procedure for Calibration of Electrode Portable Oven焊条保温桶检定程序Document Type/文件类型： Management Procedure管理程序Name &TitleSignature/DateAppro

2、ved by姓名及职务签名及日期批准Prepared by编制职务：Title：Signature/Date：Reviewed by签名及日期审核QA ReviewerQA审核Translator翻译Translationreviewer 译审Copyright Declaration:版权声明：This document is the property of the SNPEMC. It must not be used, reproduced, transmitted ordisclosed without the prior written permission of SNPEMC。本程

3、序未经山东核电设备制造有限公司书面批准不得外用、复制和泄露Historical Records of Modification修改历史记录版本 Rev.发布日期Issue date修改范围及依据Scope and Basis of the Modification1Table of Contents目录1.Purpose 目的 . .42.Scope 范围 . .43.Reference Documents参考文件 .44.Responsibilities职责 .44.1Engineering Department工程部 .44.2Material Section物资组 .44.3QC Sec

4、tion QC部 .45.Calibration steps标定步骤 .55.1Check of prerequisites/检查先决条件 .55.2Temperature measuring method/温度测量方法. 55.3Disposal of results/结果处理 .56.Regular Inspection of Portable Oven During Construction焊条保温桶在使用过程中的检查7.Applicable forms适用表格 .61.Purpose 目的This procedure defines the calibration method and

5、 management requirements for electrode portable oven to CV assembly and erection at HaiYang site.本程序叙述了焊条保温筒的检定方法和使用管理要求。2.Scope 范围This procedure is applicable for the calibration, using and managing of electrode portable oven of HaiYang CV Project of SNPEMC.本程序适用于SNPEMC海阳 CV项目焊接生产过程中焊条保温筒的检定、使用和管理工

6、作。3.Reference Documents参考文件Quality Assurance Manual for Haiyang ProjectHY-QAM海阳项目质量保证手册HY-QAM4.Responsibilities职责4.1Engineering Department工程部根据生产需要，编制焊条保温筒需求计划；正确使用焊条保温筒。4.2 Material Section物资组Be responsibleforprocureelectrodeportableoven and buildup calibrationrecordsforportable oven.采购焊条保温筒，并建立焊条保

7、温筒标定状态台帐。Be responsible for the periodicalcalibration,management and maintenance of electrodeportable oven.负责焊条保温筒进行定期的标定、管理和维护。按焊接材料控制程序附录6 的要求在保温桶上粘贴正确的标签。4.3 QC Section QC部Sign off the calibration records of electrode portable oven.对焊条保温筒检定记录签字确认；Be responsiblefor inspectionofthe qualificationlab

8、els;supervisetheusage ofelectrode portable oven.检查焊条保温筒上粘贴合格证，对焊条保温筒的使用情况进行监督。5.Calibration steps标定步骤5.1Check of prerequisites/检查先决条件5.1.1 Power supply（ 24V or 36V ） , calibrated thermometer, record form;电源（ 24V 或 36V）、标定合格的温度计，记录表格；Qualified operator and QC personnel;合格的操作人员和质检人员。5.2 Temperature me

9、asuring method/温度测量方法5.2.1Switch on power supply for electrode portable oven（ 24V 或 36V） ;接通保温筒电源（24V 或 36V）；5.2.2The total measuring time is 1 hour, filling in the records every 20 minutes;测量时间为 1 小时，每间隔20 分钟记录；5.2.3The readingsof measured temperature shallbe withinthe range of 80 150，the tolerance

10、is ± 10 .所测温度读数应在80 150范围内，温度范围±10. 。5.3 Disposal of results/结果处理5.3.1The electrode thermostats shall be replaced or repaired if they are disabled.在检定过程中，如发现保温筒不能达到使用要求应及时更换、修理；5.3.2QC shall sing on theeligiblecalibratedportableoven, and confirm the acceptance labelhas been pasted on porta

11、ble oven.QC在检定合格的保温筒标定记录上签字，并监督物资组在标定合格的保温筒外壁贴上合格标签。6.Regular Inspection of Portable Oven During Construction焊条保温桶在使用过程中的检查6.1General Requirement 通用要求Electrode portable oven will be inspected during welding construction.焊条保温桶在焊接施工的全过程中要对其温度进行检查。Portable oven shall be inspected prior to putting electrodes into it. These electrodescan only be put into it after the temperature are confirmed.在焊条放入保温桶时应第一次对保温桶进行温度检查。确保温度在规定范围后方可将焊条放入。焊条放入保温桶后每隔2 小时由QC人员对其温度进行一次抽查。抽查个数应占总使用个数的50%或以上。检查结果形成记录，记录表格见第7 部分。焊接施工结束后，如果保温桶还有剩余未用完的焊条，则应在归还前对内部温度进行一次检查。7.Applicable forms适用表格InspectionRecord forElectr