版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领
文档简介
1、Lesson FiveText Fuel oil systemFuel oil is thought to be one of the main factors having much to do with the operation and maintenance of an engine. When selecting a fuel oil, there are more than ten factors to be considered, among those which affect combustion are the fuel o i l s v i s c o s i t y,
2、 c e t a n e n u m b e r ( 十 六 烷 值十 六 烷 值 ) a n d calorific value(热值热值); the sulphur(硫分硫分) in it and its carbon residues(残炭值残炭值) and ash(灰分灰分) are factors that decide the formation of combustion products;and the engines maintenance has a lot to do with its flash and setting points(闪点和凝点闪点和凝点), speci
3、fic gravity(密度密度), viscosity, water content(水分水分) and the mechanical impurities(机械杂机械杂质质) in it.The work that fuel does in an engine not only depends upon the fuel oil itself, but also upon its working condition, which here means the fuel system. The fuel oil system for a diesel engine can be consid
4、ered in two partsthe fuel supply and the fuel injection systems. Fuel supply deals with the provision of the fuel oil suitable for use by the injection system.Fuel oil supplyA slow-speed two-stroke diesel is usually arranged to operate continuously on heavy fuel or residual oil(渣油渣油) and have availa
5、ble a diesel oil supply for maneuvering conditions. The whole fuel system will then embody two almost entirely separate systems, one for diesel fuel and one for high viscosity fuel. The latter will embody heating arrangements and means to control the temperature of the fuel to ensure that it is adeq
6、uately fluid when stored, transferred, cleaned and injected. In a typical fuel installation on board a ship for a modern diesel engine, separate filling connections for the diesel and heavy fuel tanks are provided. In use, the filling connections on deck are connected to shore hoses and the fuel oil
7、 bunkers(燃燃料舱料舱) are then distributed to various double bottom, deep, wing and side tanks(双层底舱,双层底舱,深 舱 , 舷 侧 舱 和 边 舱深 舱 , 舷 侧 舱 和 边 舱 ) a s necessary. Steam heating coils(蒸汽加热盘蒸汽加热盘管管) are installed in the various tanks to ensure that the temperature of the oil can be raised to reduce the viscosity
8、 to a level that will ensure easy pump-ability. Pipes used for transferring high viscosity fuel should be well lagged(加保温层加保温层) and long runs of piping(管道系统管道系统) should have steam-tracing pipes(蒸汽伴热管蒸汽伴热管) fitted.The fuel oil is drawn from the bunker tanks through a duplex strainer(双联过滤器双联过滤器) by a
9、transfer pump and thence to dirty oil storage or setting tanks. Leaving the fuel in the setting tanks whilst keeping it hot to reduce its viscosity allows the heavier impurities and any water present to settle to the bottom of the tank. The sediment(沉淀物沉淀物) and water are drawn off leaving the remain
10、der ready for cleaning. I t i s t h e n p a s s e d t o a purification(净化净化) system for treatment and from there to the clean heavy fuel tank, which known as the service tank.From the clean heavy fuel tank the oil gravitates through a heated buffer(缓冲柜缓冲柜)、 or balance tank to the booster pumps(增压泵增压
11、泵)and is discharged through a fuel heater and filter to a viscosity regulator and from there to a duplex fine filter on the suction side of the main engine fuel pumps.Fuel excess to requirements is spilled back into the system via the buffer tank. The viscosity regulator controls the fuel oil temper
12、ature in order to provide oil at the c o r r e c t v i s c o s i t y f o r combustion. A pressure-regulating valve ensures a constant pressure at the fuel main. The valve can be opened to warm through the system by circulating with heated oil. Regular attention to the d r a i n i n g o f h e a t e d
13、 settling(setting tank) and ready use tank(service tank) is advisable to eliminate the r e s u l t s o f c o n t i n u o u s condensation which can be very heavy under certain climatic conditions. Usually the settling and ready use tanks are lagged to reduce heating losses.The system will include va
14、rious safety devices such as low level alarms and remote operation of tank outlet valves in the events of fire. The diesel oil supply system similarly uses transfer pumps to draw oil from the bunker tanks. The oil is then purified and stored in service tank. The diesel oil enters the system through
15、a three way valve which permits the supply of only one type of oil to the system. The engine must be changed over to running on diesel oil for 30 minutes or more before a long period of standstill(停止停止). Diesel oil required less heating, and thus the change from one fuel to another should take place
16、 gradually to allow temperatures in the system to stabilize.Fuel InjectionThe function of the fuel injection system is to provide the amount of fuel at the right moment and in a suitable condition for the combustion process. That means, the fuel injection system for diesel engines must be able to su
17、pply a metered(定量定量) amount of fuel to each cylinder for each power stroke according to the load on the engine, and must include a timing mechanism to ensure that d e l i v e r y o f t h i s f u e l commences at the correct moment, and must have a means to atomize(将将喷成喷成雾状雾状) the fuel. The type of i
18、njection system most commonly used in modern diesel engines is the jerk pump(脉动泵脉动泵) system. In the system, a separate injection pump is provided for each cylinder which operates once every cycle.The barrel and plunger, together with the cam, are dimensioned to displace (discharge) fuel at the rate
19、it is required in the combustion chamber. P o r t s i n t h e b a r r e l i n combination with slots in the p l u n g e r, o r s e p a r a t e mechanically operated spill valves(回流阀回流阀), determine the amount of fuel delivered and the timing of its entry to the cylinder. Plunger barrelEach pump is co
20、nnected to the injector, or injectors, serving one cylinder. These injectors have spring loaded differential needle valves which are set to ensure that the fuel is raised to a sufficiently h i g h p re s s u re t o c a u s e atomization(雾化雾化) when they automatically open to admit it to the cylinder.
21、Fuel Oil QualityViscosity is not a measure of the fuel quality, but determines the complexity of the fuel heating and handling system, which should be considered when estimating installation economy. The standard engine fuel system is designed for fuels up to the viscosity class 55 mm2/s. When the d
22、ensity exceeds 0.991g/ml at 15, water, and to some extent solid matter, can no longer be removed with certainty by a centrifuge(离心离心分离机分离机). Centrifuging systems that are claimed to be able to clean fuel oils with densities up to 1.010g/ml at 15 are available. If such systems as the so called contro
23、lled discharge design are installed, fuels with densities up to 1.010 g/ml at 15 may be used.Note: Fuel oils having high density in combination with low viscosity may have low ignition quality. High sulphur content increases the risk for corrosion and wear, particularly at low loads, and may contrib
24、ute to high-temperature deposit formation. The lubricating oil specification must be matched to this. High ash content causes abrasive(研磨的研磨的) wear, and may cause high temperature corrosion and contributes to formation of deposits. T h e m o s t h a r m f u l a s h constituents(成份)(成份) are vanadium(
25、钒钒) sodium(钠钠) combinations(化合物化合物). High vanadium content causes hot corrosion on exhaust valves particularly in combination with high sodium content. The corrosion increases with increased temperatures (increased engine output).High Conradson carbon(康拉康拉特逊残碳值特逊残碳值) may cause deposit formation in c
26、ombustion chamber and exhaust system, particularly at low engine output. High content of asphalt (沥青沥青) may contribute to deposit formation in combustion chamber and exhaust systems (at low loads). Asphalt may under certain circumstances, precipitate(使使沉淀沉淀) from the fuel and block filters and/or ca
27、use deposits in the fuel system, precipitating asphalt may also cause excessive centrifuge sludge(油油泥泥). Heavy fuels may contain up to 1% water at delivery. Water may also originate from the installation in bunker tanks. To avoid difficulties in the engine fuel injection system water must be removed
28、. Although low ignition quality produces long ignition delay, advancing the ignition timing makes things only worse; fuel is injected at a lower compression temperature and this will produce even longer ignition delay. Aluminum(铝铝) and Silicon(硅硅)Fuels may contain highly abrasive particles composed
29、of aluminum and silicon oxides(氧氧化物化物) known as catalytic fines(催化粉末催化粉末) from certain refining(精练精练) processes. If not removed by efficient fuel treatment, wear down of high pressure fuel pumps, nozzles and cylinder liners in a few hours may expected. Reading MaterialA. Dual purpose plus(additive)
30、descriptionDual Purpose Plus is a concentrated combustion improver(集中燃烧促进剂集中燃烧促进剂) for heavy fuel oils. It also has fuel conditioning properties. Product PropertiesThe catalysts(催化剂催化剂) in Dual Purpose Plus react with heavy f u e l p a r t i c l e s d u r i n g combustion. The fuel ignition temperat
31、ure is reduced, resulting in increased combustion efficiency with less carbon left to form smoke and soot(烟灰烟灰). Engine and exhaust systems are kept cleaner with longer service life and less maintenance. Anti-polymerization(反聚合作反聚合作用用) agents inhibit(抑制抑制) sludge formation, while dispersants(分分散剂散剂)
32、 stabilize the fuel. This results in a cleaner fuel system and better fuel flow, g i v i n g i m p r o v e d f u e l atomization and greater combustion efficiency.Sulphuric acid(硫酸硫酸) corrosion caused by condensing exhaust gases may be seen in any of the cooler parts of the boiler or engine system.
33、Typical problem areas are cylinder liners (cloverleaf(苜蓿苜蓿叶形的叶形的) corrosion), valve stems and funnel uptakes.D u a l P u r p o s e P l u s catalytically(催化催化) inhibits the formation of acid gases and so reduces the amount of acid present, thereby reducing acid corrosion. Directions for Use and Dose(
34、剂量剂量) RatesDual Purpose Plus is completely oil-soluble and should be added via a metering pump into the suction side of the booster pump. Alternatively, it can be added into the settling tank. If so, the dose rate should be increased by 10%. As a general guide, the average dosage(剂量剂量, 配药配药, 用量用量) s
35、hould be 1:4000. Alterations can then be made according to operating experience and results obtained. B. Dieselite(柴油助燃剂柴油助燃剂) descriptionDieselite is a multi-functional fuel treatment containing combustion catalysts and ash modifiers(灰分调节灰分调节剂剂). It is intended for use in diesel engines and boilers
36、 burning residual fuels.Product PropertiesCarbon residue formation during combustion is inhibited by catalysts that lower the ignition temperature of heavy asphaltic particles. C o m b u s t i o n t i m e i s consequently increased, leading to a reduction of tarry(焦油焦油) deposits and carbonaceous(炭炭的
37、、炭质的的、炭质的) fire-scale. Ash modifiers combine with fuel combustion ash to raise the sinter(烧结物烧结物,熔渣熔渣) and melting points of the ash above the engine or boiler normal operating temperatures. High temperature corrosion is m i n i m i z e d , r e d u c i n g maintenance and extending service life. The
38、 majority of ash formed is ejected with the exhaust gases in a fine, solid state, and any ash remaining in the exhaust system is easily removed by light brushing. The conversion of fuel sulphur to potentially corrosive sulphur trioxide(三氧化物三氧化物) gas is also inhibited. Sulphur trioxide reacts with co
39、ndensed steam in the exhaust trunking, funnel uptakes and other cooler zones to form sulphuric acid. Dieselite is a wide spectrum a d d i t i v e i n t e n d e d f o r continuous use. Directions for Use and Dose RatesFor best results, Dieselite should be dosed automatically using a metering pump to
40、dose into the fuel feed line as near to the injector or burner pump as possible. Where micro carbon residue ( M C R ) ( 微 量 法 残 炭 值微 量 法 残 炭 值 ) o r vanadium/sodium analysis is available, use the tables given by the manufacturer. If no analysis is available, use an initial dose rate of 1:4000 and ad
41、just according to results obtained. C. TEST OF FUEL INJECTION VALVE For injection test on fuel injection valve, perform with use of the fuel injection valve tester(喷油嘴试验台喷油嘴试验台). Adjustment of Fuel Injection PressureCheck fuel injection initial pressure by use of the fuel injection valve tester, and
42、 adjust this pressure to the designated value. For this adjustment, remove the cap nut first, and then adjust by means of the adjusting bolt. If components (needle Valve, spring, etc.) of fuel injection valve are replaced as well as the valve is disassembled, be sure to check the fuel injection pres
43、sure. If the injection nozzle is clogged, remove the carbon sticking to the nozzle part, using either carbon removing agent or cresol solution(甲酚溶液甲酚溶液); never use sandpaper(砂纸砂纸) or the like. Remember that shape of the n o z z l e g r e a t l y a f f e c t s atomization of fuel oil. Atomization Tes
44、tTurn the hand lever of the fuel injection tester at the rate of 1-3 turns per second, and check f o r c o n d i t i o n o f f u e l atomization under this circumstance. Confirm that fuel oil is evenly spread out as it is injected and that there is no abnormality(异异常常; 变态变态) due to clogged nozzle. Since the tip part of this needle valve is in double cone shape, if the rate of the lever is slowed down, atomization becomes m u c h c o a r s e r t h a n a conventional needle valve. However, in actual engine operation, fuel oil is no
温馨提示
- 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
- 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
- 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
- 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
- 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
- 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
- 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 初中七年级英语下册Unit 1 Section A词汇语法与句型教学设计
- 高二英语听力教学设计:仿真特训中推理判断与信息重组策略的落实
- 小学四年级英语Cool clothes教案
- 八年级地理教学设计:中国气候类型判读与季风显著性中考突破
- 高二化学选择性必修1第三章第1、2节化学反应速率与影响因素教学设计
- 高考语文二轮复习修辞手法赏析教学设计
- 高中化学选择性必修3 甲醛与酮的性质及应用教学设计
- 小学六年级心理健康《学会感恩 与爱同行》教学设计
- 初中八年级数学《认识一次函数》第一课时教学设计
- 小学三年级综合实践活动《时间都去哪了》教学设计
- 殡葬服务质量考核细则
- 泌尿外科急诊经皮肾穿刺造瘘手术教学查房
- 2026年中国酒吧行业市场现状、未来前景预测及行业发展趋势
- 2026年医疗器械监督管理条例培训试卷附答案
- 心脏瓣膜病护理查房
- 多资产配置全景研究系列控波御险:多资产组合风险管理方法论
- 《脓毒症和脓毒性休克管理国际指南2026》解读课件
- 新版西师版五年级上册数学全册教案(完整版)教学设计含教学反思
- 2025年四川省成都市新都区中考数学一诊试卷
- 人工智能驱动下的人才竞争力评价与专业演变研究
- 2026-2030中国电信反欺诈行业前景调查及未来趋势洞察研究报告
评论
0/150
提交评论